ページ1に含まれる内容の要旨
Operator´smanual
iZ4217TSKAA/968999254,iZ4817TSKAA/968999255
iZ4821TSKAA/968999256,iZ5223TSKAA/968999257
iZ5223TKOA/968999258,iZ6123TKAA/968999259
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine. English
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
OPERATOR’S MANUAL RIDER iZ SERIES Maintenance ......................................................... 34 Contents Maintenance Schedule...................................... 34 Contents...................................................................1 Battery............................................................... 36 Introduction .............................................................3 Ignition System.................................................. 37 Congratulations..........
ページ4に含まれる内容の要旨
WARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower. Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance. WARNING! Engine exhaust, some of its constituents, and certain vehicle componets contain or emit chemicals
ページ5に含まれる内容の要旨
INTRODUCTION Introduction Congratulations Thank you for purchasing a Husqvarna ride-on mower. This machine is built for the greatest efficiency and rapid mowing primarily of large areas. Controls in one place and a hydrostatic transmission regulated by steering controls also contribute to the machine’s performance. This manual is a valuable document. Following the instructions (use, service, maintenance, etc.) can considerably increase the lifespan of your machine and even increase its resale va
ページ6に含まれる内容の要旨
INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer, see the certificate in the Service Journal in this operator’s manual. When you need spare parts or support in service questions, warranty issues, etc., please consult the follo
ページ7に含まれる内容の要旨
SYMBOLS AND DECALS Symbols and Decals These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. WARNING! Xxxxxxx xxxx xxxxxxxx xxx x Xxxxx xxxxxx xx. xx xxxxxxxx xxxxx xxx xx. Used in this publication to notify the reader of a risk of personal injury, particularly if the reader should neglect to follow instructions given in the manual. IMPORTANT INFORMATION Xxxxxxx xxxx xxxxxxxx xxx xxx xxxx xxxxxx xx. Used in this publication to n
ページ8に含まれる内容の要旨
SYMBOLS AND DECALS Shut off engine Keep a safe Read Use on No & remove key distance from slopes no passengers Operator´s before the machine. greater Manual. performing any than 10°. maintenance or repair work. Whole body Severing of Do not open Careful Careful going exposure to fingers & or remove backing up, forward, watch thrown toes. watch for other for other people. safety shields objects. people. while engine is running. Moving sharp blades under cover ROPS warning decal English-6
ページ9に含まれる内容の要旨
SAFETY INSTRUCTIONS Safety Instructions These instructions are for your safety. Read them carefully. WARNING! This symbol means that important safety instructions need to be emphasized. It concerns your safety. General Use Read all instructions in this operator’s manual and on the machine before starting it. Ensure that you understand them and then abide by them. Learn how to use the machine and its controls safely and learn how to stop quickly. Also learn to recognize the safety decals. O
ページ10に含まれる内容の要旨
SAFETY INSTRUCTIONS Be careful when mowing around fixed WARNING! objects, so that the blades do not hit them. Never drive over foreign objects. Engine exhaust and certain vehicle components contain Only use the machine in daylight or in or emit chemicals considered other well-lit conditions. Keep the to cause cancer, birth defects, machine a safe distance from holes or or other reproductive system other irregularities in the ground. Pay damage. The engine exhaust attention to other possible
ページ11に含まれる内容の要旨
SAFETY INSTRUCTIONS Driving on Slopes Driving on slopes is one of the operations where the risk is greatest that the driver will lose control or the machine will tip over, which can result in serious injury or death. All slopes require extra caution. If you cannot reverse up a slope or if you feel unsure, do not mow the slope. Do as follows Remove obstacles such as stones, tree branches, etc. Watch out for and avoid driving over furrows, holes, and bumps. On uneven terrain, the machine can t
ページ12に含まれる内容の要旨
SAFETY INSTRUCTIONS Children Serious accidents may occur if you fail to be on guard for children in the vicinity of the machine. Children are often attracted to the machine and mowing work. Never assume that children will stay put where you last saw them. Keepchildrenawayfromthe mowing area and under close supervision by another adult. Keep an eye out and shut off the machine if children enter the work area. 8011-517 Before and during a reversing maneuver, Never allow children to operate
ページ13に含まれる内容の要旨
SAFETY INSTRUCTIONS Maintenance WARNING! The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed. Stop the engine. Prevent the engine from starting by removing the spark plug cables from the spark plugs or by removing the ignition key before making any adjustments or performing maintenance. Never fill the fuel tank indoors. Fuel and fuel fumes are poisonous and extremely flammable. Be especially cautious when handling
ページ14に含まれる内容の要旨
SAFETY INSTRUCTIONS Acid in the eyes can cause blindness, contact a doctor immediately. Be careful when servicing the battery. Explosive gases form in the battery. Never perform maintenance on the battery when smoking or near open flames or sparks. The battery can explode and cause serious injury/ damage. Ensure that nuts and bolts, especially the fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition. 6003-009 Do not modify
ページ15に含まれる内容の要旨
SAFETY INSTRUCTIONS Stop and inspect the equipment if you run over or into anything. If necessary, Use protective glasses for make repairs before starting. maintenance work. Never make adjustments with the engine running. The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them. Check the parking brake’s functionality
ページ16に含まれる内容の要旨
SAFETY INSTRUCTIONS Roll over Protecion system ROPS The ROPS increases the basic weight of the unit by 34 lbs/16kg. ROPS for the US is standard equipment, accessory for Europe. WARNING! The structures capability may be imparired by structural damage if overturned, or alteration occurs. If any of these conditions take place, the total structure MUST be replaced. Do not use ROPS as a lifting, attaching or anchoring point. Do not use ROPS for wrecking or towing. Do not exceed Max GVW: 2614 lb
ページ17に含まれる内容の要旨
CONTROLS Controls This operator’s manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a Kawasaki or Kohler four-stroke V-Twin engine developing 17-23 horse power. Transmission from the engine is made via two belt-driven hydraulic pumps, which in turn drive a hydraulic motor for each drive wheel. Using the left and right steering controls, the flow is regulated and thereby the direction and speed. 8011-583 Zero Turn Rider 8011-767 Locations of the controls Control Loc
ページ18に含まれる内容の要旨
CONTROLS 1. Motion Control Levers The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward. When both controls are in the neutral position (N), the machine stands still. By moving both controls an equal amount forward or backward, the machine moves in a 8011-788 straight
ページ19に含まれる内容の要旨
CONTROLS 2. Hour Meter The hour meter displays the total operating time. It will flash CHG OIL (Change Oil) at 50 hour intervals. The flash duration is one hour before and one hour after the interval. The CHG OIL icon will come on and shut off automatically. The hour meter can not be manually reset. hourmeter Hour meter 3. Tracking Knob The tracking knob is located in front of the left control lever. Rotating this knob allows fine tuning adjustments so that the machine tracks straight w
ページ20に含まれる内容の要旨
CONTROLS 5. Blade switch In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed. 8011-510 Blade Switch 6. Ignition Switch The ignition key is placed in the ignition switch on the driver’s panel and is used to start and stop the engine. IMPORTANT INFORMATION Do not run the starter for more than five seconds each time. If the engine does not start, wait about 10 seconds before re- trying. 8011-521 Ignition key and hour meter 7. Fuses
