ページ1に含まれる内容の要旨
NDA-24273
ISSUE 1
STOCK # 152009
®
ISDN Features and Specifications
APRIL, 2000
NEC America, Inc.
ページ2に含まれる内容の要旨
LIABILITY DISCLAIMER NEC America, Inc. reserves the right to change the specifications, functions, or features, at any time, without notice. NEC America, Inc. has prepared this document for use by its employees and customers. The information contained herein is the property of NEC America, Inc. and shall not be reproduced without prior written approval from NEC America, Inc. term NEAX and D are registered trademarks of NEC Corporation. Copyright 2000 NEC America, Inc. PrintedinU.S.A.
ページ3に含まれる内容の要旨
ISSUE No. ISSUE No. PAGE No. PAGE No. 12 345 678 123 456 78 i 1 ii 1 iii 1 iv 1 v 1 vi 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 11 1 12 1 13 1 14 1 15 1 16 1 17 1 18 1 19 1 20 1 ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4 DATE APRIL, 2000 DATE DATE DATE ISSUE 5 ISSUE 6 ISSUE 7 ISSUE 8 DATE DATE DATE DATE 2 NEAX2000 IVS Revision Sheet 1/1 ISDN Features and Specifications NDA-24273
ページ4に含まれる内容の要旨
2 NEAX2000 IVS ISDN Features and Specifications TABLE OF CONTENTS Page BUSINESSFEATURE LIST. . .. .. ....... .. .. ....... .. .. ....... .. .. ....... .. .. ....... .. ii SUPPORTED NETWORK SERVICES (TRUNK PRE-PROVISIONED ONLY) . . . . . . . . . . . ....... .. iii ISDN NETWORK REQUIREMENTS FOR LAYER ONE (1) . . . ....... .. .. ....... .. .. ....... .. iv TABLE OF FEATURES . . . . . .. .. ....... .. .. ....... .. .. ....... .. .. ....... .. .. ....... .. v CALL-BY-CALL SERVICE SELECTION . . . . .
ページ5に含まれる内容の要旨
BUSINESS FEATURE LIST Account code Maintenance Administration Terminal (MAT) Answer Key Fault Messages Attendant Delay Announcement Peg Count Attendant Overflow Night Service Authorization Code Call Rerouting Automated Attendant Day/Night Mode Change - ATTCON Broker’s Call Day/Night Mode Change - Station Call Forwarding Night Connection - Fixed Call Forwarding - All Calls Night Connection - Flexible Call Forwarding - Busy Line Trunk Answer from Any Station (TAS) Call Forwarding - No Answer Route
ページ6に含まれる内容の要旨
SUPPORTED NETWORK SERVICES (TRUNK PRE-PROVISIONED ONLY) AT&T Software Defined Network Global Software Defined Network International 800 Service ® International MEGACOM 2 Also, AT&T’s Alternate Destination Call Redirection fearure is supported by the NEAX2000 IVS . NT Incoming Note -Private -Tie -WATS -800WATS Outgoing Note -DID/DOD 2 Note: Services that do not require NSF can be supported by the NEAX2000 IVS . 2 NEAX2000 IVS ISDN Features and Specifications NDA-24273, Issue 1.0 Page
ページ7に含まれる内容の要旨
ISDN NETWORK REQUIREMENTS FOR LAYER ONE (1) Interface: T1(1.544 M) only Framing: ESF (24 Multiframe) only Line Coding: B8ZS only D Channel Rate: 64K only D Channel: T1 Channel Number 24 (24th channel). Individual B channels cannot be looped back, local or remote. 2 NEAX2000 IVS ISDN Features and Specifications Page iv NDA-24273, Issue 1.0
ページ8に含まれる内容の要旨
TABLE OF FEATURES X = available → = carried over to next level software FEATURE 1900 2000 CALL-BY-CALL SERVICE SELECTION X → CALLED PARTY RECOGNITION SERVICE X → (DIRECT-IN TERMINATION (DIT)) CPN TO NETWORK—PRESENT X → CPN TO TERMINATING USER—DISPLAY X → DID ADDRESSING X → DID AND DOD ADDRESSING X → EVENT BASED CCIS X → ISDN TERMINAL X → ® X → MEGACOM ACCESS/WATS ® X → MEGACOM 800 SERVICE/800 WATS/ULTRA WATS ® → X MULTIQUEST /900 SERVICE SUB-ADDRESS—PRESENT X → TRUNK PROVISIONING SERVICE
ページ9に含まれる内容の要旨
This page is for your notes. 2 NEAX2000 IVS ISDN Features and Specifications Page vi NDA-24273, Issue 1.0
ページ10に含まれる内容の要旨
CALL-BY-CALL SERVICE SELECTION CALL-BY-CALL SERVICE SELECTION General Description Services can be selected on a call-by-call basis to all channels of a single PRI interface according to applications. That is, unlike Trunk Provisioning Service in which services are assigned to specific channels, services may be used on any available channel. Operating Procedure No manual operation is required. Service Conditions 1. The services that can be designated include ACCUNET, MEGACOM, MEGACOM 800, INTERNA
ページ11に含まれる内容の要旨
CALLED PARTY RECOGNITION SERVICE (DIRECT-IN TERMINATION (DIT)) CALLED PARTY RECOGNITION SERVICE (DIRECT-IN TERMINATION (DIT)) General Description This feature provides an incoming Direct-In Termination (DIT) call via an ISDN trunk to be connected to a pre- determined station. This application can be used for a station or modem. Operating Procedure No manual operation is required. Station Application All stations. Service Conditions 1. For incoming calls in a Primary Rate Interface trunk, this se
ページ12に含まれる内容の要旨
