ページ1に含まれる内容の要旨
OWNER’S MANUAL
Model 6000A
For 12-Volt Batteries
™
SpeedCharge
computer
smart
™
amp amp
SLOW RAPID
2 30
CHARGE CHARGE
amp amp
FA S T ENGINE
CHARGE START
10 60
Fully Automatic
Microprocessor Controlled
Battery Charger with
Engine Starter plus
Battery Tester and
Alternator Tester
CAUTION:
Read all Safety Rules and Operating Instructions,
and follow them with each use of this product.
Schumacher Electric Corporation
Mount Prospect, IL 60056 U.S.A.
Send Warranty Product Repairs to:
Customer Service
ページ2に含まれる内容の要旨
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS .................................................................... 3 PERSONAL SAFETY PRECAUTIONS ...................................................................... 4 BEFORE USING YOUR BATTERY CHARGER ......................................................... 5 PLUGGING IT IN.................................................................................................. 5 USING AN EXTENSION CORD ...............................................
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS WARNING – RISK OF EXPLOSIVE GASES WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BAT- TERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY. To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of any equipment you intend to use in vic
ページ4に含まれる内容の要旨
Never place charger directly above Be sure to position the charger power battery being charged. The gases from cord to prevent it from being stepped the battery will corrode and damage the on, tripped over, or damaged. charger. Never pull out the plug by the cord Never touch the battery clamps together when unplugging the SpeedCharge. when the charger is on. You could Pulling on the cord may cause damage cause a spark. to the cord or the plug. Never operate charger if it has received Do not oper
ページ5に含まれる内容の要旨
BEFORE USING YOUR BATTERY CHARGER It is important to understand the charger’s requirements. This section explains the charger’s electrical requirements and how to prepare a battery for charging. extension cord, please make sure that PLUGGING IT IN Your charger requires a 120V AC you follow these guidelines: receptacle installed according to all local Make sure that pins on plug of codes and ordinances. extension cord are the same number, size, and shape as those of plug on charger. Check tha
ページ6に含まれる内容の要旨
OPERATING INSTRUCTIONS IMPORTANT: Follow all safety instructions and precautions when charging your battery. Wear complete eye protection and clothing protection. Charge your battery in a well-ventilated area. CHARGING BATTERY IN THE heavy, unpainted metal part of the VEHICLE: chassis or engine block, away from the battery (see figure above). DO 1. Avoid personal injury by keeping NOT connect clamp to negative clear of fan blades, belts, pulleys and battery post, carburetor, fuel line or other e
ページ7に含まれる内容の要旨
CHARGING BATTERY REMOVED 7. To disconnect the Charger, unplug its power cord before attempting to FROM THE VEHICLE: disconnect the charger clamps. Then, POSITIVE NEGATIVE standing away from the battery, remove the output clamp from the BATTERY CHARGER NEGATIVE battery post. Finally, BATTERY remove the output clamp from the POSITIVE battery post. POWER CORD 8. Clean and store the charger in a dry 24", 6 GAUGE CABLE location. TO GROUNDED USING ENGINE START POWER OUTLET Your battery charger can be
ページ8に含まれる内容の要旨
SPEEDCHARGE CONTROL Display Charge Battery ™ Rate Mode Type SpeedCharge LEDs LEDs LEDs Digital LED Status LEDs Switch Buttons 6000A CONTROL PANEL run down battery. Always use in DISPLAY MODE SWITCH combination with a battery. Use this switch to set the function of the digital LED to one of the following three. BATTERY TYPE SWITCH BATTERY %: The digital LED Use this switch button to set the type of displays an estimate of the percent of battery to be charged to one of the charge of the ba
ページ9に含まれる内容の要旨
CONTROL PANEL GUIDE 9 6000A CONTROL PANEL GUIDE MODE OF OPERATION Digital Display Initial power-up, battery not detected O O O 0.0 User selected User selected User selected No battery or reversed battery detected O 0% or 0.0V Battery tester activated O User selected 0~100% User selected Battery tester with charged battery O O 100% Battery tester with no battery O O User selected 0% Voltage meter activated O User selected 0.0~17.0V Alternator tester activated O User selected 0~199% Alternator t
ページ10に含まれる内容の要旨
USING THE BUILT-IN BATTERY TESTER OVERVIEW TESTING AFTER CHARGING The SpeedCharge has a built-in battery After the unit has been changed from tester that displays either an accurate tester to charger (by selecting a charge battery voltage or an estimate of the rate), it remains a charger as long as it battery’s relative charge based on the has power. Disconnect and reconnect battery voltage and the Battery Council the power to change the unit back to a International scale. tester. TESTING SEQUEN
ページ11に含まれる内容の要旨
USING THE BUILT-IN ALTERNATOR TESTER The SpeedCharge has a built-in display mode button to set the tester alternator tester that displays either an to “Alternator %” and read the accurate alternator voltage or an alternator percent. estimate of the alternator’s relative TESTER STATUS LEDs output compared to normal alternators. When the 6000A is operating as an The Alternator % values displayed alternator tester, the status LEDs light should be taken as general reference, under the following cond
ページ12に含まれる内容の要旨
while waiting and will reset if the display indicates the remaining cool engine is not cranked within 10 down time in seconds. It starts at 120 minutes. (If the charger resets, it sets and counts down to 0. The 60A itself for a 2A charge and REGULAR START LED blinks once every battery.) While waiting for cranking, second. During the cool down period, the digital display shows the battery the charger delivers charge at a rate voltage (it can’t be set to percent). of 10A and the CHARGING LED is li
ページ13に含まれる内容の要旨
30A CHARGE RATE: When set to MAINTAIN MODE: When the 30A10A, the unit will charge the CHARGED (green) LED is lit, the battery for a few minutes at 10A. The charger has started Maintain Mode. This charger will determine whether to mode of operation is also known as increase the current to 30A, based on Float-Mode Monitoring. In this mode, factors including the battery voltage and the charger keeps the battery fully type selected. If the current is increased charged by delivering a small current
ページ14に含まれる内容の要旨
BATTERY PERCENT AND CHARGE TIME This charger adjusts the charging time There are some important facts to keep in order to charge the battery com- in mind when charging a battery. pletely, efficiently and safely. The When the display indicates 77% microprocessor automatically makes charged, the battery has been the necessary decisions. However, this charged enough to start most vehicles section includes guidelines that can be and has already been charged as used to estimate charging times. much
ページ15に含まれる内容の要旨
TROUBLESHOOTING Performance problems often can be corrected by the user. Please read through this chart for a possible solutions to common problems. PROBLEM POSSIBLE CAUSE SOLUTION The battery is connected The SpeedCharge is in Press the CHARGE RATE and the charger is on, tester mode, not charger button to activate charging but it isn’t charging. mode. and select a charge rate. Indicator lights are lit in an The charger may be Return to place of pur- erratic manner not defective. chase for repla
ページ16に含まれる内容の要旨
LIMITED WARRANTY SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPECT, ILLINOIS 60056-2179 MAKES THIS LIMITED WARRANTY TO THE ORIGINAL PURCHASER AT RETAIL OF THIS PRODUCT. THIS LIMITED WARRANTY IS NOT TRANSFERABLE. Schumacher Electric Corporation warrants this battery charger for five years from date of purchase at retail against defective material or workmanship. If such should occur, the unit will be repaired or replaced at the option of the manufacturer. It is the obliga
