ページ1に含まれる内容の要旨
User’s Ｍａｎｕａｌ
POS Workstation
Model No. JS-950 Series
Contents
For USA / For CANADA
English
Read Me First …..….……..... 2
1.Getting Started
2.Operation
3.Appendix
Before operating this product,please read the instructions carefully,
and save this manual for future use.
ページ2に含まれる内容の要旨
■ For USA Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, If not installed and used in accordance with the i
ページ3に含まれる内容の要旨
English Read Me First Introduction Thank you for purchasing the JS-950 series Panasonic POS Workstation. This manual describes the instructions for the POS Workstation. Please read this manual carefully before using this product. List of JS-950 series Product Name Model Number. Remarks JS-950WS-040 CPU:3.2GHz,Memory:512MB or 1GB Main Unit POS Workstation JS-950WS-050 CPU:3.2GHz,Memory:2GB JS-950D2R010 12” resistive Touch screen JS-950D2C020 12” capacitive Touch screen Display
ページ4に含まれる内容の要旨
1. Getting Started ■ Precautions [POS Workstation: JS-950 series] IMPORTANT Install a socket outlet adjacent to the equipment so that it will be easily accessible. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 1. Avoid Radio Frequency Interference Do not place the POS Workstation near a television or radio receiver. 2. Avoid Stacking Do not place heavy objects on the POS Workstation. 3. Keep S
ページ5に含まれる内容の要旨
■ Name of each part & function 1 4 2 3 5 6 1. Operator’s Display 2. Front SW cover 3. POP Holder 4. Rear Display 5. USB connector 6. Power SW Attention: Do not push Power SW by mistake when you insert the USB connector. 4
ページ6に含まれる内容の要旨
2. Operation ■ AC Cord Kit Installation 1. How to install the AC Cord (1) Carefully lay the Main Body Unit on a clear, flat surface as shown in figure (1). (2) Unpack the AC Cord, and then connect it to AC Inlet as shown in figure (2). (3) Fit the Cord Clamp to AC Cord, and fix it by attached screw as shown in figure (3)-1, 2 and 3. (4) Carefully replace the Main Body Unit in upright position as shown in figure (4). (1) (2) (3)-1 AC Inlet (3)-2 (3)-3 (4)
ページ7に含まれる内容の要旨
■ Display Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to install the display unit (1) Open the screw cover of the main unit (POS Workstation). (2) Hold the display unit with both hands and insert the connector section of the display unit into the connector inlet guide of the main unit slowly to connect the connector. Note: When the connector section is connected
ページ8に含まれる内容の要旨
■ Storage Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the storage unit (1) Disconnect the 2 latches on the upper portion of the filter cover of the main unit by both hands, pull the cover toward you while pressing the cover downward at the same time, and remove the filter cover. (2) Insert the storage unit into the prescribed inlet of the main unit slowly
ページ9に含まれる内容の要旨
■ Rear Display Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the rear display unit (1) Loosen the thumbscrew on the lower portion of the rear cover at the rear display side of the main unit by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Prepare a rear display to be used. (The contents
ページ10に含まれる内容の要旨
2. How to replace the rear display (1) Loosen the thumbscrew on the lower portion of the rear cover of the main unit by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Disconnect the connector of the rear display from the connector of the main unit. (3) Loosen the 2 thumbscrews securing the rear display, and remove the rear display. * The thumbscrews shall be loosened until the screws rotate without resistance. (4)
ページ11に含まれる内容の要旨
