ページ1に含まれる内容の要旨
Models:
Operators manual
968999204 / iZ4218KAA
968999205 / iZ4818KAA
968999206 / iZ4821KAA
968999207 / iZ5223KAA
Please read these instructions carefully and make
968999208 / iZ5223KOA
sure you understand them before using the machine.
MANUAL NO. 539107291 REV. IR (05/29/02)
ページ2に含まれる内容の要旨
Congratulations on the purchase of your HUSQVARNA mower. This manual has been prepared for the owners and operators of the models called out on the front cover of this manual. Read, understand and follow the safety and operating instructions. ! WARNING Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower
ページ3に含まれる内容の要旨
CONTENTS SAFETY INSTRUCTIONS ..................... 4 Pump belt ................................... 15 General use and saftey rules..... 4,5 Lubrication .................................. 15 Tire pressure .............................. 15 Driving on slopes ....................... 5 Children safety ........................... 5 Caster wheels ............................ 15 Service safety ............................ 5,6 Fuel filter ..................................... 15 Transportation ..........
ページ4に含まれる内容の要旨
SAFETY INSTRUCTIONS IMPORTANT ! This cutting machine is capable of amputat- ing hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. FIG - 1 General use and safety rules: Read , understand and follow all instructions in the manual and on the machine before start- ing. FIG - 1 Make yourself familiar with the controls and how to stop quickly. Only allow adults who are familiar with the instructions and the machine to ope
ページ5に含まれる内容の要旨
SAFETY INSTRUCTIONS Use extra care when using a grass catcher on Never operate the mower without the entire slopes. grass catcher or discharge chute in place. Avoid stopping and starting on slopes. Slow down before turning. Do not cut wet grass. The tires will loose grip Never leave the machine unattended when the and the machine can slide. engine is running. Always turn off the blades, set the parking brake, stop the engine and take Children safety out the keys before leaving the machine. Stop
ページ6に含まれる内容の要旨
SAFETY INSTRUCTIONS Never operate the machine without proper guards, covers, safety switches and devices in place and properly functioning. Inspect these items regularly. If their condition or operation is ! DANGER questionable they must be replaced before THE MOWER SHALL NOT BE OPERATED WITHOUT using the machine. FIG - 2 EITHER THE ENTIRE GRASS CATCHER OR THE CHUTE DEFLECTOR COVERING THE GRASS DISCHARGE OPENING. DO NOT REMOVE THE GRASS CATCHER OR Keep machine free of grass, leaves and other CHU
ページ7に含まれる内容の要旨
PRESENTATION Presentation Thank you for buying a HUSQVARNA! Before Lawnmowers and all power equipment, can be potentially dangerous if used improperly. operating your new mower, read, understand Safety requires good judgement, careful use in and follow the safety instructions and other accordance with these instructions and com- directions in this manual. mon sense. Motion Control Levers Deck Lift Lever Fuel Cap Park Brake Lever Blade Engagement Switch Key Switch 7
ページ8に含まれる内容の要旨
SETUP AND ADJUSTMENTS WARNING: No settings or adjustments are to be made unless: Engine is stopped, key has been removed, park brake is on and battery cable removed from battery. Setup Uncrate machine. Control Motion Mount rear drive wheels using the lug nuts Arm Control installed on the hubs. Lever Check the tire pressure in all four tires. All tires should be 15 psi. FIG - 3 Remove top bolt in control arm and loosen bottom bolt, rotate the control levers to the upright position. Align the leve
ページ9に含まれる内容の要旨
SETUP AND ADJUSTMENTS Rotate the motion control lever out into the Mower Deck Leveling neutral slot. While the lever is swung out into Position machine on a flat surface. Preferably the neutral slot pull it against the the back edge level concrete. of the neutral slot. Holding the lever adjust the spring by sliding the bolt in the slot to remove Check the tire pressure in all four tires. Inflation all the slop and retighten the bolt. should be 15 psi. Check your adjustment by repeating the sec-
ページ10に含まれる内容の要旨
SETUP AND ADJUSTMENTS Park Brake Adjustment 1. Stop engine and remove key. Release park brake and measure the length of the spring. The distance between the washer on each end of the spring should be 2-7/8". FIG - 7 2. If adjustment is needed, loosen the nut below the spring. Then rotate nut to desired position so the proper distance between the washers is obtained. Check other side for proper adjust- ment. FIG - 7 3. Engage the brake lever and measure the distance between the trunnion pin and t
