ページ1に含まれる内容の要旨
User Instructions
Model SS-1002
Single Channel
Intercom Speaker
Station
Model SS-2002
Two Channel
Intercom Speaker
Station
Model SS-2002RM
Two Channel
Rack Mount
Intercom Speaker
Station
®
Audiocom Intercom Systems
9350-7741-000 Rev A, 10/2002
1
ページ2に含まれる内容の要旨
FCC Statement This equipment uses, and can radiate radio frequency energy that may cause interference to radio com- munications if not installed in accordance with this manual. The equipment has been tested and found to comply with the limits of a Class A computing device pursuant to Subpart J, Part 15 of FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area may cause in
ページ3に含まれる内容の要旨
Table of Contents Introduction............................................................................... 4 Description ................................................................................ 4 Features ..................................................................................... 4 Installation................................................................................. 6 Unpacking ..........................................................................................
ページ4に含まれる内容の要旨
Introduction Thank you for purchasing the Audiocom SS-1002/SS-2002/SS-2002RM Intercom Speaker Station. We hope the many design features of this product will satisfy your intercommunication requirements for many years to come. To get the most out of your new intercom station, please take a few moments to look through this booklet before using the Intercom Speaker Station for the first time. Description The Intercom Speaker Stations may be used with a headset, or with the built-in speaker and the
ページ5に含まれる内容の要旨
Figure 1 - SS-1002 / SS-2002 features. Figure 2 - SS-2002RM features. 5
ページ6に含まれる内容の要旨
Installation Unpacking Each SS-1002 / SS-2002 / SS-2002RM is supplied with the following items. Contact the shipper or your Audiocom dealer immediately if anything is damaged or missing. Be sure to fill out and return the product registration card to Telex to properly register your intercom station. For SS-1002 / SS-2002 units: Qy QQn Qy u u u ua a a an n n nt t t ti i i it t t ty y DDn Dn De e e es s s sc c c cr r r ri i i ip p p pt t t ti i i io o o on Quantity Description 1n SS1002 or SS2002
ページ7に含まれる内容の要旨
Mic Kill Receive Audiocom master stations, such as the US-2002A, can transmit an inaudible signal to turn off the microphones in all remote intercom stations on an intercom channel. This is useful when a remote intercom station has been left unattended with the microphone on. The procedure to send a mic kill signal from a master station is a two-step process, so that it is very unlikely that microphones will ever be turned off by accident. However, you may wish to disable the mic kill receive fe
ページ8に含まれる内容の要旨
Headset Connector Notes If you are using a monaural, dynamic-mic headset, or a monaural, telephone-style, dynamic-mic handset, or a handheld dynamic microphone, plug it into the Headset connector. You can also use this connector with monaural headphones for listening when you are using either the built in panel microphone, or the optional gooseneck microphone for talk back. Panel Mic Connector Notes As an alternative to a headset or telephone-style handset, you can use either the built-in panel
ページ9に含まれる内容の要旨
intercom stations may be reduced. Generally, if intercom stations are within a few hundred feet from the system power supply, phantom power will be sufficient. Also note that increasing the number of stations will reduce the overall operating distance. Phantom power is generally the only method that will be used to connect the “S” box, “P” box, and RM versions. Figure 5 illustrates a phantom powered intercom system. Note that the distance over which power can be delivered is less than the distan
ページ10に含まれる内容の要旨
All Locally Powered Intercom Stations (Dry Lines) If intercom stations are widely distributed, you can dispense with a system power supply (PS2001L, SPS-2001, etc.) and use local power for each station. When no power is delivered on the intercom channels, this is known as dry-line operation. Since a system power supply is not used, a line termination must be inserted in each intercom channel for proper operation. Again, note that only the “U” box has provisions for local power. The 3-pin connect
ページ11に含まれる内容の要旨
Figure 9 - Audiocom mode connections for an SS1002 Intercom Station in a “U” box. Note: for Clear-Com connection, use the Unbalanced Mode Intercom Channel pin-out information listed in the Specifications section. 11
ページ12に含まれる内容の要旨
Figure 10 - Audiocom mode connections for an SS2002 Intercom Station in a “U” box. Note: for Clear-Com connection, use the Unbalanced Mode Intercom Channel pin-out information listed in the Specifications section. 12
ページ13に含まれる内容の要旨
Figure 11 - Audiocom cable wiring diagrams. 13
ページ14に含まれる内容の要旨
Power-Up Make sure any local power supplies are plugged in, then turn on the power switches of any phantom power supplies (PS- 2001L, SPS-2001, etc.) Sidetone Adjustment The SS-1002, SS-2002, and SS-2002RM use full-duplex audio (the same as conventional telephone lines) in which the talk and listen audio are sent and received on the same wires. Thus, when you talk, you also here your own voice back as with a telephone. If you are using the built-in speaker for listening and a either a panel micr
ページ15に含まれる内容の要旨
Operation Channel Select (SS-2002 & SS-2002RM Only) Tap the Ch Select key to select channel 1 or 2. The key is green when channel 1 is selected and red when channel two is selected. Headset/Headphone/Speaker/Microphone Selection • To use a headset or telephone style handset, set the Speaker and Panel Mic keys to off. • To use headphones with the built-in panel microphone, set the Speaker key to off, set the Panel Mic Key to on, and make sure that a gooseneck microphone is not inserted in the pan
ページ16に含まれる内容の要旨
Specifications General Power Requirements: Phantom Power: +24 VDC nominal, 175 mA Local Power: +12 to +15 VDC, 250 mA Dimensions: See dimension drawings. Environmental Requirements: Storage: -20°C to 80°C; 0% to 95% RH, non-condensing Operating: -15°C to 60°C; 0% to 95% RH, non-condensing Dynamic-mic Headset/Handset Microphone: 50 to 200 ohms, dynamic (balanced or unbalanced) Headphones: 150 to 600 ohms, monaural Connector Type: XLR-4M Pin 1 - Microphone Low Pin 2 - Microhpne High Pin 3 - Headph
ページ17に含まれる内容の要旨
Call Signaling: Dimensions Pin 1 - Common Pin 2 - Local power (+12 to +15 VDC) If needed Pin 3 - Power +30 VDC Pin 4 - Intercom channel 1 audio and DC call signaling Pin 5 - Power +30 VDC Pin 6 - Intercom channel 2 audio and DC call signaling Speaker Output Power 4W max @ 8 ohms 17
ページ18に含まれる内容の要旨
TRADEMARKS ® Audiocom is a registered trademark of Telex Communications. Names of other products mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies. WARRANTY INFORMATION Products are warranted by Telex Communications, Inc. to be free from defects in materials and workmanship for a period of one year from the date of sale. The sole obligation of Telex during the warranty period is to provide, without charge,
