ページ1に含まれる内容の要旨
PARTNER
Advanced Communications System
1600 DSL Module User Guide
Issue 1
May 2001
ページ2に含まれる内容の要旨
Table of contents 1. Introduction...................................................................11 Organization of this guide ..................................................... 11 2. PARTNER ACS 1600 DSL module basics....................13 Hardware and software requirements ................................... 13 Connectors............................................................................ 13 Console cable.................................................................. 13 Interf
ページ3に含まれる内容の要旨
4. Menu interface...............................................................23 Main Menu ............................................................................ 23 1. Reports Menu.................................................................... 24 C. Display Current Configuration ..................................... 24 N. Display Network Statistics........................................... 26 I. Display Interface Statistics............................................ 26 M. Display
ページ4に含まれる内容の要旨
O. Enable/Disable Spanning Tree by Port ....................... 41 R. Configure Spanning Tree Bridge Priority..................... 41 Q. Configure Spanning Tree Port Priority ........................ 42 H. Configure Spanning Tree Hello Time .......................... 42 S. Configure Spanning Tree Max Age ............................. 42 F. Configure Spanning Tree Forward Delay .................... 42 C. Configure Spanning Tree Path Cost ........................... 42 D. Delete Bridge Forwarding
ページ5に含まれる内容の要旨
Z. Configure Console Baud Rate..................................... 61 V. Configure Console Timeout......................................... 61 R. Hard Reset or Reload ACOS from FLASH.................. 61 D. Set System Defaults.................................................... 61 W. Save System Settings as Defaults ............................. 61 F. File System Menu........................................................ 61 X. File Transfer Menu ...............................................
ページ6に含まれる内容の要旨
C. Display NAT Connection Table ................................... 72 D. Display NAT Connection Details ................................. 72 O. Display NAT Local Server Table................................. 72 X. Delete IP Address from NAT Tables ........................... 72 Y. Delete NAT Local Server Entry ................................... 73 T. Derived Timing.................................................................. 73 1. Enable/Disable Derived Timing.............................
ページ7に含まれる内容の要旨
E. Call Control Settings......................................................... 82 A. Stats Display ............................................................... 82 R. Ring Test..................................................................... 82 S. Display IAD State ........................................................ 83 T. Trace ........................................................................... 83 V. Pick sound heard if insufficient WAN B/W to complete call ................
ページ8に含まれる内容の要旨
Upgrading ACOS .................................................................. 97 Configuring the TFTP Server........................................... 97 Using TFTP...................................................................... 97 Using Telnet..................................................................... 99 Verifying the download .................................................... 99 Support ............................................................................... 100 6
ページ9に含まれる内容の要旨
Configuring the congestion parameters ......................... 123 Configuring the voice path .................................................. 124 Setting the jitter delay .................................................... 124 Setting the SLIC Control Mode ...................................... 125 Configuring Echo Cancellation....................................... 125 7. Router configuration...................................................128 Configuring an IP address...................
ページ10に含まれる内容の要旨
Enabling STP ...................................................................... 148 Enabling STP globally.................................................... 148 Enabling STP by port..................................................... 149 9. NAT configuration.......................................................151 Enabling NAT translation .................................................... 152 Configuring the NAT local server entry ............................... 153 Configuring the NAT
ページ11に含まれる内容の要旨
B. PARTNER ACS 1600 DSL module specifications .....186 C. Connector pinouts ......................................................188 D. USI Cables ...................................................................190 DTE or DCE? ...................................................................... 190 Which Hardware Protocol? ................................................. 190 E. IP Filtering ...................................................................193 Glossary ...................
