ページ1に含まれる内容の要旨
Dell ™ Vostro ™ V130 Service Manual
Regulatory Model: Regulatory Model: P16S
ページ2に含まれる内容の要旨
2
ページ3に含まれる内容の要旨
Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have performed the steps in Working on Your Computer. • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--inst
ページ4に含まれる内容の要旨
8. Turn the computer top-side up. 9. Open the display. 10. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display. CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which
ページ5に含まれる内容の要旨
1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard. 2. Connect any telephone or network cables to your computer. CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 3. Replace the battery. 4. Connect your computer and all attached devices to their electrical outlets. 5. Turn on your computer. 5
ページ6に含まれる内容の要旨
6
ページ7に含まれる内容の要旨
Battery Removing The Battery 1. Follow the procedures in Before Working On Your Computer. 2. Remove the Secure Digital (SD) card. 3. Remove the base cover. 4. Lift the black cable-release clip to release the battery cable from the connector on the system board and disconnect the battery cable. 5. Remove the screws that secure the battery to the computer. 6. Lift the battery up and away from the computer. NOTE: To replace the battery, see Installing The Battery. 7
ページ8に含まれる内容の要旨
Installing The Battery NOTE: To remove or locate the battery, see Removing The Battery. 1. Place the battery into the battery bay. 2. Replace and tighten the screws that secure the battery to the computer. 3. Connect the battery cable to the system board and press down the cable-release clip to lock the battery cable. 4. Install the base cover. 5. Install the Secure Digital (SD) Card. 6. Follow the procedures in After working inside your computer. 8
ページ9に含まれる内容の要旨
Secure Digital (SD) Card Removing The Secure Digital (SD) Card 1. Follow the procedures in Before Working On Your Computer. 2. Press in on the SD card to release the SD card from the computer. 3. Slide the SD card out of the computer. 9
ページ10に含まれる内容の要旨
NOTE: To install the SD card, see Installing The Secure Digital (SD) card. Installing the Secure Digital (SD) Card NOTE: To remove or locate the Secure Digital card, see Removing the Secure Digital (SD) card. 1. Slide the SD card into its slot until it clicks into place. 2. Follow the procedures in After working inside your computer. 10
ページ11に含まれる内容の要旨
Base Cover Removing The Base Cover 1. Follow the procedures in Before Working On Your Computer. 2. Remove the Secure Digital (SD) Card. 3. Remove the screws that secure the base cover to the computer. 4. Slide the base cover towards the front of the computer. Lift it up and away from the computer. NOTE: To replace the base cover see, Installing The Base Cover. Installing The Base Cover NOTE: To remove or locate the base cover, see Removing The Base Cover . 1. Slide the base cover to align the sc
ページ12に含まれる内容の要旨
12
ページ13に含まれる内容の要旨
Hard Drive and Audio Board Removing The Hard Drive And Audio Board Assembly 1. Follow the procedures in Before Working On Your Computer. 2. Remove the Secure Digital (SD) card. 3. Remove the base cover. 4. Remove the battery. 5. Disconnect the speaker and system board cables from the audio board. 6. Remove the screws that secure the audio board and the hard drive to the computer. 7. Lift and remove the hard drive and audio board assembly from the computer. 13
ページ14に含まれる内容の要旨
8. Slide the audio board from the hard drive. 9. Remove the screws that secure the hard-drive bracket to the hard drive. 14
ページ15に含まれる内容の要旨
10. Remove the hard drive from the hard-drive bracket. NOTE: To install the audio board and the hard drive, see Installing The Hard Drive And Audio Board Assembly. Installing The Hard Drive And Audio Board Assembly To remove or locate the hard drive and audio board, see Removing The Hard Drive And Audio Board Assembly. 1. Attach the hard-drive bracket to the hard drive. 2. Tighten the screws to secure the hard-drive bracket to the hard drive. 3. Connect the audio board to the hard drive. 4. Tigh
ページ16に含まれる内容の要旨
16
ページ17に含まれる内容の要旨
Coin-Cell Battery Removing The Coin-Cell Battery 1. Follow the procedures in Before Working on Your Computer. 2. Remove the Secure Digital (SD) card. 3. Remove the base cover. 4. Remove the battery. 5. Remove the card-reader board. 6. Disconnect the coin-cell battery cable from the system board. 7. Release and remove the coin-cell battery from the computer. NOTE: To replace the coin-cell battery, see Installing The Coin-Cell Battery. Installing The Coin-Cell Battery NOTE: To remove or locate the
ページ18に含まれる内容の要旨
2. Connect the coin-cell battery cable to the system board. 3. Install the card-reader board. 4. Install the battery. 5. Install the base cover. 6. Install the secure digital (SD) card. 7. Follow the procedures in After working inside your computer. 18
ページ19に含まれる内容の要旨
Wireless Local Area Network (WLAN) Card Removing The Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the Secure Digital (SD) card. 3. Remove the base cover. 4. Remove the battery. 5. Disconnect the antenna cables from the WLAN card. 6. Remove the screw that secures the WLAN card to the computer. 7. Slide and remove the WLAN card out from its slot on the system board. NOTE: To install the WLAN card, see Installing The Wireless Local A
ページ20に含まれる内容の要旨
Installing The Wireless Local Area Network (WLAN) Card NOTE: To remove or locate the WLAN card, see Removing The Wireless Local Area Network (WLAN) Card. 1. Insert the WLAN card into its connector at a 45–degree angle. 2. Replace and tighten the screw that secures the WLAN card to the computer. 3. Connect the black and white antenna cables to their respective connectors marked on the WLAN card. 4. Install the battery. 5. Install the base cover. 6. Install the Secure Digital (SD) card. 7. Follow
