ページ1に含まれる内容の要旨
Otraep Or ’s M launa
Twin Rear Bagger - Model No. OEM-190-180A & 19A30002000
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
FORM NO. 769-04317A
03/24/2009
ページ2に含まれる内容の要旨
To The Owner 1 Thank You Thank you for purchasing a double bagging attachment If you have any problems or questions concerning this manufactured by MTD LLC. It was carefully engineered to attachment, phone your local authorized MTD service dealer provide excellent performance when properly operated and or contact us directly. MTD’s Customer Support telephone maintained. numbers, website address and mailing address can be found on this page. We want to ensure your complete satisfaction at a
ページ3に含まれる内容の要旨
Identify The Model of Tractor This manual is designed for installation of this new bagging unit Model Plate on several different models of tractors. It is important for you to determine which model of tractor that you have. Once this is known, follow the pertinent set of instructions on the following pages. Note: Read and observe all WARNING, NOTES and IMPORTANT statements. They are included to provide for the protection of the equipment installer and user, and to ensure the prolonged
ページ4に含まれる内容の要旨
Important Safe Operation Practices 2 WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! DANGER! This attachment was built to be used according to the safe operation practices in
ページ5に含まれる内容の要旨
3. Use slow speed. Choose a low enough speed setting so General Service that you will not have to stop or shift while on the slope. 1. Before cleaning, repairing, or inspecting, make certain the Tires may lose traction on slopes even though the brakes blade(s) and all moving parts have stopped. Disconnect the are functioning properly. Always keep machine in gear spark plug wire and ground against the engine to prevent when going down slopes to take advantage of engine unintended starting
ページ6に含まれる内容の要旨
6 s ce ti On 2 — i Mp Onat rt s eaf Otiepra On p rcatiecs Fold along dotted line (represents a 10° slope) Sight and hold this level with a vertical tree... or a corner of a building... or a fence post 10° Use this page as a guide to determine slopes where you may not operate safely. WARNING! Do not operate your lawn mower with a bagger attachment on such slopes. Do not mow on inclines with a slope in excess of 10 degrees (a rise of approximately six inches every 10 feet). A riding mower with
ページ7に含まれる内容の要旨
Contents of Carton 3 Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Fig. 2-1. Hardware part numbers are shown in parentheses. • Hitch Bracket Kit (3 brackets & Hardware Pack) • Two Grass Bag Assemblies • 700 Series Mount Kit (2 brackets & hardware) • Upper Chute Tube • Chute Tube Extension • Upper Chute Support • Hitch Support • Hinge Cover Pin • Discharge Chute Elbow • Upright Support • Grass Cat
ページ8に含まれる内容の要旨
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with three loose hardware packs enclosed and one hardware pack included in the mounting bracket kit. Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis. Hardware Pack included with 689-00080 Hardware Pack 689-00091 (1) (1) (1) (1) (711-05063) (710-3008) (710-0276) (1) (2) (736-0204) (1) (712-04063) (714-04040) Hardware Pack 689-00087 (2) (1) (4) (710-3008) (711-030
ページ9に含まれる内容の要旨
Assembly & Installation 4 700 Series Tractors Only If you are assembling this bagger unit for use on any model 700 series tractor you will need to install the two tractor mounting brackets packed in your bagger kit. If you are installing this bagger unit on any other tractor, disregard these steps and move to Assemble Mounting Brackets on the next page. To install these brackets on a model 700 series tractor, follow these steps: 1. Install a shoulder bolt from your hardware pack on each br
ページ10に含まれる内容の要旨
Assemble Mounting Brackets To assemble the universal mounting assembly, locate the mounting assembly pack and follow these steps: 1. Attach the two hitch side brackets to the universal rear attachment bracket using four hex bolts and flange lock nuts. With the hooks on the hitch side brackets pointing down, the tabs on the universal rear attachment bracket should be pointing upwards. See Fig. 4-3. Note: This universal mounting bracket assembly is designed to work with other available atta
ページ11に含まれる内容の要旨
Assembling The Support Assembly Locate the upright support bracket and the bag support assembly. Assemble it by following these steps: 1. Lay the bag support assembly topside down with the mounting bracket portion facing upwards. 2. Insert the notched end of the vertical support bracket into the bag support assembly, as in Fig. 4-5, and secure with a 5/16-18 carriage bolt and 5/16-18 flange lock nut. See Fig. 4-6. Figure 4-7 2. Install the clevis pin from hardware pack 689-00087 into the t
