ページ1に含まれる内容の要旨
IMI CORNELIUS INC One Cornelius Place Anoka, MN 55303-6234
Telephone (800) 238-3600 Facsimile (612) 422-3246
FCB (SOLID-STATE) POST-
MIX DISPENSER
TWO-FLAVOR/HOT-GAS DEFROST
WITH V3 ELECTRONICS
Service Manual
Part No. 326142000
April 24, 1989
Revised: February 10, 1992
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
This Manual must be read and understood before installing or operating this equipment
PRINTED IN U.S.A
IMI CORNELIUS INC; 1989–92
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Page GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 UNIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 THEORY OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DEFROS
ページ3に含まれる内容の要旨
TABLE OF CONTENTS (cont’d) Page ADJUSTING ‘‘VIS SET’’ (PRODUCT VISCOSITY) OF DISPENSED PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 DISPLAYED EVAPORATOR REFRIGERATION COILS INLETS AND COMMON OUTLET SENSORS TEMPERATURES . . . . . . . . . . . . . . . . . . . . 15 ‘‘VOLTAGE’’ (DISPLAYED VOLTAGE READOUT) . . . . . . . . . . . . . . . . . . . . . . 15 PROGRAMMING COMPONENTS ‘‘DIAGNOSE’’ (DIAGNOSTIC MODE) INTO UNIT . . .
ページ4に含まれる内容の要旨
TABLE OF CONTENTS (cont’d) Page PROGRAMMING ‘‘DEFROST’’ (AUTOMATIC) SETTINGS INTO UNIT . . 24 PROGRAMMING ‘‘SLEEP’’ (SLEEP TIME) INTO UNIT . . . . . . . . . . . . . . . . . 24 PROGRAMMING ‘‘WAKE UP’’ (WAKE UP) TIME INTO UNIT . . . . . . . . . . . . 24 PROGRAMMING POINT OF SALE MESSAGE DISPLAY . . . . . . . . . . . . . . . 24 ADJUSTING ‘‘VIS SET’’ (PRODUCT VISCOSITY) OF DISPENSED PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ5に含まれる内容の要旨
TABLE OF CONTENTS (cont’d) Page PROGRAMMING ‘‘SLEEP’’ (SLEEP TIME) INTO UNIT . . . . . . . . . . . . . . . . . 38 PROGRAMMING ‘‘WAKE UP’’ (WAKE UP TIME) INTO UNIT . . . . . . . . . . . . 39 PROGRAMMING POINT OF SALE MESSAGE DISPLAY . . . . . . . . . . . . . . . 41 ADJUSTING “VIS SET” (PRODUCT VISCOSITY) OF DISPENSED PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 ‘‘VIS READ’’ (ACTUAL VISCOSITY READOUT) OF PRODUCT IN FRE
ページ6に含まれる内容の要旨
TABLE OF CONTENTS (cont’d) Page ALL FAULT MESSAGES NOT OPERATING. . . . . . . . . . . . . . . . . . . . . . . . . . . 62 ‘‘CO2 OUT’’ FAULT MESSAGE GOES ON DURING OPERATION. . . . . . . . 63 ‘‘H2O OUT’’ FAULT MESSAGE GOES ON DURING OPERATION. . . . . . . . 63 ‘‘SYRUP 1’’ OR ‘‘SYRUP 2’’ FAULT MESSAGE GOES ON DURING OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 ‘‘ERROR 1’’ OR ‘‘ERROR2’’ FAULT MESSAGE GOES ON DURING OPERATIO
ページ7に含まれる内容の要旨
TABLE OF CONTENTS (cont’d) Page LIST OF FIGURES (CONT’D) FIGURE 12. WATER STRAINER SCREEN AND DOUBLE LIQUID CHECK VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 FIGURE 13. CO2 GAS CHECK VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 FIGURE 14. BEATER DRIVE MOTOR AND SHAFT SEAL ASS’Y REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ8に含まれる内容の要旨
GENERAL INFORMATION IMPORTANT: To the user of this manual - This manual is a guide for installing, operating, and maintaining this equipment. Refer to Table of Contents for page location of information pertaining to questions that arise during installation, operation, service and maintenance, or troubleshooting this equipment. GENERAL DESCRIPTION This section gives the description, theory of operation, and design data for the FCB Solid-State Post-Mix Two-Flavor Dispenser with Hot-Gas Defrost (he