ページ12に含まれる内容の要旨
1. Introduction The Avaya PARTNER Advanced Communications System(ACS) 1600 DSL module allows you to simultaneously transport both voice and data services over a DSL, without the cost of additional lines. The PARTNER ACS 1600 DSL module supports a variety of network transports, including ATM and Frame Relay, as well as SDSL and phone connections. Supported Interface standards include: DSL-SDSL (Symmetrical Digital Subscriber Line) that supplies voice lines and data connection for the PARTNER ACS
ページ13に含まれる内容の要旨
Chapter 6, “Router configuration”, describes how to configure the PARTNER ACS 1600 DSL module as a router. Chapter 7, “Bridge configuration”, describes how to configure the PARTNER ACS 1600 DSL module as a bridge. Chapter 8, “NAT configuration”, walks you through the steps required to configure the Network Address Translation (NAT). Chapter 9, “DHCP server configuration”, walks you through the steps required to configure the Dynamic Host Configuration Protocol (DHCP) server. Chapter 10, “Menu in
ページ14に含まれる内容の要旨
2. PARTNER ACS 1600 DSL module basics This chapter describes the PARTNER ACS 1600 DSL module hardware and software requirements, as well as the physical IAD. Hardware and software requirements You must use a terminal emulation program, such as HyperTerminal or ProCommPlus, to configure the PARTNER ACS 1600 DSL module. Once you configure an IP address, you can also use Telnet to remotely administer the PARTNER ACS 1600 DSL module. For more information, see the “Getting started” chapter. Connect
ページ15に含まれる内容の要旨
Front View V.35 Console Ethernet DSL Line PARTNER Power LED LAN Avaya, Inc. - 14 - PARTNER ACS 1600 DSL module User Guide
ページ16に含まれる内容の要旨
3. Getting started This chapter walks you through the procedures to connect and log on to the PARTNER ACS 1600 DSL module. It also provides information about the Menu interface, restarting the PARTNER ACS 1600 DSL module, auto log off, exiting the menu interface and verifying an IP address. For more information on the menus, submenus and commands in this chapter, see the “Menu interface” chapter. Connecting You can configure the PARTNER ACS 1600 DSL module while connected to a PARTNER system or
ページ17に含まれる内容の要旨
Using a terminal emulation program To use a terminal emulation program to log on to a PARTNER ACS 1600 DSL module 1. Open the terminal emulation program. 2. Select the name, icon and COM port for the PARTNER ACS 1600 DSL module connection. 3. Type or select the following settings, and then save your changes. Bits per second: 19200 Data bits: 8 Parity: None Stop bits: 1 Flow control: None Emulation: ANSI Font: Terminal For more information, see your terminal emulation program documentation. 4. Pr
ページ18に含まれる内容の要旨
8. Configure Login 9. System Utilities D. Configure DHCP Server N. Configure NAT T. Derived Timing Z. Diagnostics Menu C. Command Line Interface P. VoicePath Configure For more information on the menus, submenus and commands on the Main Menu, see the “Menu interface” chapter. Using a Telnet program You must set an IP address for the Ethernet port before you can use a Telnet program to access the PARTNER ACS 1600 DSL module. Configuring a port IP address To configure a port IP address: 1. On the
ページ19に含まれる内容の要旨
2. Select Configure Port IP Address. The following instructions display on-screen: Available Interfaces : 1. SDSL 2. 10/100BaseT Ethernet 3. Universal Serial 0. (Abort) Selection : Interfaces may or may not display, depending on the IAD in use. 3. Type the number of the port for which you want to configure an IP address. The following message (or one similar) displays: IP interfaces on port 1: ID IPAddr IPMask Priority 0 255.255.255.0 255.255.255.0 NORMAL Enter connection to configure: 4. Type t
ページ20に含まれる内容の要旨
Running the Telnet program To use a Telnet program to log on to a PARTNER ACS 1600 DSL module 1. Open the Telnet program. 2. Type the IP address of the port that you configured in steps 1-6, press CONNECT, and then press any key. The log on message displays. Enter Login ID > 3. Type your User ID, and press ENTER. The following are the default User IDs and passwords: Access Level User ID Password User User TBD Network Administrator NetMan TBD For more information, see the "Administration" chapter
