ページ1に含まれる内容の要旨
PowerBook G4
AirPort Card
Installation Instructions
Be sure to follow the instructions in this sheet carefully. Failure to follow
these instructions could result in damage to your equipment and may void
your warranty.
Warning: Sharp edges may exist inside your computer and on any parts
you may remove or install. Use caution to avoid injury.
Installing an AirPort Card requires these basic steps:
• Turn off the computer.
• Remove any cables and the battery.
• Remove the bottom
ページ2に含まれる内容の要旨
Opening the Computer 1. Place your computer on a clean, flat surface. 2. Shut down your computer. Disconnect the power cord and any other cables connected to the computer. Warning: Always turn off your computer before opening its case to avoid damaging its internal components. Warning: The internal components of your PowerBook may be hot. If you have been using your PowerBook, wait 30 minutes after shutting it down to let the internal components cool before continuing. 3. Place a towe
ページ3に含まれる内容の要旨
5. Slide the battery compartment latch to remove the battery. Make sure to return the battery latch fully to the right. Removing the battery will help you remove the bottom case and prevent you from accidentally turning on the computer while installing the AirPort Card. 6. Using a Phillips screwdriver, remove the eight screws that secure the bottom case to the PowerBook (in the order shown in the illustration below). Important: To avoid damaging the case, be careful that the screwdri
ページ4に含まれる内容の要旨
7. To remove the bottom case you will need to disengage it at the left and right sides, then carefully pivot it forward to release a retaining clip near the DVD drive slot, as follows. Important: Do not push on the rubber feet of the bottom case. At the left side, carefully slide the bottom case slightly up and away from you by pushing on it just above the hinge of the display, and at the same time from within the battery compartment, pushing away from you on the edge of the bottom ca
ページ5に含まれる内容の要旨
8. When both the left and right sides have released, carefully pull up on the bottom case at the edge that is closest to you and rotate it away from you, pivoting evenly over the front edge to release a retaining clip that is located near the DVD drive slot. Important: Do not force, twist or pry the bottom case if it binds or resists. The case should remove easily. If not, follow step 7 again, until the case releases. Installing the AirPort Card 1. Touch the computer’s inside fra
ページ6に含まれる内容の要旨
2. If removing an existing AirPort Card (if not, skip to step 3), pull back on the antenna clip to release the antenna connector and allow the card to rise up slightly, then pull the card from the AirPort connector. Hold the AirPort Card with one hand and grasp the antenna cable connector with the other. While being careful not to strain the antenna cable, firmly pull the connector straight out of the AirPort Card. AirPort Card Connector Antenna Cable Antenna Clip Antenna Cable Connec
ページ7に含まれる内容の要旨
4. If this is a new installation, pull out the AirPort antenna cable connector from its holder. Antenna Cable Connector Holder Antenna Cable Connector 5. Pull up on the top part of the AirPort Card connector at the insertion end to raise it up slightly, if it is not already up. 6. Position the AirPort Card with the AirPort ID numbers and bar code facing up and slide the card into the connector. Make sure to slide the card all the way in until the card is securely attached to the connecto
ページ8に含まれる内容の要旨
7. Plug the antenna cable connector into the port, which is located just below the plastic tab, on the end of the AirPort Card. Make sure the connector is straight before inserting it into the card. 8. Push the AirPort Card down into its space until the antenna cable connector is secured by the small antenna clip. Important: Route the antenna cable between the edge of the computer and the AirPort Card. Verify that the cable is away from the edge of the computer so that it will not b
ページ9に含まれる内容の要旨
Closing the Computer 1. To attach the bottom case, align the notches on the right and left sides of the case (some of these can be viewed through the battery opening). Then press down and toward you slightly to secure the case. Verify that the case lies flat and fits properly around the battery latch and that the alignment tab that protrudes on the underside of the bottom case, shown in the illustration below, has seated properly. The case edges should line up smoothly. Note: A
ページ10に含まれる内容の要旨
4. Replace the battery. 5. Turn the computer over so that the DVD slot faces you. Just below the center of the DVD slot, verify that the bottom case is flush with the front edge of the slot. If the case is slightly bowed and there is a gap, carefully pull the bottom edge of the DVD slot until it clicks into place and becomes flush with the bottom case. DVD slot Gap 6. Reconnect the power cord and any other cables. Restart your computer. Warning: Never turn on your computer unless all of
ページ11に含まれる内容の要旨
Apple Computer, Inc. © 2001 Apple Computer, Inc. All rights reserved. Under the copyright laws, this document may not be copied, in whole or in part, without the written consent of Apple. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal