ページ1に含まれる内容の要旨
IMPORTANT MANUAL Do Not Throw Away
02153
OPERATOR'S MANUAL
WARNING:
MODEL:
Read this Manu al and follow all Warnings and
Safety Instructions. Fail ure to do so can re sult
in serious in ju ry.
XT24H48YT
LAWN TRACTOR
ALWAYS WEAR EYE PROTECTION DURING OPERATION
Visit our website: www.poulan-pro.com
196712 Rev. 1 02.14.05 TR
Printed in U.S.A.
ページ2に含まれる内容の要旨
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS . FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Do not operate machine without the entire grass catcher, WARNING: In order to prevent ac- discharge guard, or other safety devices in place and ci den tal starting when setting up, working. trans port ing, ad just ing or making re- Slow
ページ3に含まれる内容の要旨
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE Tragic accidents can occur if the operator is not alert to Never operate machine in a closed are. Keep all nuts and bolts tight to be sure the equipment the presence of children. Children are often attracted to the ma chine and the mowing activity. Never assume that is in safe working condition. Never tamper with safety devices. Check their proper children will remain where you last saw the
ページ4に含まれる内容の要旨
CONGRATULATIONS on your purchase of a new tractor. PRODUCT SPECIFICATIONS It has been designed, engineered and manu fac tured to give Gasoline Capacity 4.0 Gallons you the best possible dependability and performance. and Type: Unleaded Regular Should you experience any problem you cannot easily rem- Oil Type (API-SG-SL): SAE 30 (above 32°F) edy, please contact your nearest authorized service center/
ページ5に含まれる内容の要旨
UNASSEMBLED PARTS Mower Steering Wheel (2) Retainer Springs (5) Retainer Springs (single loop) (double loop) Steering (1)Front Plate Steering Wheel Assembly Wheel (2)Flanged Adapter Insert Pins (1) Large Flat Gauge Wheels Washer (4) Adjusting Bar Steering Sleeve (4) Washers 3/8 x 3/4 x 14 Ga. (4) Wheels (4) Retainer Springs (1) Hex nut 1/2-20 (double loop) (4) Locknut 3/8-16 (1) Hex Bolt 1/4-28 x 1-1/4 (4) Clevis Pins Seat (4) Shoulder Bolt (1) Oil Drain Tube Slo
ページ6に含まれる内容の要旨
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY STEERING WHEEL A socket wrench set will make assembly easier. Stan dard INSERT wrench sizes are listed. LOCK NUT (1) 3/4" wrench Pliers (1) 9/16" wrench
ページ7に含まれる内容の要旨
02173 ASSEMBLY NOTE: You may now roll or drive your tractor off the skid. SEAT Follow the ap pro pri ate instruction below to remove the tractor from the skid. TO ROLL TRACTOR OFF SKID (See Op- er a tion section for location and function of con trols) SEAT PAN Press lift lever plunger and raise attachment lift lever to its highest po si tion. Release parking brake by de press ing clutch/brake ped al. SHOULDER Place freewheel control in "trans mis sion dis en gaged BOLT po
ページ8に含まれる内容の要旨
02510 ASSEMBLY Adjust gauge wheels before operating mower. See “TO If equipped, turn height ad just ment knob coun ter - ADJUST GAUGE WHEELS” in the Operation sec tion clock wise until it stops. of this manual. Lower mower linkage with attachment lift control. Be sure belt tension rod is in dis en gaged position. RETAINER SPRING Install belt into electric clutch pulley groove. Place the suspension arms on outward pointing deck PIN pins. Retain with double loop r
ページ9に含まれる内容の要旨
ASSEMBLY Connect anti-sway bar to chassis bracket under left ✓CHECKLIST foot rest and retain with double loop retainer spring. BEFORE YOU OPERATE YOUR NEW TRAC TOR, WE If equipped, turn height adjustment knob clock wise to WISH TO ASSURE THAT YOU RECEIVE THE BEST PER- remove slack from mower sus pen sion. FORMANCE AND SATISFACTION FROM THIS QUALITY Raise deck to highest position. PRODUCT. Adjust gauge wheels before op erat ing mower as shown PLEASE REVIEW THE FOLLOWING
ページ10に含まれる内容の要旨
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. FAST SLOW REVERSE NEUTRAL HIGH LOW CHOKE IGNITIONSWITCH P ENGINEON ENGINESTART PARKINGBRAKE ENGINEOFF REVERSE PARKINGBRAKE PARKINGBRAKE OPERATION LOCKED UNLOCKED SYSTEM(ROS) OILPRESSURE BATTERY OVERTEMP FUEL REVERSE FORWARD MOWERHEIGHT MOWERLIFT LIGHT 15 15 ATTACHMENT ATTACHMENT SLOPEHAZARDS DANGER,KEEPHANDS KEEPAREACLEAR CLUTCHDISENGAGED CLUTCHENGAGED ANDFEETAWAY
