ページ1に含まれる内容の要旨
®
Operator’s Manual
MODEL
214 IP
216 IP
214 KW
216 KW
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
Warning:
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In
ページ2に含まれる内容の要旨
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR LAWN MOWER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL, HEED ITS WARNING. WARNING: The Engine Exhaust from this product contains chemicals known to the Sta
ページ3に含まれる内容の要旨
• Do not engage the self-propelled mechanism on • Always be sure of your footing. A slip and fall can units so equipped while starting engine. cause serious personal injury. If you feel you are losing your balance release the blade control • The blade control handle is a safety device. Never handle immediately and the blade will stop in less attempt to bypass its operation. Doing so makes than 3 seconds. the safety device inoperative and may result in personal injury through contact with the rot
ページ4に含まれる内容の要旨
• Never run an engine inside a closed area. Exhaust • Keep all nuts, bolts, and screws tight to be sure the gases contain carbon monoxide. This odorless gas equipment is in safe working condition. can be deadly when inhaled. • Never tamper with safety devices. Check their • When filling the fuel tank, stop when the gasoline proper operation regularly. reaches one inch from the top. This space must be • After striking a foreign object, stop the engine, left for expansion. Do not overfill. remove
ページ5に含まれる内容の要旨
FOLD ON DOTTED LINE, REPRESENTING A 15° SLOPE USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY. SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST 15° WARNING Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your f
ページ6に含まれる内容の要旨
SECTION 1: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new walk behind. It will help you assemble, prepare and maintain your walk behind. Please read and understand what it says. Before you start to prepare your walk behind for its first use, please locate the model plate and copy the information from it in this Operator’s Manual. The information on the model plate is very important if you need help from your dealer or customer support department. • Every wal
ページ7に含まれる内容の要旨
SECTION 3: SET-UP INSTRUCTIONS ITEMS REQUIRED FOR ASSEMBLY • 7/16" and 1/2" wrench or socket • Motor Oil (SAE 10W30) •Fresh Gasoline IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL (unless carton is marked as “audit machine”) in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your mower. NOTE: Reference to right or left hand side of the mower is observed from the operating position. SET-UP YOUR LAWN MOWER Follo
ページ8に含まれる内容の要旨
Step 3. Replace the hardware removed from the Step 4. Raise the complete handle assembly lower handle. Tighten all four handle until it lines up with one of the mounting (two on each side of the handle holes in the struts. Put the carriage bolt assembly) nuts with 1/2" wrench or through the struts and then through the socket. handle. Place the saddle washer on the bolt and then fasten with the wing nut by hand. Complete this step by attaching the other side of the handle to the other
ページ9に含まれる内容の要旨
Step 5. Attach control cables to handle with pull ties found on the handle. HERE Step 6. Loosen the nut holding the rope guide to the upper handle with a 7/16" wrench or socket. Step 7. Squeeze the blade control bail against the upper handle and pull out starter rope, slowly! . (Models without BBC) Step 8. Thread starter rope into rope guide. Step 9. Tighten nut. SQUEEZE Blade Control Bail Nut Upper Handle Look Here Starter Rope Rope Guide 9
ページ10に含まれる内容の要旨
SECTION 4: CONTROLS Blade Control Bail Drive Clutch Control Bail Blade Brake Control Throttle Control Recoil Starter BLADE BRAKE CONTROL MODEL ENGINE BRAKE CONTROL MODEL Figure 2 BLADE CONTROL BAIL For units equipped with Engine Brake Control: The blade control bail is located on the handle of the mower. See Figure 2. The blade control bail must be depressed in order to start and operate the unit. Release the blade control bail to stop the engine and blade. For units equipped with Blade Brake
ページ11に含まれる内容の要旨
WARNING: Shift lever only with the engine running. Shifting with the Drive Clutch Control engaged can damage the transmission. CUTTING HEIGHT ADJUSTMENT LEVERS The cutting height adjustment levers are located above each wheel. Cutting heights are from 3/4” to 4-1/2" with 3/8" increments. The low range setting is 3/4" to 2-5/8” and the high range setting is from 2-5/8” to 4-1/2”. To adjust the cutting height, push the levers away from the mower and then move it forward or back for a new cutting h
ページ12に含まれる内容の要旨
EACH TIME BEFORE YOU START YOUR MOWER • Attach spark plug wire to spark plug. Make certain the metal cap on the end of the spark plug wire is fastened securely over the metal tip on the spark plug. TO START ENGINE AND ENGAGE BLADE • Move the throttle control lever all the way forward. (This will activate choke on some models). • Prime engine as instructed in the separate engine manual. (If required). • For engine brake models only. Stand behind the unit, squeeze and hold the blade control handl
ページ13に含まれる内容の要旨
BAGGING GRASS CLIPPINGS This mower can bag grass clippings. Follow steps 1 and 2 to ready the mower for bagging. Step 1. Remove mulching plug, if installed. Step 2. Hang grass bag on mower. HERE LIFT PULL EMPTYING A FULL BAG OF GRASS Once the grass bag is full it will need to be emptied, follow steps 3 and 4 to empty the grass bag. Step 3. Lift flap and pull bag away from mower. Step 4. Lift bag up and away from mower. Dump the grass clippings. LIFT PULL LIFT MULCHING GRASS CLIPPINGS This m
ページ14に含まれる内容の要旨
SIDE DISCHARGING GRASS CLIPPINGS (Optional) Step 1. Lift rear flap, remove grass bag, or Side Discharge Top and Left View. mulch plug if installed,. Hang side This side up discharge chute. Hang LIFT SECTION 6: ADJUSTMENTS WARNING: Do not at any time make any adjustment to lawn mower without first stopping engine and disconnecting spark plug wire. HANDLE HEIGHT ADJUSTMENT • See the ASSEMBLY SECTION for handle height adjustment. THROTTLE CONTROL ADJUSTMENT • See the engine manufacturers manual
ページ15に含まれる内容の要旨
SECTION 7: LUBRICATION WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or doing any kind of work on the lawn mower. Blade Control Handle LUBRICATE Axle Shafts Wheels Engine SEE ENGINE MANUAL Figure 4 Blade Control: Lubricate the pivot points on the blade control handle and the brake cable at least once a season with light oil. See Figure 4. The blade control must operate freely in both directions. Wheels: The wheels are equipped with sealed ball bearings
ページ16に含まれる内容の要旨
DECK The underside of the mower deck should be cleaned after each use to prevent a buildup of grass clippings, leaves, dirt or other matter. If this debris is allowed to accumulate, it will invite rust and corrosion, and may prevent proper mulching, discharge or bagging. The deck may be cleaned by tilting the mower and scraping clean with a suitable tool (make certain the spark plug wire is disconnected). CUTTING BLADE REMOVAL, REPLACEMENT AND SHARPENIN BLADE BOLT BLADE BOLT (Blade Brake (Engin
ページ17に含まれる内容の要旨
SECTION 9: OFF-SEASON STORAGE The following steps should be taken to prepare lawn mower for storage. • Clean and lubricate mower thoroughly as described in the lubrication instructions. • Refer to engine manual for correct engine storage instructions. • Coat mower’s cutting blade with chassis grease to prevent rusting. • Store mower in a dry, clean area. Do not store next to corrosive materials, such as fertilizer. NOTE: When storing any type of power equipment in an poorly ventilated or metal
ページ18に含まれる内容の要旨
EQUIPMENT TWO-YEAR LIMITED WARRANTY This warranty is specific to the product manual it is attached to. For a complete list of products and warranties contact your MTD Pro dealer. Proper maintenance of your MTD Pro equipment is the owner’s responsibility. Follow the instructions in your owner’s manual for correct lubricants and maintenance schedule. Your MTD Pro dealer carries a complete line of quality lubricants and filters for your equipment’s engine, transmission, chassis and attachments. 1
