ページ1に含まれる内容の要旨
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Otreap Or ’s Mlauna
Push Mower — Model Series 180
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA Form No. 769-03809
(January 15, 2008)
ページ2に含まれる内容の要旨
To The Owner 1 Thank You Thank you for purchasing a Lawn Mower manufactured by Cub This product has met the rigid safety standards of the Outdoor Cadet LLC. It was carefully engineered to provide excellent Power Equipment Institute and an independent testing performance when properly operated and maintained. laboratory. If you have any problems or questions concerning the machine, phone your local Cub Cadet dealer or contact us Please read this entire manual prior to operating the equipment
ページ3に含まれる内容の要旨
Important Safe Operation Practices 2 WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! CALIFORNIA PROPOSITION 65 WARNING: Engine Exhaust, some of its constituents, and certain v
ページ4に含まれる内容の要旨
12. A missing or damaged discharge cover can cause blade 27. When starting engine, pull cord slowly until resistance contact or thrown object injuries. is felt, then pull rapidly. Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than 13. Many injuries occur as a result of the mower being pulled you can let go. Broken bones, fractures, bruises or sprains over the foot during a fall caused by slipping or tripping. could result. Do not hold on to the mow
ページ5に含まれる内容の要旨
3. Check the blade and engine mounting bolts at frequent Service intervals for proper tightness. Also, visually inspect blade for damage (e.g., bent, cracked, worn) Replace blade with Safe Handling Of Gasoline: the original equipment manufacture’s (O.E.M.) blade only, 1. To avoid personal injury or property damage use extreme listed in this manual. “Use of parts which do not meet the care in handling gasoline. Gasoline is extremely flammable original equipment specifications may lead to i
ページ6に含まれる内容の要旨
Spark Arrestor Average Useful Life According to the Consumer Products Safety Commission WARNING: This machine is equipped with an (CPSC) and the U.S. Environmental Protection Agency (EPA), internal combustion engine and should not be used this product has an Average Useful Life of seven (7) years, or 140 on or near any unimproved forest-covered, brush hours of operation. At the end of the Average Useful Life, buy covered or grass-covered land unless the engine’s a new machine or have the
ページ7に含まれる内容の要旨
Fold along dotted line (represents a 15° slope) Sight and hold this level with a vertical tree... or a corner of a building... or a fence post 15° Use this page as a guide to determine slopes where you may not operate safely. WARNING: Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. Operate riding mowers up and down slopes, neve
ページ8に含まれる内容の要旨
Assembly & Set-Up 3 Contents of Carton • One Lawn Mower • One Grass Catcher • One Bottle of Oil • One Lawn Mower Operator’s Manual • One Engine Manual • One Side Discharge Chute Assembly NOTE: This unit is shipped without gasoline or oil in the engine. Fill up gasoline and oil as instructed in the accompanying engine manual BEFORE operating your mower. Handle 1. Remove any packing material which may be between upper and lower handles. a. Pull up and back on upper handle as shown in Fig. 3-1.
ページ9に含まれる内容の要旨
a. Hold blade control against upper handle. b. Pull starter rope out of the engine. Release blade control handle. c. Slip starter rope into rope guide. d. Tighten wing nut. 4. Insert post on cable ties into holes provided on the lower handle. Pull cable tie tight and trim excess. A Grass Catcher 1. Follow steps below to assemble the grass catcher (if needed). Make certain bag is turned right side out before assembling (warning label will be on the outside). a. Place bag over frame so that
ページ10に含まれる内容の要旨
Side Discharge Chute Adjustments To convert to side discharge, make sure grass catcher is off of the Cutting Height unit, the rear mulch plug is removed, and rear discharge door is closed. 1. The cutting height adjustment lever is located above the rear left wheel. See Fig. 3-8. 1. On the side of the mower, lift the mulching plug. 2. Slide chute hooks under hinge pin on mulching plug assembly. Lower mulching plug. See Fig. 3-7. Do not remove side mulching plug at any time, even when you are
ページ11に含まれる内容の要旨
Controls and Features 4 Blade Control Recoil Starter Cutting Height Adjustment Lever Mulch Plug Figure 4-1 Recoil Starter Blade Control The recoil starter is attached to the right upper handle. Stand The blade control is attached to the upper handle of the mower. behind the unit and pull the recoil starter rope to start the unit. Depress and squeeze it against the upper handle to operate the unit. Release it to stop engine and blade. See Fig. 4-1. Mulching Plug WARNING: This blade control is
ページ12に含まれる内容の要旨
Operation 5 Starting Engine WARNING: Be sure no one other than the operator 3 is standing near the lawn mower while starting engine or operating mower. Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any moving parts on engine and lawn mower. 1. Place the fuel valve lever (if equipped) found on the left side of the engine into the ON (OPEN) position.
