ページ1に含まれる内容の要旨
SWITCHER PROCESSOR PACK
MVS8000SF-C
MULTI FORMAT SWITCHER PROCESSOR
MVS-8000SF
HK-PSU04
MKS-8110HD MKS-8110SD MKS-8110M
MKS-8160HD MKS-8160SD MKS-8160M
MKS-8170HD MKS-8170SD MKS-8170M
MKS-8210HD MKS-8210SD MKS-8210M
MKS-8440HD MKS-8440SD MKS-8440M
MKS-8210K1 MKS-8440K1 MKS-8420M
INSTALLATION MANUAL
1st Edition (Revised 2)
ページ2に含まれる内容の要旨
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, F
ページ3に含まれる内容の要旨
Attention-when the product is installed in Rack: 1. Prevention against overloading of branch circuit When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit. 2. Providing protective earth When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection. 3. Internal air ambient temper
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Table of Contents Manual Structure Purpose of this manual .............................................................................................. 3 Related manuals......................................................................................................... 3 Contents ..................................................................................................................... 3 1. Installation 1-1. Operating Environment ..................................................
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
Manual Structure Purpose of this manual This manual is the installation manual of Switcher Processor Pack MVS8000SF-C and their optional boards and units. This manual is intended for use by trained system and service engineers, and describes the information on installing the MVS8000SF-C. Related manuals The following manuals are prepared for MVS8000SF-C and their optional boards and units. .. ... Operation Manual (Supplied with MVS8000SF-C) This manual describes the application and operation of
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
Section 1 Installation 1-1. Operating Environment m . As the inrush current at turn-on is a maximum 60 A (at Operating guaranteed temperature : +5 dC to +40 dC 100 V)/110 A (at 230 V), the capacity of the AC power Performance guaranteed temperature : +10 dC to +35 dC source must be commensurate with this load. Operating humidity : 10 % to 90 % If the capacity of the AC power is not adequately large, (relative humidity) the AC power source braker will operate or the unit will Storage temperature
ページ10に含まれる内容の要旨
1-3. Installation Space (External dimensions) 1-3. Installation Space (External dimensions) 1-3-1. MVS8000SF-C 482 465 440 375 144.5 115.5 115.5 35 61 370 Unit : mm MVS-8000SF 1-2 7 279.4 37.6 354(8U) 17.5 35 520 339
ページ11に含まれる内容の要旨
1-4. Installing the Options 1-4. Installing the Options Model name Board Structure Plug-in board Connector board The MVS8000SF-C is shipped from the factory with the MKS-8440M DIO-74 board _ necessary option boards (refer to the following table) Frame Memory Board Set MY-102 board _ already installed in accordance with the specified system MKS-8210K1 DI-43 board _ configuration. 1 M/E Upgrade Kit The following options are available for the MVS-8000SF. DO-44 board _ MKS-8440K1 DIO-74 board _ Fram
ページ12に含まれる内容の要旨
1-4. Installing the Options Installation Procedure 4. While the eject levers are opened as shown in the 1. Turn off the main power of the MVS-8000SF and illustration, insert the plug-in board into the board disconnect the AC power cord from the wall outlet. guide rail. 2. Loosen the four screws (with drop-safe) and remove the front panel to the arrow. Screws (with drop-safe) Front panel Screws (with drop-safe) 3. Remove the six screws and remove the plug-in board loose-proof assembly. Eject leve
ページ13に含まれる内容の要旨