CPN TO NETWORK–PRESENT CPN TO NETWORK–PRESENT General Description This feature allows the ISDN network to be informed of the Calling Party Number (CPN) when a call originates from a terminal connected to the System. DIAL "516-555-4210#" PBX For this example, the CPN sent to the network may be 214-555-5000 for every station in the PBX, or each DTI station may present a unique extension number (last (214-555-5000) ISDN four digits) to the ISDN network. 4210 Called Party No. (214-555-5001) 516-555-
ページ13に含まれる内容の要旨
CPN TO TERMINATING USER–DISPLAY CPN TO TERMINATING USER–DISPLAY General Description This feature provides a visual display of the originating station’s number and subaddress information on a Multiline Terminal for incoming ISDN calls. This provides the terminal user with a quick and accurate way to identify the originating station’s number (Calling Number). Operating Procedure No manual operation is required. The originating station number is automatically displayed on the Multiline Terminal. Se
ページ14に含まれる内容の要旨
DID ADDRESSING DID ADDRESSING General Description This feature allows incoming ISDN-PRI calls to terminate to stations, ATTCON, Automated Attendant, etc., based on the Called Party number. Direct Inward Dial trunks will be terminated to preprogrammed destinations without Attendant assistance. Operating Procedure No manual operation is required. Station Application Not applicable. Service Conditions 1. If the network is notified that the destination station for the DID call is busy or a connectio
ページ15に含まれる内容の要旨
DID AND DOD ADDRESSING DID AND DOD ADDRESSING General Description This feature allows the system to use DID and DOD on the same B channels. Trunk Provisioning Service Selection is not required. (B-channels can be used for DID and DOD without separating the trunk routes.) B-channels PRI D-channel Operating Procedure No manual operation is required. Service Conditions 1. Confirm the DID and DOD selection with the customer’s local exchange carrier prior to installation. 2. For more details, refer t
ページ16に含まれる内容の要旨
EVENT BASED CCIS EVENT BASED CCIS General Description This feature allows a PBX customer that does not have a tie line (or when a customer can not use the tie line due to the busy or fault of the line), to use the various CCIS feature by using the ISDN line as a CCIS virtual tie line, 2 2 2 on the 2400 IMX - NEAX2000 IVS connection or the NEAX2000 IVS - NEAX2000 IVS connection. Operating Procedure No manual operation is required. Service Conditions 2 2 1. Event Based CCIS is available between NE
ページ17に含まれる内容の要旨
EVENT BASED CCIS Table 1 CCIS Features Available with Event Based CCIS SERVICE FEATURE AVAILABILITY REMARKS Attendant Camp-On with Tone Indication-CCIS X Attendant Controlled Conference-CCIS X Note 4 Brokerage-Hot-Line-CCIS X Busy Verification-CCIS X Call Back-CCIS X Call Forwarding-All Calls-CCIS X Call Forwarding-Busy Line-CCIS X Call Forwarding-Don’t Answer-CCIS X Call Forwarding-Intercept-CCIS X Call Forwarding-Override-CCIS X Calling Name Display-CCIS X Calling Number Display-CCIS X Call Tr
ページ18に含まれる内容の要旨
EVENT BASED CCIS Table 1 CCIS Features Available with Event Based CCIS SERVICE FEATURE AVAILABILITY REMARKS Message Waiting Lamp Setting-Station-CCIS X Note 3 Miscellaneous Trunk Access-CCIS X Miscellaneous Trunk Restriction-CCIS X Multiple Call Forwarding-All Calls-CCIS X Multiple Call Forwarding-Busy Line-CCIS X Multiple Call Forwarding-Don’t Answer-CCIS X Night Connection Fixed-CCIS X Night Connection Flexible-CCIS X Outgoing Trunk Queuing-CCIS – Paging Access-CCIS X Restriction from Outgoing
ページ19に含まれる内容の要旨
ISDN TERMINAL ISDN TERMINAL General Description This feature provides the system with an ISDN Terminal or Terminal Adapter (TA). ISDN Terminal to ISDN Terminal, ISDN Terminal to ISDN Trunk, ISDN Trunk to ISDN Terminal, ISDN Terminal to Single Line Telephone, ISDN Terminal to Multiline Terminal, and ISDN Terminal to PS connections are available. Operating Procedure No manual operation is required. Service Conditions 1. The ISDN Line Circuit (ILC) card and the ISDN Channel handler (ICH) card are r
ページ20に含まれる内容の要旨
ISDN TERMINAL 6. During communication via the CCIS network, the link reconnection is not available. 7. The conditions about station services are as follows: Station Hunting When a Single Line Telephone/Multiline Terminal or an ISDN Terminal calls a busy Single Line Telephone/Multiline Terminal, another Single Line Telephone/Multiline Terminal in Station Hunting group is called. When a Single Line Telephone/Multiline Terminal or an ISDN Terminal calls a busy ISDN Terminal, another ISDN Terminal