ページ9に含まれる内容の要旨
Table 1. Design Data (cont’d) Table 1. Design Data (cont’d) Overall Dimensions: Overall Dimensions: Height 60-1/2 inches Width 19-1/4 inches Depth Without Drip Tray 32-1/2 inches Depth With Drip Tray 38 inches Shipping Weight (approx.) 466 pounds Compressor Horsepower 2 H.P. Refrigeration System: Refrigeration System: Refrigerant Type R-502 Refrigerant Charge See Unit Nameplate Ambient Operating Temperature 40° F to 100° F Electrical Requirements: Electrical Requirements: 60 Hz Unit: Operati
ページ10に含まれる内容の要旨
MANUAL DEFROST SYSTEM The Manual hot-gas defrost system may be activated at any time by pressing ‘‘DEFROST’’ switch on front of Unit. Refrigeration compressor will operate for a short time, then both freeze cylinders will go into defrost and defrost for approximately 60-seconds. At end of manual defrost cycle, Unit will return to normal operation. Manual defrost may be cancelled at any time by pressing ‘‘CANCEL DEFROST’’ switch. AUTOMATIC DEFROST SYSTEM The automatic hot-gas defrost system may b
ページ11に含まれる内容の要旨
PRODUCT SAMPLE VALVE (2) PRODUCT BLENDER TANK (2) CARBONATOR TANK PRODUCT SHUTOFF SYRUP FLOW VALVE (2) REGULATOR (2) FREEZE CYLINDER (2) CARBONATED WATER FLOW REGULATOR (2) FREEZE CYLINDER CARBONATED WATER OVERFLOW TUBE SOLENOID VALVE (2) LIQUID CHECK SYRUP SYRUP VALVE (4) SOLENOID V SOLENOID VA AL LVE (2) VE (2) CARBONATED WATER VOLUME SAMPLE VALVE PRIMARY CO 2 REGULATOR SYRUP SOLD-OUT ASS’Y DOUBLE LIQUID FLOAT SWITCH (2) CHECK VALVE SECONDARY CO 2 REGULATOR TO *WATER CARBONATOR PRESSURE SHUTOF
ページ12に含まれる内容の要旨
INSTALLATION This section covers unpacking and inspection, installing LOOSE-SHIPPED PARTS, selecting location, installing Unit, preparing for operation, and operation. UNPACKING AND INSPECTION (see Figure 5) NOTE: The Unit was thoroughly inspected before leaving the factory and the carrier has accepted and signed for it. Any damage or irregularities should be noted at time of delivery (or not later than 15 days from date of delivery) and immediately reported to the delivering carrier. Request a
ページ13に含まれる内容の要旨
2. SPANNER WRENCH, FLOW REGULATORS (item 2) is used to adjust flow regulators inside Unit. 3. SPANNER WRENCH, DISPENSING VALVE (item 3) is used to remove shank nuts securing dispensing valves to faceplates. 4. CLEANING BRUSH (item 4) is used to clean faceplate relief valves passages. 5. TAPERED GASKET, BLACK (item 5) is used to seal connection when connecting plain water source line to Unit water inlet line. 6. DRIP TRAY SUPPORTS (item 8) to be installed on front of Unit and secured with THREAD
ページ14に含まれる内容の要旨
7 326142000 10. Valve Lever 1. Product Inlet Fitting 19. Power Coupler (plastic) 11. Knob 2. Scraper Blade (2) 20. Beater Motor Drive Shaft 12. Dispensing Valve 21. Beater Drive Motor Shaft Coupling 3. Evaporator Coi.l 13. Beater 4. Relief Valve Port 22. Beater Drive Motor 14. Drive Shaft Seal Assembly 5. O-Ring 23. Unit Frame 15. Allen Head Setscrew 6. Flatwasher (4) 24. Drive Shaft Assembly 16. Beater Shaft Coupling 7. Hex Nut (4) 25. Viscosity Sensor 17. Drive Pin 8. Faceplate 26. Spinner
ページ15に含まれる内容の要旨
BEATER KEY ON END KEY ON END OF POST OF POST KEY SLOT ON BLADE SCRAPER BLADES MUST BE MOUNTED TO THE BEATER BODY AS SHOWN USING THE PERFO- RATED EDGE AS THE LEADING EDGE. LINE UP KEY ON END OF POSTS WITH KEY SLOT IN SCRAPER BLADES. FIGURE 4. BEATERS AND SCRAPER BLADES INSTALLATION A properly grounded 219 to 242 VAC, 60Hz single-phase electrical circuit with a 30-amp minimum-rated disconnect switch (not provided) fused at 30 amps (slo-blow) or circuit connected through an equivalent HACR circuit
ページ16に含まれる内容の要旨
1. Close to a plain water inlet supply line with a minimum pressure of 12-psig. NOTE: Circulating air, required to cool the refrigeration system’s condenser coil, is drawn in through grille on front and exhausted out through sides and back of Unit. Restricting air circulation through the Unit will decrease its cooling efficiency. 2. When installing Unit, do not allow obstruction to block grille on front which will block off air intake to inside of Unit. If installation dictates only one side or
ページ17に含まれる内容の要旨
WARNING: CO displaces oxygen. Strict attention must be observed in the prevention of 2 CO (carbon dioxide) gas leaks in the entire CO and soft drink system. If a CO gas leak is 2 2 2 suspected, particularly in a small area, immediately ventilate the contaminated area before attempting to repair the leak. Personnel exposed to high concentration of CO gas will experience 2 tremors which are followed rapidly by loss of consciousness and suffocation. 1. Unscrew protector cap (with chain attached) f
ページ18に含まれる内容の要旨
CONNECTING ELECTRICAL POWER CIRCUIT TO UNIT (see Figure 17) WARNING: Make sure Unit 30-amp minimum-rated disconnect switch (not provided) or equivalent HACR circuit breaker is in ‘‘OFF’’ position. Domestic Unit. IMPORTANT: Power circuit voltage across L and L terminals on contactor inside lower control box, 1 2 with refrigeration compressor operating, must be in operating range of between 219 and 242 VAC, 60Hz single-phase range for proper operation. If voltage is below or above this range, a
ページ19に含まれる内容の要旨
TURNING ON ELECTRICAL POWER TO UNIT Turn on electrical power to Unit. Operational status of Unit is now being displayed as fault messages on control panel message display. The following fault messages will be continuously displayed at 2-second intervals until necessary operation requirements are satisfied. ‘‘OFF 1’’ (Beater Motor No. 1 not operating) ‘‘OFF 2’’ (Beater Motor No. 2 not operating) ‘‘H O OUT’’ (No water supply to Unit) 2 ‘‘CO OUT’’ (No CO gas supply to Unit) 2 2 ‘‘SYRUP 1’’ (No syru
ページ20に含まれる内容の要旨
IMPORTANT: The following CO and liquid disconnects disconnecting and connecting procedure for 2 soft drink tank replacement or filling soft drink tank in place must be performed in order as follows: To disconnect soft drink tank from Unit syrup system. A. Disconnect liquid disconnect from soft drink tank. NOTE - Disconnecting liquid quick disconnect from soft drink tank first prevents syrup from backflowing through Unit syrup flow regulator which may alter regulator adjustment. B. Second, discon