ページ12に含まれる内容の要旨
3. Install the bagger hanger assembly onto the mounting Assembling Remaining Bagger Components assembly on the tractor by hooking it over the hitch plate Now that the mounting brackets are assembled and are in place between the two tabs. See Fig. 4-9. on the tractor, follow these steps to assemble the remaining bagger components. 1. Snap the plastic upper chute support in place by first clipping the side portion onto the bagger support rail with the edge of the snap feature aligned with th
ページ13に含まれる内容の要旨
3. Install the bagger screen into the bagger cover by first inserting the end closest to the side with the cutout into the mounting hole, as in Fig. 4-12. Make sure to feed the screen under the lip, as in Fig. 4-13. Figure 4-14 Figure 4-12 4. Clip in the other side by pushing the screen into the provided cutout. See Fig. 4-13. Figure 4-15 Make sure screen sits under the cover’s lip Figure 4-13 5. Install the bagger cover onto the bag support assembly, as seen in Fig. 4-14. The plastic co
ページ14に含まれる内容の要旨
7. Open Hood by pushing in on the rear, right-side tab with your right hand, as seen in 1 of Fig. 4-17, and lifting the cover with your left hand in the center rear of the bagger cover, 2. 2 1 Figure 4-19 Figure 4-17 8. Install both bag assemblies with the tight mesh sides facing forward, onto the bag support brackets by inserting the front edge in first, as seen in Fig. 4-18, and setting the back edge down until it fits into the assembly. 1 Figure 4-20 2 Figure 4-18 9. Install the rubber c
ページ15に含まれる内容の要旨
Note: For the chute elbow to be properly installed, the 13. Install the chute adapter onto the chute elbow by lining up bottom edge must fall over the bottom of the deck the tabs and sliding the adapter over the chute elbow, as opening. See Fig. 4-22. in Fig. 4-24. Secure the chute adapter by installing the two ratchet clips included in the hardware pack in the holes provided. Figure 4-22 12. Secure the chute elbow to the tractor’s deck by hooking the chute strap onto the ball pin installe
ページ16に含まれる内容の要旨
Operation 5 Bagger Usage NOTE: When both grass bags are full, place the tractor on a firm, level surface, disengage the PTO, turn the tractor engine off and set the parking brake. 1. Flip Seat up. 2. Lift up grass bag cover as instructed on Page 14 in Step 7. Do not remove the chute tube assembly from the tractor. 3. Remove the grass bags by lifting these up and moving the bags away from the bag support assembly. 4. Empty the grass clippings at a proper disposal sight, use the handle at the
ページ17に含まれる内容の要旨
MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by MTD LLC with b. Routine maintenance items such as lubricants, filters, blade respect to new merchandise purchased and used in the United States sharpening, tune-ups, brake adjustments, clutch adjustments, and/or its territories and possessions, and by MTD Products Limited deck adjustments, and normal deterioration of the exterior finish with respect to new merchandise purchased and used in Canada and/ due to
ページ18に含まれる内容の要旨
M launa led Odraep Or Embolsadora trasera doble - Modelo Nº OEM-190-180A ADVERTENCIA LEA Y SIGA TODAS LAS INSTRUCCIONES DE ESTE MANUAL ANTES DE PONER EN FUNCIONAMIENTO ESTA MÁQUINA. SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES. MTD LLC. APARTADO POSTAL 361131 CLEVELAND, OHIO 44136-0019 Impreso en Estados Unidos de América
ページ19に含まれる内容の要旨
Al propietario 1 Gracias Gracias por comprar un accesorio embolsador doble fabricado no se apliquen a todos los modelos. MTD LLC se reserva el por MTD LLC. El mismo ha sido diseñado cuidadosamente derecho de modificar las especificaciones de los productos, los para brindar excelente rendimiento si se lo opera y mantiene diseños y el equipo sin previo aviso y sin generar responsabilidad correctamente. por obligaciones de ningún tipo. Por favor lea todo este manual antes de hacer funcionar el
ページ20に含まれる内容の要旨
Identifique el modelo de tractor Este manual está destinado a la instalación de la nueva unidad Placa de modelo embolsadora en varios modelos distintos de tractor. Es importante que usted determine el modelo de tractor que tiene. Una vez identificado, siga el conjunto de instrucciones pertinentes en las páginas siguientes. Nota: Lea y observe todas las ADVERTENCIAS, NOTAS y declaraciones IMPORTANTES. Se las ha incluido para proporcionar protección al instalador y al usuario del equipo
