ページ1に含まれる内容の要旨
MODEL NO. PO17H42STB
17.0 HP 42 Inch
Lawn Tractor
For Parts and Service, contact our authorized distributor: call 1-800-849-1297
For Technical Assistance: call 1-800-829-5886
00420-poulan
187301 05.27.03 TR
PRINTED IN U.S.A.
ページ2に含まれる内容の要旨
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS . FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. DO NOT: I. GENERAL OPERATION Do not turn on slopes unless necessary, and then, Read, understand, and follow all instructions in the turn slowly and gradually downhill, if possible. manual and on the machine before starting. Do not
ページ3に含まれる内容の要旨
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS Be sure the area is clear of other people before mowing. Stop WARNING: In order to prevent ac ci - machine if anyone enters the area. den tal starting when setting up, trans- Never carry passengers or children even with the blades por ting, ad just ing or making repairs, off. al ways dis con nect spark plug wire Do not mow in reverse unless absolutely necessary. Al ways and place wire where it can not contact look
ページ4に含まれる内容の要旨
CONGRATULATIONS on your purchase of a new tractor. PRODUCT SPECIFICATIONS It has been designed, engineered and manufa ctured to giv e Gasoline Capacity 1.25 Gallons you the best possible dependability and performance. and type: Unleaded Regular Should you experience any problem you cannot easily rem- Oil Type (API-SF-SJ): SAE 30 (above 32°F) edy, please contact your nearest authorized service center/ SAE 5W-30 (below 32°F) department. We have com pe tent, well-trained tech ni cians O
ページ5に含まれる内容の要旨
UNASSEMBLED PARTS Steering Wheel Seat (1) Washer 17/32 x 1-3/16 x 12 Gauge Steering Boot (1) Lock Washer 1/2 Steering Steering Wheel Extension Insert (1) Bolt Shaft Steering Wheel Key Adapter (1) Large Flat Washer (1) Locknut 1/2-20 (2) Keys (1) Oil Drain Tube Slope Sheet (1) Locknut 1/4-28 (1) Hex Bolt 1/4-28 x 1-1/4 5
ページ6に含まれる内容の要旨
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY INSERT A socket wrench set will make assembly easier. Stan dard wrench sizes are listed. 1/2 LOCK WASHER (1) 3/4" wrench Pliers LARGE FLAT (2) 7/16" wren
ページ7に含まれる内容の要旨
ASSEMBLY HOW TO SET UP YOUR TRACTOR INSTALL SEAT (See Fig. 2) SEAT PAN Adjust seat before tightening adjustment bolt. LABEL Remove adjustment bolt, lock washer and fl at washer se cur ing seat to cardboard packing and set aside for as sem bly of seat to tractor. Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan. Push down on seat to
ページ8に含まれる内容の要旨
ASSEMBLY ✓CHE CKLIST CHECK TIRE PRESSURE BEFORE YOU OPERATE AND ENJOY YOUR NEW TRAC- The tires on your tractor were overinfl ated at the factory TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE for shipping purposes. Correct tire pressure is important BEST PERFORMANCE AND SATISFACTION FROM THIS for best cutting performance. QUALITY PRODUCT. Reduce tire pressure to PSI shown in “PRODUCT PLEASE REVIEW THE FOLLOWING CHECKLIST: SPEC I FI CA TIONS” section of this manual. ✓ All assembly inst
ページ9に含まれる内容の要旨
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. FAST IGNITION REVERSE NEUTRAL HIGH LOW SLOW CHOKE P LIGHTS ON ENGINE START PARKING BRAKE ENGINE OFF ENGINE ON PARKING BRAKE PARKING BRAKE LOCKED UNLOCKED OIL PRESSURE BATTERY REVERSE OVER TEMP FUEL FORWARD MOWER HEIGHT MOWER LIFT LIGHT 15 15 15 ATTACHMENT ATTACHMENT SLOPE HAZARDS CLUTCH ENGAGED CLUTCH DISENGAGED DANGER, KEEP HANDS KEEP AREA CLEAR AND FEET AWAY
ページ10に含まれる内容の要旨
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. ATT ACH MENT CLUTCH LEVER LIGHT SWITCH IGNITION POSITION SWITCH LIFT LEVER PLUNGER THROTTLE/CHOKE CONTROL ATTACHMENT LIFT LEVER CLUTCH/BRAKE PEDAL PARKING BRAKE MOTION FREE WHEEL CONTROL CONTROL LEVER FIG. 4 Our tractors confor
ページ11に含まれる内容の要旨
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your trac- tor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY HOW TO USE YOUR TRACTOR POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DIS CHARGED, (DEAD). TO SET PARK
