ページ1に含まれる内容の要旨
OPERATOR'S MANUAL
GPS PLOTTER/SOUNDER
Model GP-1670F/GP-1870F
www.furuno.com
ページ2に含まれる内容の要旨
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A : JUN. 2012 All rights reserved. Printed in Japan C : FEB. 15, 2013 Pub. No. OME-44770-C (TAHA ) GP-1670F/GP-1870F *00017659312* *00017659312* * 0 0 0 1 7 6 5 9 3 1 2 *
ページ3に含まれる内容の要旨
IMPORTANT NOTICES General • This manual has been authored with simplified grammar, to meet the needs of international us- ers. • The operator of this equipment must read and follow the descriptions in this manual. Wrong op- eration or maintenance can cancel the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications ca
ページ4に含まれる内容の要旨
SAFETY INSTRUCTIONS The operator must read the safety instructions before attempting to operate the equipment. Indicates a potentially hazardous situation which, if not avoided, WARNING could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. CAUTION Warning, Caution Prohibitive Action Mandatory Action WARNING WARNING Do not open the equipment. Do not disassemble or modify the equipment. The equip
ページ5に含まれる内容の要旨
SAFETY INSTRUCTIONS CAUTION Do no turn on the equipment with the transducer out of water. The transducer can be damaged. The picture is not refreshed when picture advancement is stopped. Maneuvering the vessel in this condition can result in a dangerous situation. Adjust the gain correctly. Incorrect gain may give a wrong depth indication, which could result in a dangerous situation. The data presented by this equipment is intended as a source of navigation information. The prudent naviga
ページ6に含まれる内容の要旨
TABLE OF CONTENTS FOREWORD ...................................................................................................................ix SYSTEM CONFIGURATION ..........................................................................................xi EQUIPMENT LISTS.......................................................................................................xii 1. OPERATIONAL OVERVIEW .................................................................................1-1 1.1 Contro
ページ7に含まれる内容の要旨
TABLE OF CONTENTS 3.2.3 How to enter a position manually on the plotter screen .................................3-3 3.2.4 How to enter a point from the Points List .......................................................3-3 3.3 How to Find Detailed Point Information......................................................................3-4 3.4 How to Move a Point ..................................................................................................3-4 3.4.1 How to move a point on the sc
ページ8に含まれる内容の要旨
TABLE OF CONTENTS 6.3 3D Display..................................................................................................................6-6 6.3.1 3D display description.................................................................................... 6-6 6.3.2 How to tilt and rotate the 3D display .............................................................. 6-7 6.3.3 How to make the 3D view clearer ..................................................................6-7 6.4 Satellite
ページ9に含まれる内容の要旨
TABLE OF CONTENTS 9. MEMORY CARD OPERATIONS ...........................................................................9-1 9.1 The Memory Card Screen ..........................................................................................9-1 9.2 How to Initialize SD Cards..........................................................................................9-1 9.3 How to Eject an SD Card............................................................................................9-2 9.4 How t
ページ10に含まれる内容の要旨
TABLE OF CONTENTS 13.6.1 INSTALLATION SETTINGS menu.............................................................13-19 13.6.2 CAN bus input/output.................................................................................13-21 APPENDIX 1 MENU TREE .......................................................................................AP-1 APPENDIX 2 ABBREVIATIONS, SYMBOLS...........................................................AP-6 APPENDIX 3 JIS CABLE GUIDE ...............................
