ページ1に含まれる内容の要旨
2008-01
Illustrated
Parts List I0807220
531 30 83-24
40 Inch Front Mount Dethatcher
(45-0438)
Repair Parts Manual
ページ2に含まれる内容の要旨
™ OwNERs MANUAl Model No. 45-0438 40" FRONT MOUNT TINE DETHATCHER CAUTION: safety Read Rules for Assembly Operating Safe Operation and Instructions Maintenance Repair Parts Carefully the fastest way to purchase parts www.speedepart.com FORM NO. 40506 (REV. 2/28/07) PRINTED IN USA
ページ3に含まれる内容の要旨
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. • Read safety rules in the vehicle owners manual and • When de-thatching do not drive too close to a creek or know how to operate your equipment, before using the ditch and be alert for holes and other hazards which tine dethatcher. could cause you to lose control of the vehicle. • Never operate vehicle and tin
ページ4に含まれる内容の要旨
6 1 2 3 4 5 7 8 10 12 11 9 REF PART NO. QTY DEsCRIPTION REF PART NO. QTY DEsCRIPTION 1 44326 12 Carriage Bolt, 5/16-18 x 1" 7 43343 6 Hairpin Cotter, 1/8" 2 43063 2 Hex Bolt, 5/16-18 x 1" 8 46838 4 Spacer, .8" x 1" x .5" 3 43001 4 Hex Bolt, 3/8-16 x 1" 9 44044 1 Clevis Pin, 3/8" x 3/4" 4 43087 2 Hex Bolt, 3/8-16 x 1-1/4" 10 43055 1 Hairpin Cotter, 3/32" 5 43069 4 Carriage Bolt, 3/8-16 x 1-1/2" 11 47810 14 Nylock Nut, 5/16-18 6 R19212113 4 Flat Washer, 5/8" 12 HA21362 10 Nylock Nut, 3/8-16 17 15
ページ5に含まれる内容の要旨
• Remove any front mounted attachments which may Stop engine and let muffler cool before be installed on your tractor. attempting to install dethatcher hitch brackets. • Mark all loose parts and save for reassembly. 1 1 LEFT END 17 17 1 23 x 1 x 2 TINES POINT 11 TO FRONT x 2 11 2 23 16 16 1 11 x 2 x 4 1 x 4 11 3 13 14 4 14 1 11 x 1 1 x 4 x 2 11 12 x 4 12 x 2 4 13 x 2 4
ページ6に含まれる内容の要旨
4 26 7 APPLY OIL 24 6 x 1 x 1 6 7 26 24 x 2 x 1 5 6 7 7 6 x 2 x 1 6 7 20 x 1 20 7 x 2 5
ページ7に含まれる内容の要旨
ATTACHING DETHATCHER TO TRACTOR 7 • If the front of your tractor has front mounting holes as shown in figure 7, continue on to figure 8. • If the front of your tractor DOEs NOT have front mounting holes, go to figure 10. FRONT MOUNTING HOLES 8 • Remove two self threading bolts (if present) from SELF THREADING BOLT front cross-member of tractor. Assemble bolts through FRONT lower slots in hitch bracket, then reinstall them back into front crossmember. (Make sure notches at top of hitch brac
ページ8に含まれる内容の要旨
10 • Assemble the frame mount bracket (27) to the tractor frame using four 3/8" x 1-1/2" carriage bolts (5), 8 spacers (8) and 3/8" nylock nuts (12). The spacers (8) go between the tractor frame and the frame mount bracket. 12 5 27 11 21 11 1 1 22 x 1 x 2 21 22 11 x 2 x 1 12 FRONT 11 2 x 2 21 x 2 11 19 21 x 1 19 2 x 1 7
ページ9に含まれる内容の要旨
13 • Attach dethatcher to hitch plate by placing mounting FRONT OF TRACTOR shaft into slots at front of hitch plate. Dethatcher mounting arms go to inside of hitch plate. Assemble SLOT keeper plates onto ends of mounting shaft and secure with (large) 1/8" hairpin cotters. HITCH PLATE MOUNTING SHAFT (LARGE) 1/8" KEEPER HAIRPIN COTTER PLATE 14 15 18 10 x 1 15 x 1 18 22 17 10 21 x 1 9 x 1 17 9 x 1 15 • Raise and lock dethatcher in transport position (see operation instructions on pages 9 a
ページ10に含まれる内容の要旨
CUSTOMER RESPONSIBILITIES • Read and follow the maintenance schedule and the maintenance procedures listed in this section. MAINTENANCE SCHEDULE Fill in dates as you Service Dates complete regular service. Check for loose fasteners X Lubrication X CHECK FOR LOOSE FASTENERS LIFT HANDLE • Before each use check all nuts and bolts for tightness. Tighten loose fasteners before using. SMALL HAIRPIN COTTER LUBRICATION • Before each use apply a small amount of motor oil between washer and w
ページ11に含まれる内容の要旨
Leveling the dethatcher KNOW YOUR DETHATCHER • Move tractor with front mounted dethatcher onto a level surface, such as a drive or garage floor. • Lower dethatcher from transport position to rest on level surface. LIFT HANDLE • Loosen carriage bolts through mounting arms and angle brackets. (Refer to figure 3 on page 5.) • Adjust tine shield until spring tines come in contact with level surface, keeping front and back tines at same height. Tighten mounting arm carriage bolts on top of deth
ページ12に含まれる内容の要旨
40" TINE DETHATCHER MODEL 45-0438 11 18 1 22 27 5 15 8 21 12 2 12 10 16 7 9 1 3 17 1 19 11 12 25 7 20 13 23 7 25 11 A 7 A 1 7 16 6 13 4 14 11 6 28 11 6 24 6 29 26 7 REF PART NO. QTY DEsCRIPTION REF PART NO. QTY DEsCRIPTION 1 44326 12 Carriage Bolt, 5/16-18 x 1" 16 23666 2 Angle Mount Bracket 2 43063 2 Hex Bolt, 5/16-18 x 1" 17 62601 1 Lift Handle Bracket 3 43001 4 Hex Bolt, 3/8-16 x 1" 18 43943 1 Plastic Grip 4 43087 2 Hex Bolt, 3/8-16 x 1-1/4" 19 26168 1 Hitch Plate 5 43069 4 Carriage Bolt, 3/8
ページ13に含まれる内容の要旨
the fastest way to purchase parts www.speedepart.com REPAIR PARTs Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 © 2006 Agri-Fab, Inc. www.agri-fab.com