1-4. Installing the Options 5. While closing the eject levers in the direction of arrow Name of option Name of board Slot on the front side 1, push in the plug-in board. *1 MKS-8210HD/SD/M DO-41/DO-42/ 3, 8 DO-44 board MIX-45 board 4, 9 KPC-16 board 5, 10 DI-40/DI-41/ 6, 11 DI-43 board MKS-8170HD/SD/M DIF-119/DIF-122/ 7 DIF-141 board MKS-8420M CC-90 board 12 *2 MKS-8160HD/SD/M OUT-23/OUT-24/ 14 , 15 OUT-27 board MKS-8440HD/SD/M DIO-62/DIO-63/ 16 DIO-74 board MY-102 board 17 *1 : Note when instal
ページ14に含まれる内容の要旨
1-4. Installing the Options 1-4-2. Installing the Connector Board 2. Insert the connector board horizontally level and secure it with the two fixing screws. 1. Remove the two screws and remove the blank panel. n To install the connector board into the slot in which the other board is installed already, loosen the two fixing screws and remove the connector board that is installed already. Fixing screw Connector board Fixing screw B3 x 5 Blank panel Name of option Name of board Slot on the rear si
ページ15に含まれる内容の要旨
1-4. Installing the Options 1-4-3. Installing the HK-PSU04 4. Push the portion of the HK-PSU04 marked by the arrow and insert the HK-PSU04 into deep end as far as The HK-PSU04 is used after it is installed in the MVS- it will go. 8000SF. 5. Secure the HK-PSU04 with the two screws removed in n step 3. Before installing the HK-PSU04, be sure to turn off the main power. If the HK-PSU04 is installed while the main power is turned on, it can result in electrical shock or damage to printed circuit boa
ページ16に含まれる内容の要旨
1-4. Installing the Options 1-4-5. Installing the MKS-8420M c Be sure to turn off the POWER switch before starting MKS-8420M consists of the following boards. installation work. . CC-90 board : 1 piece If installation work is started with the POWER switch left . CPU-DK module : 3 pieces on, it may cause electrical shock or damage to printed circuit boards. CC-90 board installation Refer to “1-4-1. Installing the Plug-in Boards”. Removal 1. Remove the OUT-23 board from the MVS-8000SF. CPU-DK modu
ページ17に含まれる内容の要旨
1-5. Rack Mounting 1-5. Rack Mounting 2. Rack Mounting Procedure The MVS-8000SF is mounted in the 19-inch standard rack. This section describes the rack mounting procedure using To mount the MVS-8000SF in the rack, use the specified the RMM-10 rack mount kit. rack mount kit and follow the procedure described below. n Specified rack mount kit : RMM-10 Tighten the screws to the following torque. _2 n Tightening torque : 120 x 10 N.m {12.2 kgf.cm} If other than the specified rack mount kit is used,
ページ18に含まれる内容の要旨
1-5. Rack Mounting 2. Loosen the screws on the rear of the right and left 6. Align the groove of the rack tool at the side of the adapters and adjust the length of the adapter according equipment with the rail, and slide the equipment to the to the depth of the rack. rear. (The illustration below shows the left adapter.) n The rack tools are hooked on the rails as shown below. Adapter Portion of Rack tool Rack tool B4 x 6 the rail B4 x 6 Rail Rail n 7. Fix the rack angle in the rack using the sp
ページ19に含まれる内容の要旨
1-6. Matching Connectors 1-6. Matching Connectors Use the following connectors, cables or equivalents when connecting cables to the unit. Model name Panel indication Connector name Matching connector and cable Name Sony part No. MKS-8110SD/HD/M PRIMARY INPUTS BNC, 75 Z Belden 8281 coaxial _ 1 to 17 cable (SDTV system) MKS-8160SD/HD/M OUTPUTS 1 to 8 or Belden 1694 coaxial cable (HDTV system) MVS-8000SF REF IN BNC, 75 Z Belden 8281 coaxial _ cable REF OUT EXT REMOTE 1 to 4 D-sub 9-pin, Female D-su
ページ20に含まれる内容の要旨
1-7. Input/Output Signals of Connectors 1-7. Input/Output Signals of Connectors Pin No. Signal Name Function 11 GPI OUT 6 General-purpose relay The input/output signals of the connectors at the rear panel (*4) output (B) 12 GPI OUT 8 are as follows. 13 GPI OUT COM Ground for open collector output TERMINAL : RS-232C (D-sub 9-pin, Female) 14 GND Ground to Terminal 15 GPI IN 1 General-purpose input 1 5 16 GPI IN 3 9 6 17 GPI IN 5 _ EXT VIEW _ 18 GPI IN 7 19 GPI OUT 1A General-purpose relay Pin No.
