ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Safety Instructions Notes: CERTIFICATE OF CONFORMITY Contents Summary: Safety Instructions -Page 2 and 3 EC Declaration of Conformity Controls and Indicators - Dashboard -Page 4 I, the undersigned A. Bennett of Countax Limited Great Haseley Oxford Controls -Page 5 and 6 OX44 7PF declare that the Lawnmowers described below : Mulch Deck -Page 7 Rear Discharge Deck -Page 8 Model A20/ 50 Power (kW) 14.9 Cutter Deck Removal -Page 9 Maximum blade rotation (rpm) 3100 Cutter Deck - Check List -Page 10
ページ3に含まれる内容の要旨
Notes: Safety Instructions 4. Replace faulty silencers. damage and make repairs before restarting the Tractor). 5. Before using always inspect to see that the blades, bolts and • If the machine starts to vibrate abnormally check immediately cutter assembly are not worn or damaged. and call dealer if necessary. 6. Check the condition of the tyres and ensure that they are 13.Disengage drive to attachments when transporting or not in use. inflated to the correct pressure (refer to the specificatio
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
Controls - Levers Wiring Diagram POWER-TAKEOFF (PTO) fig 1 Push the lever down and to the left to engage the pto, to disengage TRA TRACT CTOR OR WIRING DIA WIRING DIAGRAM GRAM push the lever down and lift to the right. IMPORTANT - READ SAFETY INSTRUCTIONS BEFORE OPERATING THIS MACHINE MULCHING For Best results; - Do not reduce the height of the grass by more than 1/3 in a single pass O 15 MAX 15 MAX 1 White White - Mow often - short clippings of 25mm (1") or less decompose more quickly - If p
ページ7に含まれる内容の要旨
Electrical Mulch Deck There are five 20 Amp fuses on the MULCH MOWING Mulch Deck fig 1 A20/50 Tractor. Blades Mulching can save time, avoids gathering 1. 20Amp (yellow) for charging circuit. piles of rotting cuttings and feeds your Fuse Box 2. 20Amp (yellow), ignition, safety lawn. It is however necessary to observe switches. 1 certain rules to mulch mow successfully: 3. 20Amp (yellow) electric lift for Cutter 2 Deck and Auxiliary lift. 3 • Reduce the height of the grass by no 4.20Amp (yel
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
Cutter Deck Removal Engine - Oil (Mulch/Rear Discharge Deck) The Rear Discharge Deck is used in conjunction with the OIL DRAINING Before carrying out any fig 1 fig 1 PGC. It ejects the grass rearwards after cutting for the repair or servicing NOTE: OIL SHOULD BE CHANGED Powered Grass Collector to collect. Either the Mulch Deck or C D WITHOUT FAILAFTER THE FIRST the Rear Discharge Deck can be fitted to the A20/50 using the FIVE HOURS OF RUNNING. following instructions: Ensure that the Tractor is
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
Tyres - Check List Deck Levels - Front to Back The Cutter Deck should be set so that it is parallel to the fig 1 surface it is cutting with a maximum variation from side to side, or front to back of 3mm. Check this by placing the Tractor on a hard level surface and measuring the clearance Countax Tractors are fitted with grassland tyres that are designed to present a heights front to back and side to side with a steel ruler or tape with the Cutter set one adjustment up from its lowest position.
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
Collector - Drive Belts Cutter - Drive Belt Rod are threaded. You increase Belt REPLACING AND CHECKING, TENSIONING ENGINE TO CUTTER DRIVE Specified Belts and Blades fig 1 tension by winding the Trunnion Engine/Deck Belt - B57 Dayco Super II - TENSIONING PTO DRIVE AND REPLACING SIDE BELT TENSION towards the end of the Rod and reduce Pt No. 22940100 BELT CONNECTION DRIVE BELT (fig 3) tension by winding in the reverse The correct tension of the Cutter Drive direction. Deck Internal Drive (Mulch
ページ14に含まれる内容の要旨
