ページ1に含まれる内容の要旨
Operator’s Manual
20” Rotary Lawn Mower
Models 020
021
022
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in eff
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Content Page Important Safe Operation Practices................................................................... 3 Slope Gauge...................................................................................................... 6 Hardware Pack .................................................................................................. 7 Assembling Your Lawn Mower........................................................................... 7 Know Your Lawn Mower .........
ページ3に含まれる内容の要旨
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol—HEED ITS WARNING. WARNING: The Engine Exhaust from this product contains chemicals known to the Stat
ページ4に含まれる内容の要旨
discharge cover, grass catcher, blade control handle or 5. Keep children away from hot or running engines. They other safety protective devices in place and working. can suffer burns from a hot muffler. Never operate mower with damaged safety devices. 6. Never allow children under 14 years old to operate a Failure to do so, can result in personal injury. power mower. Children 14 years old and over should 14. Muffler and engine become hot and can cause a burn. Do read and understand the opera
ページ5に含まれる内容の要旨
3. Check the blade and engine mounting bolts at frequent adjustment while the engine is running. intervals for proper tightness. Also, visually inspect blade 9. Grass catcher components, discharge cover, and trail for damage (e.g., bent, cracked, worn) Replace blade shield are subject to wear and damage which could with the original equipment manufacture’s (O.E.M.) blade expose moving parts or allow objects to be thrown. For only, listed in this manual. “Use of parts which do not safety prote
ページ6に含まれる内容の要旨
SECTION 2: SLOPE GAUGE Use this page as a guide to determine slopes where you may not operate the lawn mower safely. 6 USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY. SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST 15° WARNING Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. If operating a walk-b
ページ7に含まれる内容の要旨
SECTION 3: HARDWARE PACK Group 2 Group 4 Group 5 Group 1 Group 6 Group 3 SECTION 4: ASSEMBLING YOUR LAWN MOWER NOTE: This operator’s manual covers various models of mowers. Follow only those instructions which pertain to your unit. Bolt Spark Plug Wire Tools Required A set of adjustable wrenches or individual wrenches of the following sizes:7/16”, 1/2”, 9/16”, 3/4”. NOTE: Reference to right or left hand side of the mower is observed from the operating position. Spark Plug WARNING: The chute
ページ8に含まれる内容の要旨
Install the hex screws, shoulder screws and flange Route the cable under the lower handle. nuts from group 4 of the hardware pack. Using two On the opposite end of the cable housing is a snap 1/2” wrenches, tighten securely. See Figure 2. fitting. The shaft inside the snap fitting fits in the second hole on the upper handle. Press the snap fitting in place as shown in Figure 4. Make sure that the blade control handle is on top of the upper Lower Handle handle. Attaching Blade Cont
ページ9に含まれる内容の要旨
Block the mower securely. Using hardware from group 1 of the hardware pack, place axle bolt through the wheel with the hub side of the wheel facing the deck. See Figure 8. Place the small bell washer on the axle bolt with the crown side towards the wheel. See Figure 8. Secure the wheel to the deck with the large bell washer and the nut. Repeat on other sides. Z Fitting Remove blocks and put the mower on ground. Attaching Chute Deflector Figure 6 Align the holes on the ch
ページ10に含まれる内容の要旨
Know Your Lawn Mower Compare the illustration in Figure 11 Figure 11with your Blade Control lawn mower to familiarize yourself with the location of Handle various controls and adjustments. Throttle Control Recoil Starter The mower engine is equipped with a constant speed Engine throttle, which is set at full throttle for best performance. Blade Control Handle The blade control handle is located on the upper handle Spark Plug of the mower.The blade control handle must be depressed in order t
ページ11に含まれる内容の要旨
For a healthy lawn, never cut more than one-third of Using Your Lawn Mower the total length of the grass at any one cutting. This mower is designed to operate at full throttle. WARNING: Never operate your unit without either the rear deflector or entire grass catcher WARNING: If you strike a foreign object, assembly in place. stop the engine. Remove wire from spark plug, thoroughly inspect the mower for any Make sure that lawn is clear of stones, sticks, wire, damage, and repair t
ページ12に含まれる内容の要旨
Wheels To balance blade The wheels require no lubrication. However, if the When sharpening the blade, follow original angle of wheels are removed for any reason, lubricate the grind as a guide. It is extremely important to grind surface of the axle bolt and the inner surface of the off all edges equally to keep the blade balanced. wheel with light oil. Engine oil may also be used. NOTE: An unbalanced blade will cause excessive When tipping the unit, empty the fuel tank and keep vibration
ページ13に含まれる内容の要旨
SECTION 8: OFF-SEASON STORAGE The following steps should be taken to prepare lawn Store mower in a dry, clean area. Do not store next mower for storage. to corrosive materials, such as fertilizer. Clean and lubricate mower thoroughly as described NOTE: When storing any type of power equipment in in the lubrication instructions. an unventilated or metal storage shed, care should be Refer to engine manual for correct engine storage taken to rust-proof the equipment. Using a light oil or
ページ14に含まれる内容の要旨
SECTION 10: PARTS LIST FOR MODEL SERIES 020 5 4 27 26 15 18 19 21 19 20 3 29 16 23 22 17 7 24 29 28 16 25 1 28 22 23 24 6 24 22 23 15 28 14 25 2 10 28 12 24 30 23 11 13 22 9 8 14
ページ15に含まれる内容の要旨
Model Series 020 Ref. Part No. Description No. 710-0654A Hex Ind. Washer Screw 3/8-16 x 1.0 1. 782-0048 Cutting Deck: 20” 2. 749-04037 Lower Handle 3. 749-1092A Upper Handle 4. 747-1161A Control Handle (Bail) 5. 731-0872A Rear Flap 6. 17098 Hinge Clip 7. 710-1044 Screw 3/8-24 x 1.5” Group 8 8. 936-0524A Blade Bell Support 9. 748-0376C Blade Adapter 10. 742-0640 Cutting Blade 11. 731-0064 Discharge Chute 12. 710-0932 Carriage Screw 1/4-20 x 1.0” 13. 736-0173 Flat Washer 14. 712-0324 Lock Nut 1/
ページ16に含まれる内容の要旨
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD LLC with d. MTD LLC does not extend any warranty for products respect to new merchandise purchased and used in the sold or exported outside of the United States, its United States, its possessions and territories. possessions and territories, except those sold through MTD LLC’s authorized channels of export distribution. MTD LLC warrants this product against defects for a period of e. Parts that are not