ページ11に含まれる内容の要旨
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. IGNITION SWITCH HOURMETER ROS "ON" POSITION AMMETER CHOKE CONTROL LIFT LEVER AT TACHMENT PLUNGER CLUTCH THROTTLE SWITCH CONTROL ATTACHMENT LIFT LEVER CLUTCH/BRAKE PEDAL HEIGHT ADJUSTMENT KNOB LIGHT SWITCH PARKING BRAKE FREE WHE
ページ12に含まれる内容の要旨
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while op- erating your tractor or per forming an y adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY HOW TO USE YOUR TRACTOR POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY TO BE DIS CHARGED, (DEAD). TO SET PAR
ページ13に含まれる内容の要旨
OPERATION TO ADJUST GAUGE WHEELS (See Fig. 8) ATTACHMENT "ENGAGED" PO SI TION LIFT LEVER Gauge wheels are properly adjusted when they are slightly HIGH PO SI TION off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain LOW conditions. POSITION NOTE:Adjust gauge wheels with tractor on a fl at level surface. Adjust mower to desired cutting height (See “TO AD- JUST MOWER
ページ14に含まれる内容の要旨
OPERATION Remove oil fi ll cap/dipstick and wipe clean, reinsert the Avoid stopping or changing speed on hills. dipstick and screw cap tight, wait for a few seconds, If slowing is necessary, move throttle control lever to remove and read oil level. If necessary, add oil until slower position. “FULL” mark on dipstick is reached. Do not overfi ll. If stopping is absolutely necessary, push clutch/brake For cold weather operation you should change oil for pedal quickl
ページ15に含まれる内容の要旨
OPERATION WARM WEATHER STARTING (50° F and above) NOTE: During this procedure there will be no movement When engine starts, slowly push choke control in until of drive wheels. The air is being removed from hydraulic the engine begins to run smoothly. If the engine starts to drive system. run roughly, pull the choke control out slightly for a few Move motion control lever to neutral (N) position. Shut- seconds and then continue to push the control in slowly. off engine and set pa
ページ16に含まれる内容の要旨
maint_sch-tractore.ROS.e MAINTENANCE MAINTENANCESCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES Check Brake Operation Check Tire Pressure Check Operator Presence and ROS Systems T R Check for Loose Fasteners 5 A Sharpen/Replace Mower Blades 3 C Lubrication Chart T Check Battery Level 4 0 Clean Battery and Terminals R Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (without oil filter) 1,2 E Clean Air Filt
ページ17に含まれる内容の要旨
02544 MAINTENANCE TRACTOR BLADE CARE Always observe safety rules when per forming an y main- For best results mower blades must be kept sharp. Re place te nance. bent or damaged blades. BRAKE OPERATION CAUTION: Use only a replacement blade If tractor requires more than fi ve (5) feet to stop at highest approved by the manufacturer of your speed in high est gear on a level, dry concrete or paved tractor. Using a blade not approved surface, then brake must be checked and ad just ed. (See
ページ18に含まれる内容の要旨
MAINTENANCE TRANSAXLE PUMP FLUID CENTER HOLE The transaxle was sealed at the factory and fl uid main te - nance is not required for the life of the transaxle. Should BLADE 5/8" BOLT the transaxle ever leak or require servicing, contact your OR PIN near est au tho rized ser vice center/department. ENGINE LUBRICATION FIG. 13 Only use high quality detergent oil rated with API service classifi cation SG-SL. Select the oil’s SAE viscosity grade BATTERY according to your expected operating temper
ページ19に含まれる内容の要旨
MAINTENANCE Unlock drain valve by pushing inward and turning MUFFLER coun ter clock wise. To open, pull out on the drain valve. Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam- After oil has drained completely, close and lock the age. drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. SPARK PLUGS Remove the drain tube and replace the cap onto to the
ページ20に含まれる内容の要旨
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in “DISENGAGED” position. Turn ignition key to “STOP” and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug
