ページ1に含まれる内容の要旨
COMMERCIAL 21
For Serial Nos.
312,000,000 & Higher
Par t No. 4500-927 Rev . A
ページ2に含まれる内容の要旨
W ARNING CALIFORNIA Pr oposition 65 W ar ning T he engine exhaust fr om this pr oduct contains chemicals kno wn to the State of Calif or nia to cause cancer , bir th defects, or other r epr oducti v e har m. Important: T he engine in this pr oduct is not equipped with a spar k ar r ester muf fler . It is a violation of Calif or nia Public R esource Code (CPR C) Section 4442 to use or operate this engine on an y f or est-co v er ed, br ush-co v er ed, or g rass-co v er ed land as defined in CPR C
ページ3に含まれる内容の要旨
Introduction CONGRATULATIONS on the purc hase of y our Exmark Mo w er . T his product has been carefully designed and man ufactured to gi v e y ou a maxim um amount of de pendability and years of trouble-free operation. T his man ual contains operating, maintenance , adjustment, and safety instr uctions for y our Exmark mo w er . BEFORE OPERATING Y OUR MO WER, Figure 1 CAREFULL Y READ THIS MANU AL IN ITS 1. Model and serial number location ENTIRETY . By follo wing the operating, maintenance , an
ページ4に含まれる内容の要旨
Cleaning Under the Co v er Plate (Non-Blade Contents Brak e Clutc h Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 W aste Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Storag e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ5に含まれる内容の要旨
Safety Safe Operating Practices Safety T raining Safety Alert Symbol • R ead the Operator’ s Man ual and other training T his la wn mo w er meets or ex ceeds the Consumer material. If the operator(s) or mec hanic(s) can Product Safety Commission (CPSC) blade safety not read English it is the o wner’ s responsibility to requirements for w alk-behind rotar y mo w ers and explain this material to them. the B71.4 specifications of the American National • Become familiar with the safe operation of th
ページ6に含まれる内容の要旨
Safety • Inspect the area where the equipment is to be DANGER used and remo v e all roc ks , to ys , stic ks , wires , In cer tain conditions during fueling , static bones , and other foreign objects whic h can be electricity can be r eleased causing a spar k thro wn b y the mac hine and ma y cause personal which can ignite gasoline v apor s. A fir e or injur y to the operator or b ystanders . explosion fr om gasoline can bur n y ou and other s and cause pr oper ty dama ge. DANGER • Al w ays pla
ページ7に含まれる内容の要旨
Safety Operation • P ark the mac hine on lev el g round. Stop engine , w ait for all mo ving par ts to stop , and remo v e the spark plug wire(s). W ARNING Operating engine par ts, especiall y the muf fler , – Before c hec king, cleaning or w orking on the become extr emel y hot. Sev er e bur ns can occur mo w er . on contact and de bris, such as lea v es, g rass, – After striking a foreign object or abnor mal br ush, etc . can catch fir e. vibration occurs (inspect the mo w er for • Allo w engi
ページ8に含まれる内容の要旨
Safety • Use extreme care when loading or unloading the • K ee p engine and engine area free from mac hine into a trailer or tr uc k. accum ulation of g rass , lea v es , ex cessi v e g rease or oil, and other debris whic h can accum ulate • Use care when approac hing blind cor ners , shr ubs , in these areas . T hese materials can become trees , or other objects that ma y obscure vision. combustible and ma y result in a fire . • Let engine cool before storing and Do Not store Slope Operation ne
ページ9に含まれる内容の要旨
Safety Safety and Instructional Decals • K ee p all safety signs legible . R emo v e all g rease , • New safety signs ma y be obtained from dir t and debris from safety signs and instr uctional y our authorized Exmark equipment dealer or labels . distributor or from Exmark Mfg . Co . Inc . • R e place all w or n, damag ed, or missing safety • Safety signs ma y be affix ed b y peeling off the signs . bac king to expose the adhesi v e surface . Apply only to a clean, dr y surface . Smooth to remo
ページ10に含まれる内容の要旨
Safety 109-9317 1 16-1922 1 17–2718 1 16-2737 10
ページ11に含まれる内容の要旨
Specifications Specifications Model Numbers Serial Nos: 312,000,000 and Higher ECSKAP21; ECSKA21; ECXKA21; ECXHN21; ECXKABBC21; ECXHNBBC21 Systems Safety Interlock System F or units without a Blade Brak e Clutc h: Operator Engine m ust ha v e the blade control bail de pressed to star t the engine . R eleasing the blade control bail will cause • Engine Specifications: See y our Engine Owner’ s the engine to stop . Man ual • Engine Oil T ype: Exmark 4–Cycle Premium T ransmission (Self Propelled Un
ページ12に含まれる内容の要旨
Product Overview Overall Length and Height at Product Overview 2 1/2 inch Cutting Height: Handle Setting Length Height High 61.00 inc hes 39.00 inc hes (99.1 (154.9 cm) cm) Medium 63.00 inc hes 37.50 inc hes (95.3 (160.0 cm) cm) Lo w 64.50 inc hes 35.00 inc hes (88.9 (163.8 cm) cm) Figure 3 1. Grass bag 5. Discharge door 2. Handle 6. Rear wheel height adjustment 3. Drive Bail 7. Front wheel height (Self-Propelled Units adjuster Only) 4. Blade Control Bail 12
ページ13に含まれる内容の要旨
Operation is de pressed to w ard the handle . W hen this bail is Operation released the unit will stop mo ving . Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. Throttle-Choke Lever (ECXHN21) Located on the left side of the handle bar . Controls T he lev er is used to control engine speed. Mo ving the throttle to the full forw ard (Chok e) position will Blade Control Bail place the lev er in the c hok e position. T he c hok e aids in star ting a col
ページ14に含まれる内容の要旨
Operation Figure 7 1. Rotate clockwise to close 2. Rotate counterclockwise to open On ECXHN21 and ECXHNBBC21 units , the fuel shut off v alv e is located on the engine as sho wn in Figure 8 . R otate 1/4 tur n cloc kwise to shut off fuel. Figure 5 R otate the v alv e 1/4 tur n countercloc kwise to tur n Clear plastic cover removed for clarity on fuel. 1. Engine stop switch 2. Press “ST OP” to kill engine 3. Press “I” before starting engine Fuel Shut-Off V alve T he fuel shut off v alv e is locat
ページ15に含まれる内容の要旨
Operation Operating Instructions Handle Adjustment T he height of the handle can be adjusted for comfor table operation. Stand behind the handle to deter mine the height. T o adjust the handle height, position the hardw are into one of the three holes in the handle brac k et. Open the Fuel Shut-Off V alve R otate the v alv e 1/4 tur n countercloc kwise to tur n Figure 10 the fuel on (if equipped). Kawasaki units with large fuel tank shown 1. Muf fler Starting the Engine 2. Oil fill/dipstick 1. C
ページ16に含まれる内容の要旨
Operation 5. F or units without a Blade Brak e Clutch: Hold self-propels at the maxim um g round speed. the blade control bail to the handle . R elease the dri v e bail to stop mo ving when y ou use the la wn mo w er for trimming or whenev er 6. Pull the star ter handle lightly until y ou feel y ou lea v e the la wn mo w er . resistance , then pull it shar ply . Allo w the rope to retur n slo wly . 3. T o diseng ag e the self-propel dri v e , release the dri v e bail. 7. F or ECXHNBBC21 Units: G
ページ17に含まれる内容の要旨
Operation Using the Mulch Plug 1. Stop the engine and w ait for all mo ving par ts to stop . Occasionally y ou ma y wish to use the m ulc h plug to 2. Mo v e the la wn mo w er onto a pa v ed surface in m ulc h the g rass and leaf clippings bac k into the la wn. a non-windy area. • Installing the Mulc h Plug: 3. Set all four wheels to the 2 1/2 inc hes (6.4 cm) 1. Stop the engine and w ait for all mo ving par ts cutting height (see Figure 15 and Figure 16 ) to stop . 4. T ak e a half sheet of new
ページ18に含まれる内容の要旨
Operation the blade has not properly stopped, resulting W ARNING in an unsafe operating condition. Contact an Adjusting the cutting height lev er s could bring Authoriz ed Ser vice Dealer . y our hands into contact with a mo ving blade. A mo ving blade can cause serious injur y . DANGER • Stop the engine and w ait f or all mo v ement to If the blade brak e clutch system is inoperati v e, stop bef or e adjusting the cutting height. the blade will contin ue to r otate when y ou r elease the blade
ページ19に含まれる内容の要旨
Operation Figure 16 1. Front wheel shaft 4. Front quadrant block cut assembly heights 2. Pull up 5. Pull outward 3. Height adjuster 6. Shaft groove 2. Inser t the front wheel shaft assembly into the Figure 17 desired cut height setting in the front quadrant 1. Bag 4. Handle bracket notch bloc k. Lo w er the height adjuster into the 2. Handle 5. Rear door g roo v e on the front wheel shaft. Pull and 3. Bag frame 6. Lower push the wheel shaft assembly to mak e sure it has loc k ed into place . 4.
ページ20に含まれる内容の要旨
Operation • Alter nate the mo wing direction. T his helps DANGER disperse the clippings o v er the la wn for ev en If the discharge door does not close fer tilization. completel y , the la wn mo w er could thr o w • If the finished la wn appearance is unsatisfactor y , objects. T hr o wn objects can r esult in tr y one or more of the follo wing: serious per sonal injur y or death to the operator or bystander s. – Shar pen the blade . • Nev er open the door to the discharge – W alk at a slo w er