ページ12に含まれる内容の要旨
OPERATION TO TRANSPORT (See Figs. 4 and 7) TO OPERATE MOWER (See Fig. 6) When pushing or towing your tractor, be sure to disengage Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with transmission by placing freewheel control in free wheel ing po si tion. Free wheel control is located at the rear drawbar the engine running and the attachment clutch engaged will shut off the engine. of tractor. Select desired height of
ページ13に含まれる内容の要旨
OPERATION COLD WEATHER STARTING ( 50° F and below) ADD GASOLINE When engine starts, allow engine to run with the Fill fuel tank to bottom of fi ller neck. Do not overfi ll. throttle control in the choke position until the engine Use fresh, clean, regular un lead ed gasoline with a runs roughly, then move throttle control to fast posi- minimum of 87 octane. (Use of leaded gasoline will tion. This may require an engine warm-up period from increase carbon and lead oxide deposits a
ページ14に含まれる内容の要旨
OPERATION Move motion control lever to neutral (N) position. Shut- off engine and set parking brake. Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this sec tion of manual). Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal. Slowly move motion control lever forward, after the
ページ15に含まれる内容の要旨
maint_sch-tractore.new1 MAINTENANCE MAINTENANCESCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES Check Brake Operation Check Tire Pressure Check Operator Presence and Interlock Systems T R Check for Loose Fasteners 5 A Sharpen/Replace Mower Blades 3 C Lubrication Chart T Check Battery Level 4 0 Clean Battery and Terminals R Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (without oil filter) 1,2 E Clean Air
ページ16に含まれる内容の要旨
MAINTENANCE TRAILING TRACTOR MANDREL EDGE UP ASSEMBLY Always observe safety rules when performing any main- BLADE te nance. CEN TER HOLE BRAKE OPERATION If tractor requires more than six (6) feet stopping distance LOCK WASHER at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Ad just ments section of this manual). STAR FLAT WASHER TIRES BLADE BOLT (GRADE 8)* Maintain proper air pressure in all tires (See “PROD UCT *A GRADE 8 HEAT TREA
ページ17に含まれる内容の要旨
MAINTENANCE NOTE: The original equipment battery on your tractor is NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) maintenance free. Do not attempt to open or remove caps improve starting in cold weather, these multi-viscosity oils or covers. Adding or checking level of electrolyte is not will result in increased oil consumption when used above necessary. 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. TO CLEAN BATTERY AN
ページ18に含まれる内容の要旨
MAINTENANCE ENGINE COOLING FINS (See Fig. 13) HAN DLE Remove any dust, dirt or oil from engine cooling fi ns to prevent engine damage from overheating. Remove screws from blower housing and lift housing and dipstick tube assembly off engine. Cover oil fi ll opening to prevent entry of dirt. Use compressed air or stiff bristle brush to thoroughly COVER clean engine cooling fi ns. To reassemble, reverse above procedure. CARTRIDGE PRE-CLEANER SCREWS BLOWER HOUSING SCREWS TABS B
ページ19に含まれる内容の要旨
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR AD JUST - MENTS: Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in “DISENGAGED” position. Turn ignition key to “STOP” and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in con- tact with plu
ページ20に含まれる内容の要旨
SERVICE AND ADJUSTMENTS SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18) Raise mower to its highest position. MANDREL At the midpoint of both sides of mower, measure height from bot tom edge of mower to ground. Distance “A” on both sides of mower should be the same or within "D" "D" 1/4" of each other. If adjustment is necessary, make adjustment on one FIG. 19 side of mower only. To raise one side of mower, tighten lift link ad just ment BOTH FRONT LINKS MUST BE EQUAL IN