ページ11に含まれる内容の要旨
FOREWORD A Word to GP-1670F, GP-1870F Owners Congratulations on your choice of the FURUNO GP-1670F, GP-1870F GPS Plotter/Sounder. We are confident you will see why the FURUNO name has become synonymous with quality and re- liability. Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our ex- tensive global network of agents and dealers. This equipment is designed and co
ページ12に含まれる内容の要旨
FOREWORD Fish finder • Fish finder measures the depth to the bottom and displays underwater conditions in multi-col- ors* according to echo strength. A monochrome presentation shows the echoes in shades of gray. (*Number of colors depends on network sounder, color sounder.). • Automatic and manual fish finder operation. Auto mode automatically adjusts range, gain and clutter ac-cording to purpose - fishing or cruising. • Wide variety of zoom modes for detailed observation of fish and bottom. T
ページ13に含まれる内容の要旨
SYSTEM CONFIGURATION The environmental category of each unit is as follows: Unit Environmental category Display unit Protected from the weather GPS antenna unit Exposed to the weather, or protected from the weather in case of internal antenna Transducer, sensor Submerged in water Other units Protected from the weather GP-1670F Antenna Unit GPA-017 or GPA-017S Water temp./speed sensor ST-02MSB, ST-02PSB Display Unit Water temp. sensor OR GP-1670F T-02MSB, T-02MTB, T-03MSB CAN bus Junc
ページ14に含まれる内容の要旨
EQUIPMENT LISTS Standard supply Name Type Code no. Qty Remarks Display Unit GP-1670F - Select one Display Unit GP-1870F - Installation CP14-07100 000-021-070 1 set w/CP14-07101, MJ-A3SPF0013A- Materials 035C (power cable) Spare Parts SP14-03501 001-184-710 1 set Accessories FP14-03001 001-184-730 1 set For GP-1670F FP14-03201 001-183-120 1 set For GP-1870F Optional equipment Name Type Code no. Remarks Replacement Kit OP14-72 001-184-750 Waterproofing Cap LTWCAP-WBDMMSA1 000-167-169-11 Antenna Un
ページ15に含まれる内容の要旨
EQUIPMENT LISTS Name Type Code no. Remarks Temperature Sen- T-02MTB 000-040-026 Transom mount, 8 m cable sor T-02MSB 000-040-040 Thru-hull type T-03MSB 000-040-027 Thru-hull type, 8 m cable Matching Box MB-1100 000-041-353 For connection to 1 kW trans- ducer Rectifier PR-62 000-013-484 100 VAC Rectifier PR-62 000-013-485 110 VAC Rectifier PR-62 000-013-486 220 VAC Rectifier PR-62 000-013-487 230 VAC Junction Box FI-5002 Right Angle Mount- No.13QA330 001-111-910-10 ing Base L-angle Mounting No.13
ページ16に含まれる内容の要旨
EQUIPMENT LISTS Name Type Code no. Remarks Termination Resis- LTWMN-05AFFT- 000-160-509-10 Mini style, female, termina- tor (Mini) SL8001 tion resistor Termination Resis- LTWMC-05BFFT- 000-168-605-10 Micro style, female, termina- tor (Micro) SL8001 tion resistor Inline Terminator FRU-0505-FF-IS 001-077-830-10 Cable Assy. 02S4147-1 000-141-082 For speed/temp. sensor Inner Hull Kit 22S0191 000-082-598 w/installation instructions, not usable with the bottom discrimination display NMEA Data Con- I
ページ17に含まれる内容の要旨
1. OPERATIONAL OVERVIEW 1.1 Controls 1.1.1 Control description The controller for this system is either the GP-1670F or the GP-1870F. A key that has two text labels has two functions. The top label is the main function and the bottom label is the secondary function. Short-push to access the main function and long-push (approximately three seconds) to access the secondary function. You operate the chart plotter with • Keys • CursorPad TM • RotoKey • Menus, where you select options • Context-se
ページ18に含まれる内容の要旨
1. OPERATIONAL OVERVIEW Control Description TM Short push: Display the base RotoKey soft controls for the current RotoKey mode. Long push: Display the full RotoKey soft controls for the current mode. Rotate: Zoom in or out the display range for the chart. Select a menu item. Select the display range for the fish finder. POINTS/GO Short press: Put a point at the cursor position. TO key Long press: Set cursor position as destination. EVENT/ Short press: Put a point at the current position. MOB
ページ19に含まれる内容の要旨
1. OPERATIONAL OVERVIEW Tested SD cards The SD cards tested for use in this equipment are listed in the table below. Maker, Type Size 2 GB 4 GB 8 GB 16 GB 32 GB ADTEC AD-SDH (SD) [AD-SDH2G] Y BUFFALO RSDC-S (SD) [RSDC-S2G] Y RSDC-G Hi-Performance (SD) [RSDC-G2G] Y Hagiwara System T series (SD) [PSDB0487A] Y M series Super High Speed (SD) [PSDB0486A] Y I-O DATA I-O DATA (SD) [SD-2G] Y I-O DATA Super High Speed (SD) [SDP-2G] Y Kingston Kingston (SD) [SD/2GBFE] Y Kingston (SDHC) CLASS 4 [SD4/16GB]
ページ20に含まれる内容の要旨
1. OPERATIONAL OVERVIEW Maker, Type Size 2 GB 4 GB 8GB 16 GB 32GB San Disk SanDisk (SD) [SDSDB-2048-J60] Y SanDisk (SDHC) [SDSDBR-4096-J85] Y SanDisk Ultra II (SDHC) CLASS 4 [SDSDRH-8192-903] Y SanDisk Ultra II (SD) [SDSDH-2048-903] Y SanDisk Ultra II (SDHC) [SDSDRH-4096-903] Y SanDisk Extreme III (SDHC) [SDSDRX3-4096-903] Y SanDisk Extreme (SDHC) [SDSDX3-016G-J31A] Y SanDisk Extreme (SDHC) [SDSDX3-032G-J31A] Y SILICON POWER (SDHC) [SP016GBSDH006V10] Y (SDHC) [SP032GBSDH006V10] Y TOSHIBA (SD) C
