ページ1に含まれる内容の要旨
For all customer enquiries or for replacement parts, contact:-
0870 609 1901
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
ページ2に含まれる内容の要旨
Carton Contents switchbox start/stop levers upper handle cable clip lower handle handle washer grassbox lid knobs bolt Easi-Reel cable winder retaining clip washer pin nuts bolt retaining clip electric cable with moulded plug cutting height grassbox spacers (1 fitted to pin lawnmower & 2 in loose parts pack spanner/scraper tool instruction manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna
ページ3に含まれる内容の要旨
3. Do not use the lawnmower if the electric cables are 5. Mow across the face of slopes, never up and down. damaged or worn 6. Exercise extreme caution when changing direction 4. Immediately disconnect from the mains electricity sup- on slopes. Walk never run. ply if the cable is cut, or the insulation is damaged. Do 7. Mowing on banks and slopes can be dangerous. not touch the electric cable until the electrical supply Do not mow on banks or steep slopes. has been disconnected. Do not repair
ページ4に含まれる内容の要旨
Assembly Instructions B Lower handle assembly (A) 1. Insert the lower handle into the handle slots, ensuring that the holes are aligned. 2. Insert the pins and secure with the retaining clips. 1 Upper handle assembly (B) 2 1. Insert the nut into the handle knob. (B1) 2. Align the holes in the upper and lower handles and secure with the bolt, washer and wing knob.(B2) 3. Fit the cable to the handle with the clip provided. (B3) Make sure the cable is not trapped between the upper and lower handl
ページ5に含まれる内容の要旨
Starting and Stopping To Start your Lawnmower D E The Flymo Vision Compact uses an advanced belt drive system, between the motor and the blade which improves cutting power and flotation in all conditions. Due to the high turning force (Torque) which this motor develops a light squeak may be heard when the machine is started, this is quite normal and will not affect the performance of the product 1. Connect female extension cable connector to the back of the switchbox. (D) 2. Form loop in mains c
ページ6に含まれる内容の要旨
Adjusting the Cutting Height Always handle the blade with care - sharp edges K could cause injury. USE GLOVES. Never use more than 3 Cutting Height Spacers. Spacers must only be fitted between the blade and the fan and NEVER between the blade and the bolt. 1. Remove the blade bolt, and blade as described in Removing the Blade and Fan. 2. For a Lower Cut - Add spacers to a maximum of 3. 3. For a Higher Cut - Take spacers away. 4. Refit the blade as described in Fitting the Blade and Fan. Removing
ページ7に含まれる内容の要旨
Easi-Reel Cable Winder R1 R2 Storing your cable in the Easi-Reel cable winder 1. Insert the female connector into the top of the cable winder (R1) 2. Place the cable under the cable guide (R2) 3. Turn the cable winder (R3) until all of the cable is wound in.(R4) Warning:- When cable is fully wound, lid R3 R4 becomes heavy Unwinding the cable before re-use 1. Pull the cable by the plug and unwind the cable fully. • Ensure that the cable is released from the cable guide (R2) before using your mac
ページ8に含まれる内容の要旨
Caring for your Lawnmower Cleaning S IMPORTANT: It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the hood could become a potential fire hazard. USE GLOVES It is recommended that you clean your lawnmower straight after mowing while the grass is still wet. 1. Remove grass from under the hood with the spanner/scraper tool. (S) 2. Remove the blade, see Figure L, to gain access to the fan and clean with a soft brush. (S) 3. Lever the
ページ9に含まれる内容の要旨
Fault Finding Hints Fails to Operate Poor Collection 1. Is the correct Starting procedure being followed? 1. Is the grassbox lid firmly closed? See ‘To Start your Lawnmower’ 2. Is the grassbox fitted correctly? 2. Is the Power Turned On? 3. Are you mowing correctly? 3. Check the fuse in the plug, if blown replace. 4. Check all air vents and openings are not obstructed. 4. Fuse continues to blow? 5. Raise to a higher height of cut. See ‘Adjusting the Immediately disconnect from the mains electr
ページ10に含まれる内容の要旨
EC Declaration of Conformity I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, Husqvarna Outdoor Products, Aycliffe NEWTON AYCLIFFE, Co. Durham. DL5 NEWTON AYCLIFFE, Co. Durham. DL5 Industrial Park, NEWTON AYCLIFFE, Co. 6UP. Certify that the product:- 6UP Certify that a sample of the above Durham. DL5 6UP Certify that a sample product has
