ページ1に含まれる内容の要旨
Table of Contents
Powered Rakes
PR1660, PR1672 & PR1690
24503
314-216M
Operator’s Manual
Read the Operator’s manual entirely.
When you see this symbol, the
subsequent instructions and
!
warnings are serious - follow without
exception. Your life and the lives of
others depend on it!
10/20/06
© Copyright 2006 Printed
Cover photo may show optional
equipment not supplied with
standard unit.
ページ2に含まれる内容の要旨
Land Pride Table of Contents Table of Contents Important Safety Information . . . . . . . . . . .1 Section 4: Maintenance & Lubrication . .16 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Look For The Safety Alert Symbol . . . . . . . . . . . . . 1 Slip Clutch Maintenance . . . . . . . . . . . . . . . . . . .16 Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Slip Clutch with
ページ3に含まれる内容の要旨
REMOVE Land Pride Table of Contents Important Safety Information Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Look For The Safety Alert Symbol Thoroughly read and understand The SAFETY ALERT SYMBOL indicates there is a the instructions given in this potential hazard to personal safety involved and extra manual before operation. Refer to safety precaution must be taken. When you see this t
ページ4に含まれる内容の要旨
Land Pride Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Use the following maximum Use Safety Transport speed - tow load weight ratios as Lights and Devices Machinery Safely a guideline: 20 mph when weight is less Slow moving tractors, self- Comply with state and local laws. propelled equipment and towed than or equal to the weight of Maximum transport speed for tractor. implements can
ページ5に含まれる内容の要旨
Land Pride Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Avoid High Wear Prepare for Emergencies Pressure Fluids Hazard Protective Equipment Be prepared if a fire starts. Escaping fluid under pressure can Protective clothing and equipment Keep a first aid kit and fire penetrate the skin causing serious should be worn. extinguisher handy. injury. Wear clothing and equipment Keep emergen
ページ6に含まれる内容の要旨
Land Pride Table of Contents Important Safety Information 4. Refer to this section for proper label placement. Safety Labels To install new labels: Your Powered Rake comes equipped with all safety a. Clean the area the label is to be placed. labels in place. They were designed to help you safely b. Spray soapy water on the surface where the label is to operate your implement. Read and follow their be placed. directions. c. Peel backing from label. Press firmly onto the surface. 1. Keep all safet
ページ7に含まれる内容の要旨
Land Pride Table of Contents Important Safety Information 818-230C Red Reflector 23504 818-230C Red Reflector (PR1690 only) 23504 818-229C Amber Reflector (PR1690 only) 23503 10/20/06 PR1660, PR1672 & PR1690 Powered Rakes 314-216M 5
ページ8に含まれる内容の要旨
Land Pride Table of Contents Important Safety Information 838-111C 23503 Danger: Moving Parts ROTATING DRIVELINE KEEP AWAY! 818-552C 23504 Danger: Rotating Driveline 818-130C Caution: 540 RPM 24503 6 PR1660, PR1672 & PR1690 Powered Rakes 314-216M 10/20/06
ページ9に含まれる内容の要旨
Land Pride Table of Contents Important Safety Information 838-094C Warning: High Pressure Fluid Hazard 23504 818-552C ROTATING DRIVELINE Danger: Rotating Driveline KEEP AWAY! 24503 818-540C Danger: Guard Missing Located under driveline shields 24503 10/20/06 PR1660, PR1672 & PR1690 Powered Rakes 314-216M 7
ページ10に含まれる内容の要旨
Land Pride Table of Contents Introduction Introduction Land Pride welcomes you to the growing family of new If customer service or repair parts are required contact a product owners. This Powered Rake has been designed Land Pride dealer. A dealer has trained personnel, repair with care and built by skilled workers using quality parts and equipment needed to service the Powered materials. Proper assembly, maintenance and safe Rake. operating practices will help you get years of satisfactory The p
ページ11に含まれる内容の要旨
Land Pride Table of Contents Section 1: Assembly and Set-Up Section 1: Assembly and Set-Up 2. Slowly back the tractor up to the Powered Rake and Tractor Requirements use the tractor’s 3-point hydraulic control to align the Tractor horsepower and weight must be capable of lower hitch link holes with the clevis lug holes on the controlling the Powered Rake under all operating Powered Rake. conditions. Tractors outside the horsepower range must 3. Engage tractor park brake, shut tractor engine off
ページ12に含まれる内容の要旨
Land Pride Table of Contents Section 1: Assembly and Set-Up 3. The driveline will require shortening if it is too long to PTO Hook-Up fit between tractor and Powered Rake. Shorten If the Powered Rake is to be used on more than one driveline as follows: tractor, an additional PTO shaft may be required - a. Raise 3-point lower arms until Powered Rake and especially if a quick hitch is used. tractor PTO shafts are approximately level with each other. Securely block Powered Rake frame in ! this posi
ページ13に含まれる内容の要旨
Land Pride Table of Contents Section 1: Assembly and Set-Up IMPORTANT: A small chain is supplied with the driveline. This chain must be attached to the inner driveline shield and to the Powered Rake to restrict shield rotation. 5. Hook driveline safety chain in the hole in the inner driveline guard. Attach the other end to the Powered Rake’s main frame. 6. Start tractor and raise Powered Rake just enough to remove blocks used to support the deck in step 3a. 7. Slowly engage the tractor’s hydraul
ページ14に含まれる内容の要旨
Land Pride Table of Contents Section 2: Operating Section 2: Operating 4. Inspect hydraulic hoses for wear, damage and Operating Check List hydraulic leaks. See “Avoid High Pressure Fluids Hazard” Hazard control and accident prevention are dependent on page 3. Replace damaged and worn hoses with upon the awareness, concern, prudence and proper genuine Land Pride parts. training involved in the operation, transport, 5. Set tractor throttle to idle or slightly above idle and maintenance and storag
ページ15に含まれる内容の要旨
Land Pride Table of Contents Section 2: Operating allows more clods, rocks and debris to pass over the Operating Instructions continued roller and produces a coarser soil finish. First completely familiarize yourself with the Operator’s Manual. Then complete the Operator’s checklist, Set the working depth and level the rake at the caster properly attach the Powered Rake to your tractor, make gauge wheels and not with the tractor. Normally a one- initial depth setting, level settings and roller a
ページ16に含まれる内容の要旨
Land Pride Table of Contents Section 3: Adjustments Section 3: Adjustments Gauge Wheels Rake Angle The roller frame can be angled a maximum of 15 degrees Refer to Figure 3-1 in either direction for windrowing material to the side. Caster type gauge wheels are mounted on the rake to Angling is accomplished with either a hydraulic cylinder control roller height during field operation. Do not use or a ratchet jack. tractor to control roller height. Adjust rake angle with a ratchet jack by setting t
ページ17に含まれる内容の要旨
Land Pride Table of Contents Section 3: Adjustments Drive Chain Adjustment End Plates Refer to Figure 3-3 Refer to Figure 3-4 End plates (#1) & (#2) are utilized to collect rocks and debris in front of the roller for the purpose of distributing ! CAUTION material over low areas. They can be removed and BEFORE any maintenance is performed, lower the Powered stored on the right hand side of the rake by removing the Rake to the ground, stop tractor engine and remove ignition key. linch pins (#3) co
ページ18に含まれる内容の要旨
Land Pride Table of Contents Section 4: Maintenance & Lubrication Section 4: Maintenance & Lubrication Maintenance Slip Clutch Maintenance Proper servicing and adjustment is the key to the long life Slip clutches should be “run-in” prior to initial operation of any implement. With careful and systematic inspection, and after long periods of inactivity. To prevent driveline you can avoid costly maintenance, time and repair. and gearbox damage, repeat “Run-In” instructions at the beginning of each
ページ19に含まれる内容の要旨
Land Pride Table of Contents Section 4: Maintenance & Lubrication Slip Clutch with Hex Head Bolts If your clutch has exposed friction disks and is tensioned with hex head bolts as shown in Figure 4-4, follow clutch run-in and assembly instructions below. If your clutch has enclosed friction disks and is tensioned with hex socket bolts as shown in Figure 4-1 on page 16, follow instructions for “Slip Clutch with Hex Socket Bolts” on page 16. Hex Head Bolts 24501 Slip Clutch with Hex Head Bolts Fig
ページ20に含まれる内容の要旨
Land Pride Table of Contents Section 4: Maintenance & Lubrication Refer to Figure 4-6 Clutch Assembly (with hex head bolts) 7. Progressively tighten each spring retainer bolt until Refer to Figure 4-5 correct compressed spring length “A” is reached. If clutch run-in indicated that one or more of the friction • A = 1.26” disks did not slip, then the clutch must be disassembled to separate parts. 1. Remove spring retainer nuts (#9a), springs (#2) and bolts (#9b) from the assembly. 2. Each friction
