ページ1に含まれる内容の要旨
To The Owner • Carton Contents • Assembly • Parts Lists • Warranty
OPERATOR’S MANUAL
Twin Rear Bagger Kit
For Lawn Tractors
with 38” & 42” Decks
Models OHD-190-180
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
FORM NO. 769-02302
PRINTED IN U.S.A. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 01/04/2006
ページ2に含まれる内容の要旨
This Operator’s Manual is an important part of your new grass collector. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. TABLE OF CONTENTS 1. Rider Identification ........................................... Page 3 5. Attach Discharge Chute ...................................Page 10 2. Carton Contents .............................................. Page 4 6. Parts List ........................................................
ページ3に含まれる内容の要旨
™ FastAttach Twin Bag Model Plate Grass Collector The Model OEM-190-180 Twin Bag Grass Collector is a 1 grass collection system designed for use on all MTD 38” & 42” cut FastAttach™ compatible lawn tractors (except Rider Model 2001 Yard-Man Revolution/White Outdoor ZTT). The instructions in this manual are divided into sections. Identification Carefully read all sections pertaining to your model of rider, and study the illustrations to ensure proper installa- tion and usage of this attach
ページ4に含まれる内容の要旨
CONTENTS OF CARTON Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Figure 3. Hardware part numbers are shown in parentheses. 2 One Chute Tube One Support Tube One Discharge Chute Assembly One Grass Catcher Cover Assembly Carton Two Grass Bag Assemblies One Mounting Bracket Contents Grass Catcher Cover If you are missing Assembly any parts, please Chute Tube Discharge Chute do not contact the
ページ5に含まれる内容の要旨
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with a hardware pack enclosed. This hardware pack may contain extra parts for installation on a different rider from which you have. Please check your hardware pack against the 2 illustration below in accordance with your model of rider as determined in Section 1 of this manual. Carton For all Model Series 650 through 699 tractors Contents (2) A (2) C (1) (1) (2) F2 F1 B (LH) (RH) If you are missing any parts, please For all Mo
ページ6に含まれる内容の要旨
Attaching The Bracket Assembly Model Series 600 through 619 3 IMPORTANT: Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the Attaching tractor engine and set the parking brake. Bracket 1. For convenience, pivot the seat forward and leave it in that position until the grass collector is fully Remove Assembly mounted and assembled. Pin Model Series 600 2. Remove the hairpin clip and clevis pin from the rear through 619 of the mounting bracket assembl
ページ7に含まれる内容の要旨
Assembling Support Brackets Model Series 650 through 699 3 IMPORTANT: Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. Attaching 1. Remove the top four self-tapping screws from the rear Support of the lawn tractor. See Figure 7 on the previous page. Clevis Pin 2. Place the right hand grass catcher support bracket (F1 Bracket & from Figure 4), in position, with the wide end on top and the narrow end point
ページ8に含まれる内容の要旨
Assembling Support Brackets Support Model Series 700 3 Self tap Bracket screws 1. Locate the four self-tapping screws supplied in your hardware pack (D from Figure 4). Attach the right Attaching Inner Hole Outside of Bracket hand grass catcher support bracket (F1 from Figure 4) using two of the supplied screws in position Support as shown in Figure 13. Place the left hand grass catcher support bracket (F2 from Figure 4) in position Bracket & and secure with the other two screws. 5. I
ページ9に含まれる内容の要旨
Attaching Grass Bags & Grass Bag Cover 1. Place the support tube in position on the rear of unit 4 by sliding the support tube down through the holes in the left side of the bracket assembly. Use the inside hole on the bracket assembly regardless of what size Attaching deck your tractor is equipped with. Refer to Figure 17. Grass Bags 2. Attach the grass bags by hooking them onto the grass bag bracket using the slots in the grass bag and the & Grass Bag tabs on the grass bag bracket as
ページ10に含まれる内容の要旨
Attaching Discharge Chute On Older Model Riders 5 1. On some older models, a clip is already installed on the cutting deck next to the discharge chute opening Attaching in position A, B, or C, as seen in Figure 21. If this is the case, the clip must be removed and a grass Discharge catcher pin installed. Chute 2. Pin Installation: A grass catcher pin (G in Figure 4) and nut (H in Figure 4) have been supplied in All 600 Model Series the hardware pack. First remove the clip, as seen
ページ11に含まれる内容の要旨