ページ11に含まれる内容の要旨
OPERATING INSTRUCTIONS Run engine full throttle to make sure wheels do not rotate. Readjust if any rotation occurs. Repeat the whole process for the opposite side and tighten the nuts against the ball joints. Turn machine off. Reinstall the seat rod and check the wiring harness to the seat safety switch for a good connection and return the seat to the normal position. Operating instructions Starting and operation Operator must be sitting in the seat. Engage the park brake, blades disengaged and
ページ12に含まれる内容の要旨
OPERATING INSTRUCTIONS By moving the levers an equal amount forward Key switch is located on the console. Used to or back the machine will move in a straight line start the machine. NOTE: Do not run the starter in that direction. FIG - 10 for more than 5 seconds at a time. If the engine will not start, wait about 10 seconds before Movement of either lever forward will cause the trying again. FIG - 11 right or left wheel to rotate in a forward direction. To stop movement pull both levers into the
ページ13に含まれる内容の要旨
MAINTENANCE Fuel shut off valve is located at the right rear of the seat. The valve has three positions a right Fuel Valve tank, left tank and center is the off position. FIG - 12. NOTE: EFI models the left position is the off position. Pump release valves located at the right front corner of the pumps. Used to release the system so the machine may be moved by hand when not running. Tilt seat forward to gain access to the pumps. Use a 5/8 wrench to FIG - 12 open valve. NOTE: Only rotate valve
ページ14に含まれる内容の要旨
MAINTENANCE Hardware Check daily. Inspect the entire machine for loose or missing hardware. Air filter See engine manufacturers specifications for cleaning and replacement intervals. Hydraulic system Check oil level in tank daily. Oil level should be 3/4 to 1 below the top of the tank. Check all fittings, hoses and lines for damage or leaks. Replace or repair any questionable lines or fittings. ONLY USE Change the oil and filter after the first 250 hours of operation then annually after that.
ページ15に含まれる内容の要旨
MAINTENANCE FIG - 16 Caster Wheels Pump belt Check every 200 hours. Lift front of unit off of Check belt every 100 hours for excessive wear. ground so caster wheels can rotate freely. To replace belt. Relieve tension on the deck belt Tighten caster bolt then back off 1/2 turn. Check and remove deck belt from clutch. See deck belt that wheel rotates freely. If wheel does not rotate instructions on previous page. Loosen bolt on freely back the caster bolt off in 1/4 turn incre- the clutch tie down
ページ16に含まれる内容の要旨
MAINTENANCE Torque Specifications · Engine crankshaft bolt 67 Nm(50 ft/lb) · Deck pulley bolts 61 Nm (45 ft/lb) · Hydraulic tube nuts 41 Nm (30 ft/lb) · Wheel motor hub nut 122 Nm (90 ft/lb) · Lug nuts 100 Nm (75 ft/lb) · Blade bolt 122 Nm (90 ft/lb) · Standard ¼ fasteners 12 Nm (9 ft/lb) · Standard 5/16 fasteners 25 Nm (18 ft/lb) · Standard 3/8 fasteners 44 Nm (33 ft/lb) · Standard 7/16 fasteners 70 Nm (52 ft/lb) · Standard ½ fasteners 110 Nm (80 ft/lb) 16
ページ17に含まれる内容の要旨
MAINTENANCE Maintenance Schedule For ZTH Riders Maintenance Maintance Interval (hours) Daily 25 50 100 200 250 500 Engine (4) Check oil level X Change oil and filter (1) X Clean the air filters (3) X Replace air filters (3) X Check for fuel and oil leakage X Clean cooling flanges (3) X Check cooling air inlet X Check fuel pumps air filter X Replace fuel filter X Replace plugs X Hydraulics Check oil level X Check for oil leaks X Change hydraulic oil (2) XX Change oil filter (2) XX Electrical C
ページ18に含まれる内容の要旨
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSES Blade switch on. Drive levers not in the neutral slots. Operator not in seat. ENGINE WILL NOT START. Park brake disengaged. Dead battery. Fuel valve closed or in the wrong position. No fuel. Spark plugs defective. Spark plug wires off. Park brake on. Pump bypass valves open. MACHINE WILL NOT MOVE OR MOVES Pump drive belt loose or off. SLOWLY OR HARD. Hydraulic system failure. Air in the hydraulic system. Blade belt off. Clutch unhooked form wiring harness
ページ19に含まれる内容の要旨
Starter Switch Hour Meter Left Motion Seat Control Blade Switch Right Motion Control Frame Harness P/N 104414 Engine Clutch WIRING DIAGRAMS CONSOLE HARNESS 19
ページ20に含まれる内容の要旨
WIRING DIAGRAMS CONSOLE HARNESS SCHEMATIC 20