■ 2nd display unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the 2nd Display Unit (1) Loosen the thumbscrew on the lower portion of the rear cover at the rear display side of the main block by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Prepare a 2nd display unit to be used. (The conte
ページ12に含まれる内容の要旨
2. How to replace the 2nd Display Unit (1) In case of 950SD010, disconnect VGA cable and speaker cable from I/O panel. (2) Loosen the thumbscrew on the lower portion of the rear cover of the main block by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (3) Disconnect the connector of the 2nd Display Unit from the connector of the main block. (4) Prepare a new rear display. (5) Follow the steps (3), (4) and (5) of “How to
ページ13に含まれる内容の要旨
■ ID module Unit installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. Contents Peripheral screw Cable cover (Use only ID module 1pcs Screw 2pcs 2pcs Long type 1pcs Dallas KEY reader) Short type 1pcs Cable clamp 1pcs 2. How to mount the ID module unit (Please see the following pictures.) (1) Place the main unit to make the display unit at right angle to the mo
ページ14に含まれる内容の要旨
Tighten the screw to clamp the cable and wiring the cable as shown in the fig. (10)-4. (11) Slide USB cable cover as shown in the fig. (11)-1. In case of Dallas KEY reader, slide the USB cable cover with care to avoid the cable from the rib of the USB cable cover as shown in the fig. (11)-2. (12) Put the supplied 2 peripheral screws in from the front side of the ID module unit and tighten the screws using a screwdriver from the rear side to secure it. (13) Install Display Unit according
ページ15に含まれる内容の要旨
(11)-1 (11)-2 (12) Rib 3. How to replace the ID module unit (1) Remove Display Unit according to Display Unit Installation. (2) Prepare an ID module unit to be used. * The ID module unit is supplied with 2 pieces of peripheral screws, 2 pieces of screws, 1 piece of long cable cover, and 1 piece of short cable cover as accessories. (3) Slide the USB cable cover toward you while pushing both sides of the USB cable cover at the hinge section of the display unit inward to
ページ16に含まれる内容の要旨
3. Appendix ■ Specifications [Common Specifications] Environmental condition Item Specification Operating Temperature +5°C – +40°C Operating Humidity 15% RH – 85% RH (no dew) Strage Temperature -30°C – +60°C Strage Humidity 10%RH – 90%RH [POS Workstation: JS-950WS- ・・・ ] Item Specification Power Supply input AC100V-240V, 50/60 Hz, 6.0A Size Approx. W250mm x D277mm x H351mm Mass Approx. 7.0 kg Standard Safty cULus, TÜV, CE, GOST, BSMI, SABS EMI & FCC Part15 Class A,
ページ17に含まれる内容の要旨
IO Connector layout (1) Bottom IO Connector layout USB4(+24V) COM 3 LINE-OUT Printer LAN (Powered) MIC USB3(+12V) ○○○○ ○ ○○○○ ○○○○ ○ ○○○○ ○○○○ ○○○○ ○ ○○○ ○○○○ ○○○○ ○ ○○○○ ○ ○○○○ ○ ○○○○ ○ ○○○○ ○ ○○○○ ○○○○ ○○○○ ○ ○○○○ C/D2 USB1 USB2 COM 2 C/D1 COM 1 COM 4 VGA (Powered) (2) Rear Display Connector Layout Top of main block VFD 2lines (COM6) 2nd Display T/P & VFD 4 Lines (COM6) (3) Front IO Connector layout SW & LED USB #5 LAN L
ページ18に含まれる内容の要旨
Outside drawing Main Body 12” Touch Screen 15” Touch Screen 17
ページ19に含まれる内容の要旨
[Touch Display Unit: JS-950D・・・・・ ] Item Specification Size 12.1”: Approx. W320mm x D153mm x H256mm 15”: Approx. W364mm x D153mm x H300mm Mass 12.1”: Approx. 3.4 kg 15”: Approx. 4.4 kg Outside drawing (1) 12.1” resistive TP Display, 12.1” capacitive TP Display (2) 15” resistive TP Display, 15” capacitive TP Display 18
ページ20に含まれる内容の要旨
[Storage module Unit: JS-950H・・・・・ ] Item Specification Size Approx. W171mm x D126.5mm x H34mm Mass Approx. 0.8Kg (3.5”), 0.5Kg(2x CF) Outside drawing 3.5HDD module, Dual CF module 19