ページ13に含まれる内容の要旨
Maintenance & Adjustments 6 4. Follow the accompanying engine manual for lubrication Maintenance schedule and instruction for engine lubrication. General Recommendations Deck Care • Always observe safety rules when performing any Clean underside of the mower deck after each use to prevent maintenance. build-up of grass clippings or other debris. Follow steps below • The warranty on this lawn mower does not cover items that for this job. have been subjected to operator abuse or negligence. T
ページ14に含まれる内容の要旨
Replacing Rear Flap 1. To remove rear flap, lift rear door, and press flap in on either side to remove from hole. See Fig. 6-2. 1 2. Remove flap from opposite hole and replace with new flap in the opposite order and manner of removal. 2 Figure 6-2 14 s ce ti On 6— Maintenanec & a jdust Ments
ページ15に含まれる内容の要旨
Service 7 5. Lubricate the engine crankshaft and the inner surface of Blade Care the blade adapter with light oil. Slide the blade adapter WARNING: When removing the cutting blade for onto the engine crankshaft. Place the blade on the adapter sharpening or replacement, protect your hands with such that the side of the blade marked “Bottom” (or with part number) faces the ground when the mower is in the a pair of heavy gloves or use a heavy rag to hold the operating position. Make sure that
ページ16に含まれる内容の要旨
Troubleshooting 8 Problem Cause Remedy Engine Fails to start 1. Blade control disengaged. 1. Engage blade control. 2. Spark plug boot disconnected. 2. Connect wire to spark boot. 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh gasoline. 4. Engine not primed (if equipped with primer). 4. Prime engine as instructed in the Operation section. 5. Faulty spark plug. 5. Clean, adjust gap, or replace. 6. Blocked fuel line. 6. Clean fuel line. 7. Engine flooded. 7. Wait a few minutes to
ページ17に含まれる内容の要旨
Notes 9 17
ページ18に含まれる内容の要旨
Model Series 180 44 43 24 37 39 41 25 5 46 45 40 35 12 14 46 38 49 42 B 27 B 50 1 23 38 48 6 51 30 4 29 22 3 21 2 3 54 19 36 20 28 48 A 32 52 31 8 9 32 13 34 10 11 26 15 47 53 17 3 32 33 18 16 Wheel Tread A 7 18
ページ19に含まれる内容の要旨
Model Series 180 Ref Ref Part Number Description Part Number Description No. No. 1 787-01649 19” Deck 28 687-02228 Rear Bracket Assembly 29 710-3025 Hhcs, 5/16-18 x .625 2 731-05880 Spacer, .515 x 1.00 x .310 Lg. 30 710-1242 Screw, 5/16-14 x .750 3 710-1241 Screw, 1/4-15 x 1.000 4 710-0779A Screw, #10-16 x .500 31 712-04063 Nut, Flange Lock, 5/16-18 5 749-04037 Lower Handle 32 712-04065 Nut, Flange Lock, 3/8-16 33 634-04346 Front Wheel 6 710-0654A Screw, tt, 3/8-16 x 1.00 34 634-04347 Rear Whee
ページ20に含まれる内容の要旨
CUB CADET LLC MANUFACTURER’S LIMITED WARRANTY FOR WAL- k BEhIND MOWERS IMPORTANT: To obtain warranty coverage owner must present an Without limiting the foregoing, this limited warranty does not provide original proof of purchase and applicable maintenance records to the coverage in the following cases: servicing dealer. Please see the operator’s manual for information on a. The engine or component parts thereof. These items may carry a required maintenance and service intervals. separate ma
