ページ1に含まれる内容の要旨
OWNER’S
MANUAL
Model No.
200.71210
10/2 AMP
MANUAL
BATTERY CHARGER
CAUTION:
Read and Follow All Safety
Rules and Operating Instructions
Before Every Use of this Product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
ページ2に含まれる内容の要旨
Table Of Contents Using Your Battery Charger .................................... 6 Warranty .................................................................. 1 Setting the controls ................................................ 6 Important Safety Instructions ................................. 2 Charging your battery ............................................ 6 Parts......................................................................... 3 Calculating charge time ...........
ページ3に含まれる内容の要旨
Important Safety Instructions – SAVE THESE INSTRUCTIONS – w To reduce the risk of explosion, explosive gases, or injury while ! WARNING using your battery charger, follow the precautions listed below: Read all instructions and cautions printed Do not disassemble charger. Take it to a on the battery charger, battery, and vehicle or qualified service professional if service or equipment using battery. repair is required. Incorrect assembly may result in fire or electrical shock. Use charge
ページ4に含まれる内容の要旨
Parts This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Replacement Parts List Sears 71210 Item Description Part Number 1 Cover 3799001402 2 Heatsink/Diode Assembly 2299000825 3 Base 3799001382 4 AC Power Cord 90026058 5 Transformer 93026336 6 Output Cable 3899000016 7 Circuit Breaker (20A) 3999000045 8 50A Clamp (1) 2299000248 Sleeving Red (2) required 0399000007 Sleeving Black (2) required 03990
ページ5に含まれる内容の要旨
Before Using Your Battery Charger It is important to understand your charger's requirements. This section will tell you about your charger's electrical requirements and how to prepare a battery for charging. Plugging it in ! WARNING Electrical Shock Hazard Be sure that power cord fits properly into outlet. If not, have a qualified technician install a proper outlet. Never alter the AC cord or plug provided. Improper connection can result in electrical shock. Your charger should be grounded to
ページ6に含まれる内容の要旨
Preparing your battery to be charged It is important that you read and follow these guidelines while you are preparing to charge your battery. Make sure that you have a 12 volt lead-acid battery. Clean the battery terminals. Be careful to keep corrosion from getting in or around your eyes. If you have a battery with removable cell caps, if required, add distilled water to each cell until the battery acid reaches the level recommended by the manufacturer. This will help purge excessive gase
ページ7に含まれる内容の要旨
Using Y Using Your Battery Charger our Battery Charger Using Y Using Y Using Your Battery Charger our Battery Charger our Battery Charger For best results from your battery charger, learn to use it properly. This section tells how to set the controls and how to charge a battery in or out of the vehicle. Setting the Controls SELECTOR SWITCHES: A 2-way switch is used to select the 2-AMP or the 10-AMP charge rate. AMMETER: 10 AMP 2 AMP The AMMETER indicates the measured amount of amperes being
ページ8に含まれる内容の要旨
6. Connect the clamp to the battery post and twist or rock back and forth to make a solid connection. This will help keep the clamps from slipping off the posts and causing sparks. 7. Select the charge rate with the Selector Switch then plug the power cord into a grounded AC outlet to begin charging. 8. The charger will not stop when the battery is fully charged. For this reason it is important to check charging progress frequently. Overcharging can damage a battery, you must monitor and unplug
ページ9に含まれる内容の要旨
Calculating charge time Calculating charge time Calculating charge time Calculating charge time Calculating charge time The Chart Method The Chart Method The Chart Method The Chart Method The Chart Method Use the following table to more accurately determine Marine, or deep-cycle batteries are usually rated in the time it will take to bring a battery to full charge. Reserve Capacity (RC). First, identify where your battery fits into the chart. NR means that the charger setting is NOT Small
ページ10に含まれる内容の要旨
Maintenance and care Maintenance and care Maintenance and care Maintenance and care Maintenance and care A minimal amount of care can keep your battery charger working properly for years. 1. Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps to prevent corrosion. 2. Coil the input and output cords neatly when storing the charger. This will help prevent acci- dental damage to the cords and charger. 3. Occasional cleanin
ページ11に含まれる内容の要旨
Troubleshooting Performance problems often result from little things that you can fix yourself. Please read through this chart for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No ammeter reading. Clamps not making good Check for poor connection at battery. Make sure clamps connection. and posts are clean. 2-amp charge rate. Ammeter needle will indicate little activity at the 2-amp charge rate. No AC power reaching Check AC outlet and extension cords for loos
ページ12に含まれる内容の要旨
10/2 AMP MANUAL OWNER’S BATTERY CHARGER MANUAL Model No. 200.71210 For information about troubleshooting Call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm CST Monday through Friday 1-800-SEARS-64 (1-800-732-7764) For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For the location of a Sears Repair Service Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222 When requesting service or ordering parts, always provid
