ページ1に含まれる内容の要旨
®
HUSQVARNA AUTOMOWER
305
OPERATOR’S MANUAL
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
TABLE OF CONTENTS 1. Introduction and safety .............................................................. 5 1.1 Introduction ..................................................................................... 5 1.2 Symbols on the product .............................................................. 6 1.3 Symbols in the Operat
ページ4に含まれる内容の要旨
MEMO Serial number: PIN code: Dealer: Dealer’s telephone number: If the mower is unexpectedly stolen, it is important to notify your dealer of this. Provide the serial number of the mower so that is can be registered as stolen in the central systems at Husqvarna AB. It is an important step in theft protection procedure which reduces interest in the buying and selling of stolen mowers. www.automower.com 4 - English
ページ5に含まれる内容の要旨
1. INTRODUCTION AND SAFETY 1. Introduction and safety 1.1 Introduction Congratulations on your choice of an exceptionally high quality product. To get the best results from your ® Husqvarna Automower requires knowledge of its function. This Operator's Manual contains important information about the mower, how it must be installed and how to use it. As a complement to this Operator's Manual, there is ® more information available on the Automower www.automower.com w
ページ6に含まれる内容の要旨
1. INTRODUCTION AND SAFETY 1.2 Symbols on the product These symbols can be found on the robotic lawn mower. Study them carefully. • Read through the Operator’s Manual carefully and understand the content before using your ® Automower . The warnings and safety instructions in this Operator’s Manual must be carefully followed if the mower is to be used safely and efficiently. ® • Automower can only start when the main switch is moved to the 1 position and the correct P
ページ7に含まれる内容の要旨
1. INTRODUCTION AND SAFETY 1.3 Symbols in the Operator’s Manual These symbols can be found in the Operator’s Manual. Study them carefully. • Turn the main switch to 0 before carrying out any inspections and/or maintenance. • Always wear protective gloves when working with the mower’s underframe. • Never use a high-pressure washer or even ® running water to clean Automower . • A warning box indicates a risk of personal injury exist, especially when the stated instructions are WARN
ページ8に含まれる内容の要旨
1. INTRODUCTION AND SAFETY 1.4 Safety instructions Use • This robotic lawn mower is designed to mow grass in open and level ground areas. It may only be used with the equipment recommended by the manufacturer. All other types of use are incorrect. The manufacturer’s instructions with regard to operation, maintenance and repair must be followed precisely. • The robotic lawn mower may only be operated, maintained, and repaired by persons that are fully
ページ9に含まれる内容の要旨
1. INTRODUCTION AND SAFETY • Husqvarna AB does not guarantee full ® compatibility between Automower and other types of wireless systems such as remote controls, radio transmitters, buried electric animal fencing or similar. Transport The original packaging should be used when ® transporting Automower over long distances. To safely move from or within the working area: 1. Press the STOP button to stop the mower. If security is set to the medium or high level (
ページ10に含まれる内容の要旨
2. PRESENTATION 2. Presentation This chapter contains information that is important to be aware of when planning the installation. ® An installation of Husqvarna Automower includes four main components: ® • The Automower is a robotic lawn mower that mows the lawn by essentially operating in a random pattern. The mower is powered by a maintenance-free battery. ® • Charging station, where your Automower returns when the charge level in the battery becomes too low. The charg
ページ11に含まれる内容の要旨
2. PRESENTATION 2.1 What’s what? 5 3 4 2 1 6 7 15 14 11 8 13 12 9 17 10 16 20 18 19 21 22 23 24 The numbers in the picture correspond to: 1. Body 14. Keypad 2. Cover to display, keypad and cutting height 15. Display adjustment 16. Loop wire for boundary wire and guide wire 3. Stop button/Lock button for opening the cover 17. Low voltage cable 4. Contact strip 18. Connector for the loop wire 5. LED for operation check of the charging station, 19. Nails for securing the charging station bo
ページ12に含まれる内容の要旨
2. PRESENTATION 2.2 Function Capacity ® 2 Automower is recommended for lawns up to 500 m in size. ® How big an area Automower can keep cut depends primarily on the condition of the blades and the type, growth and moisture of the grass. The shape of the garden is also significant. If the garden mainly consists ® of open lawns, Automower can mow more per hour than if the garden consists of several small lawns separated by trees, flower beds and passages. ® A ful
ページ13に含まれる内容の要旨
2. PRESENTATION Working method ® The Automower automatically mows the lawn. It continuously combines mowing and charging. The mower starts to search for the charging station when the battery charge becomes too low. ® Automower does not mow when it is searching for the charging station. ® When Automower searches for the charging station, it first searches irregularly for the guide wire. Then it follows the guide wire to the charging station, turns around just i
ページ14に含まれる内容の要旨
2. PRESENTATION ® The control panel on the top of Automower is where you manage all the mower settings. Open the control panel cover by pressing down the STOP button. When the main switch is set to position 1 for the first time, a start-up sequence begins which includes: language selection, time format, date format and the four-digit PIN code and setting the time and date, see 3.8 First start-up and calibration on page 32. After this, the selected PIN code must be entered
ページ15に含まれる内容の要旨
3. INSTALLATION 3. Installation This chapter describes how you install the Husqvarna ® Automower . Before starting the installation read the previous chapter 2. Presentation. Read also through this entire chapter before beginning the installation. How the installation is made also ® affects how well Automower will work. It is therefore important to plan the installation carefully. Planning is simplified if you make a sketch of the working area, including all obstacles. This makes it easie
ページ16に含まれる内容の要旨
3. INSTALLATION • Transformer (20) • Low voltage cable (17) • Staples (21) • Connector for the loop wire (18) • Screws for the charging station (19) • Measurement gauge (22) • Solderless coupler for the loop wire (23) During installation you will also need: • Hammer/plastic mallet to simplify putting the staples in the ground • Combination pliers for cutting the boundary wire and pressing the contact units together. • Edge cutter/straight spade if the boundary wire must be buried.Installatio
ページ17に含まれる内容の要旨
3. INSTALLATION The charging station must be positioned with a great deal of free area in front of it (at least 3 metres). It should also be centrally placed in the working area so ® that Automower finds it easier to reach all areas in the working area. Do not put the charging station in confined spaces in the working area. There must be a straight boundary wire, at least 1.5 metres long, to the right and left of the charging station. The wire must be laid straight out from the rear end o
ページ18に含まれる内容の要旨
3. INSTALLATION If the installation is done in a working area with a steep slope (such as around a house on a hill), the charging station should be placed in the area at the bottom of the slope. This makes it easier for the lawn mower to follow the guide wire to the charging station. The charging station should not be placed on an island as this limits the laying of the guide wire in an optimal way. If the charging station has to be installed on an island, the guide wire also has to be c
ページ19に含まれる内容の要旨
3. INSTALLATION The transformer shall be mounted on a vertical surface, for example a house wall. Mount the transformer with screws in the two attachment points. Securing screws are not included. Choose screws suitable for the wall material. Mount the transformer at a height such that there is no risk the transformer can become submerged in water (minimum 30 cm from the ground). The min 30cm/12” transformer must never be placed on the ground. IMPORTANT INFORMATION The low volta
ページ20に含まれる内容の要旨
3. INSTALLATION IMPORTANT INFORMATION The transformer may not be exposed to direct sunlight. 3.3 Charging the battery As soon as the charging station is connected, it is possible to charge the mower. Set the main switch to the 1 position. ® Place Automower in the charging station to charge the battery while the boundary and guide wires are being laid. If the battery is flat, it takes around 80 to 100 minutes to fully charge it. IMPORTANT INFORMATION ® Automower cannot be used before the in