Attaching Discharge Chute All Model Series 5 1. Raise the deck to its highest position. Attaching 2. Raise the chute deflector on the deck and hold it while you position the discharge chute over the Discharge chute opening. 3. Place the top rear edge of the discharge chute over Chute the top rear edge of the chute opening. All Model Series 4. Push down on the discharge chute so that its front Retainer Strap bottom edge rolls around the bottom of the deck, then slide the chute forward
ページ12に含まれる内容の要旨
21 6 32 32 34 8 19 Part List: 21 Rear Twin 23 Bagger 10 22 4 34 13 20 15 13 10 10 20 14 7 20 34 18 13 10 12 For parts and/or accessories please call 26 10 1-800-800-7310, or 5 11 1-330-220-4683. 2 25 www.mtdproducts.com 1 35 3 11 33 9 24 30 9 27 33 11 29 31 30 6 16 29 31 28 12
ページ13に含まれる内容の要旨
REF PART NUMBER DESCRIPTION Qty. NO. 1 16587D Support Bracket: Bagger 1 2 16592 Support Tube Assembly 1 6 3 664-04017 Grass catcher Cover Assembly 1 4 710-0597 Screw 1/4-20 x 1” 3 Part List: 5 711-0309A Clevis Pin 1 Rear Twin 6 711-0310 Clevis Pin (on older model tractors) 1 7 711-1421 Clevis Pin 2 Bagger 8 712-0459 Lock Nut 7/16-20 2 9 712-3004A Lock Nut 5/16-18 6 10 712-3027 Hex Flange Lock Nut, 1/4-20 14 11 714-0117 Hairpin Clip 1 12 714-0145 Click Pin 2 13 723-04008A Chute Strap 3 14 731-
ページ14に含まれる内容の要旨
MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by MTD LLC with respect e. MTD does not extend any warranty for products sold or exported to new merchandise purchased and used in the United States, its outside of the United States, its possessions and territories, except possessions and territories. those sold through MTD’s authorized channels of export distribution. “MTD” warrants this product against defects in material and workman- f. Replacement parts tha
ページ15に含まれる内容の要旨
Al propietario Contenido de la caja Ensamblado Listados de piezas Garantía MANUAL DEL OPERADOR Kit de embolsado posterior doble Para tractores cortacésped con plataformas de 38” y 42” Modelos OHD-190-180 IMPORTANTE LEA CON ATENCIÓN LAS REGLAS DE SEGURIDAD E INSTRUCCIONES ANTES DE OPERAR LA UNIDAD FORMULARIO Nº . 769-02302 IMPRESO EN ESTADOS MTD LLC. APARTADO POSTAL 361131 CLEVELAND, OHIO 44136-0019 12/15/2005 UNIDOS DE AMÉRICA
ページ16に含まれる内容の要旨
Este Manual del Operador es una parte importante de su nuevo colector de césped. Le ayudará a montar, preparar y mantener la unidad para obtener los mejores resultados. Por favor, lea y com- prenda el contenido del manual. ÍNDICE 1. Identificación de la podadora tractor ................ Page 3 5. Instalación canal de descarga .........................Page 10 2. Contenido de la caja ........................................ Page 4 6. Lista de piezas .............................................
ページ17に含まれる内容の要旨
Colector de césped Placa de modelo ™ con sistema FastAttach de bolsa doble 1 1 El colector de césped con bolsa doble modelo OEM- 190-180 es un sistema de recogida de césped diseñado para ser usado en todos los tractores cortacésped MTD Identifi - compatibles con plataformas de 38” y 42” (excepto 2001 Yard-Man Revolution/White Outdoor ZTT). cación del Las instrucciones de este manual se dividen en sec- ciones. Lea con atención todas las secciones relativas a modelo de su modelo de poda
ページ18に含まれる内容の要旨
CONTENIDO DE LA CAJA Antes de comenzar la instalación, retire todas las piezas de la caja para asegurarse de que esté todo. El contenido de la caja se enumera más abajo y se muestra en la Figura 3. Los números de pieza de los 2 2 elementos de ferretería se muestran entre paréntesis. Un tubo de canal Un tubo de soporte Un conjunto de canal de descarga Contenido Un conjunto de cubierta de tolva para recorte de césped Dos conjuntos de bolsas para recorte de césped Un soporte de montaje de la ca
ページ19に含まれる内容の要旨
CONTENIDO DEL PAQUETE DE ELEMENTOS DE FERRETERÍA Este juego colector de césped se envía con un paquete de elementos de ferretería. Este paquete de elementos de ferretería puede contener piezas adicionales para realizar la instalación en una podadora tractor diferente de la que usted posee. Por favor, controle el paquete de elementos de ferretería con la siguiente ilustración de acuerdo con su modelo de podadora tractor determinado según se indica en la 2 2 sección 1 de este Manual. Conteni
ページ20に含まれる内容の要旨
Instalación Conjunto de soporte Modelos series 600 a 619 3 3 inclusive IMPORTANTE: Antes del ensamblado, coloque el trac- Instalación tor sobre una superficie firme y nivelada, desenganche Conjunto de la toma de fuerza (PTO), detenga el motor del tractor y coloque el freno de estacionamiento. Retire el soporte 1. Para mayor comodidad, gire el asiento hacia adel- pasador Modelos series 600 a 619 ante y déjelo en esa posición hasta que el colector inclusive de pasto esté totalmente coloca
