ページ1に含まれる内容の要旨
Dell Precision Workstation T7600
Owner's Manual
Regulatory Model: D02X
Regulatory Type: D02X001
ページ2に含まれる内容の要旨
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2012 Dell Inc. ™ ™ ™ ™ ™ ™ Trademarks used in this text: Dell , the DELL logo, Dell Precision , Precision ON ,ExpressCharge , Latitude , Latitude ON , ™ ™ ™ ® ® ®
ページ3に含まれる内容の要旨
Contents Notes, Cautions, and Warnings...................................................................................................2 1 Working on Your Computer.......................................................................................................7 Before Working Inside Your Computer.....................................................................................................................7 Turning Off Your Computer...................................................
ページ4に含まれる内容の要旨
Removing the Front I/O Panel and the USB 3.0 Ports.............................................................................................31 Installing the Front I/O Panel and the USB 3.0 Ports..............................................................................................33 Removing the Power Switch...................................................................................................................................33 Installing the Power Switch...................
ページ5に含まれる内容の要旨
Errors That Do Not Halt Your Computer...........................................................................................................66 Errors That Soft Halt Your Computer................................................................................................................66 7 Technical Specifications.........................................................................................................69 8 Contacting Dell....................................................
ページ6に含まれる内容の要旨
6
ページ7に含まれる内容の要旨
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse orde
ページ8に含まれる内容の要旨
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1. Shut down the operating system: – In Windows 7: Click
ページ9に含まれる内容の要旨
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe Removing the Power Supply Unit (PSU) 1. Follow the procedures in Before Working Inside Your Computer. 2. If the PSU is locked, remove the screw to unlock the PSU. For more information, see the PSU
ページ10に含まれる内容の要旨
Removing the Front Cover NOTE: The front cover can be secured using the front panel-chassis lock. For more information the front-panel chassis lock, see Additional Information — Front Panel Chassis Lock. 1. Follow the procedures in Before Working Inside Your Computer. 2. Press down on the front cover release latch. Figure 2. 3. Keep the latch pushed down, and pull the front cover in an outward direction to remove it from the computer. Figure 3. 10
ページ11に含まれる内容の要旨
Installing the Front Cover 1. Place the front cover on the computer. 2. Press down on the front cover till it clicks into place. 3. Follow the procedures in After Working Inside Your Computer. Removing the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the front cover. 3. Pull the clasp of the hard-drive bracket in an outward direction. Figure 4. 4. Slide the hard-drive bracket in an outward direction to remove it from the computer. 11
ページ12に含まれる内容の要旨
Figure 5. 5. If a second hard drive is installed, Pull the clasp of the second hard drive bracket in an outward direction. Figure 6. 6. Slide the second hard-drive bracket in an outward direction to remove it from the computer. 12
ページ13に含まれる内容の要旨
Figure 7. 7. Flex the hard-drive bracket on both sides to loosen the hard drive. Figure 8. 8. Lift the hard drive in an upward direction to remove it from the hard drive bracket. Figure 9. 13
ページ14に含まれる内容の要旨
9. If a 2.5 inch hard drive is installed , Push the retention clips in an outward direction and lift up the drive to remove it from the 3.5 inch hard-drive caddy. Figure 10. Installing the Hard Drive 1. Flex the hard drive-bracket and then insert the hard drive into the bracket. 2. Slide the hard-drive bracket into its compartment and close the hard-drive bracket clasp. 3. Install the front cover. 4. Follow the procedures in After Working Inside Your Computer. Removing the Left Cover 1. Follow
ページ15に含まれる内容の要旨
Figure 12. Installing the Left Cover 1. Place the computer cover on the chassis. 2. Press down on the cover till it clicks into place. 3. Follow the procedures in After Working Inside Your Computer. Removing the Intrusion Switch 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the left cover. 3. Press the intrusion switch release latch and disconnect the connector from the system board. a) Unroute the intrusion switch cable from the chassis. Figure 13. 15
ページ16に含まれる内容の要旨
4. Push the intrusion switch downwards and remove it from the computer. Figure 14. Installing the Intrusion Switch 1. Install the intrusion switch into its place holder on the chassis. 2. Route the intrusion switch cable around the chassis clips and install the connector to the system board. 3. Install the left cover. 4. Follow the procedures in After Working Inside Your Computer. Removing the PCI Card 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the left cover. 3.
ページ17に含まれる内容の要旨
Figure 16. Installing the PCI Card 1. Push the expansion card into the card slot and secure the latch. 2. Install the plastic latch that secures the PCI card to the card slot. 3. Install the left cover. 4. Follow the procedures in After Working Inside Your Computer. Removing the Optical Drive 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the left cover. 3. Disconnect the data cable from the back of the optical drive. 17
ページ18に含まれる内容の要旨
Figure 17. 4. Disconnect the power cable from the back of the optical drive. Figure 18. 5. Press down on the blue release tab to release the latches that secure the optical drive. 18
ページ19に含まれる内容の要旨
Figure 19. 6. Slide the optical drive out of its compartment and lift it up to remove it from the computer. Figure 20. 7. Flex the optical drive bracket latches in an outward direction to loosen the optical drive from the bracket. Figure 21. 19
ページ20に含まれる内容の要旨
8. Lift the optical drive and remove it from the bracket. Figure 22. Installing the Optical Drive 1. Slide the optical drive into its compartment and ensure it is seated firmly. 2. Connect the power cable and the data cable to the back of the optical drive. 3. Install the left cover. 4. Follow the procedures in After Working Inside Your Computer. Removing the Air Tunnel NOTE: The air tunnel is an optional component and your computer may not ship with it. 1. Follow the procedures in Before Worki
