ページ1に含まれる内容の要旨
54-2106-01A.qxd 12/12/2003 11:38 AM Page 1
Analog Door Phone
Model LUADS
Installation and Use Manual
• Telephone line powered
• Two-way, hands-free communication
• Vandal-resistant brushed stainless steel faceplate with
mounting gasket and heavy-duty call button
• Adjustable microphone and speaker volume
• Adjustable call timer duration
• Defeatable call timer
• Responds to forward disconnect
• Selectable Auto Answer feature allows remote monitoring
Issue 1, December 2003
© 2003 Bogen Communi
ページ2に含まれる内容の要旨
54-2106-01A.qxd 12/12/2003 11:38 AM Page 2 Notice Every effort was made to ensure that the information in this manual was complete and accurate at the time of printing. However, information is subject to change. Important Safety Information Always follow these basic safety precautions when installing and using the system: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. DO NOT block or cover the ventilation slots and openings. 4. Never
ページ3に含まれる内容の要旨
54-2106-01A.qxd 12/12/2003 11:38 AM Page 3 Package Contents •(1) LUADS •(1) Dual gang electrical box • (4) Panel screws •(1) Hex wrench Features Auto Answer The LUADS can be programmed to automatically answer an incoming call.This feature can be enabled or disabled using a jumper. Timer Duration The LUADS can be programmed to automatically disconnect a call after a preset amount of time has elapsed.The timer can be set between 15 seconds and 2 minutes. When the call is initiated by the unit,
ページ4に含まれる内容の要旨
54-2106-01A.qxd 12/12/2003 11:38 AM Page 4 Programming 4 TEL Line Connector - Analog Speaker Volume - The Speaker station line connection (Tip and Ring) Volume POT can be adjusted to is made via an RJ11 connector that is increase or decrease the speaker pre-wired to a 2-position pluggable volume to the desired level. terminal block. Not polarity sensitive. Mic Level - A Mic Level POT is provided on the Auto Answer Feature - The Auto LUADS for increasing or Answer feature can be enabled or dec
ページ5に含まれる内容の要旨
54-2106-01A.qxd 12/12/2003 11:38 AM Page 5 Wiring Phone Connection To connect the LUADS to a phone system, simply connect the analog station line to the RJ11, which is already wired to a pluggable terminal block that is preassembled to the cir- cuit board.The connections to the terminal block are not polarity sensitive. Surge Protection To increase surge protection, connect a protective Earth Ground to the spare lug provided.The location of the spare lug is shown below. 5
ページ6に含まれる内容の要旨
54-2106-01A.qxd 12/12/2003 11:38 AM Page 6 Installation The LUADS comes with a standard dual gang electrical box. Make all electrical connections prior to installing the LUADS into the electrical box. Surface Mounting the LUADS (Indoor/Outdoor) 1. Mount electrical box. 2. Make electrical connections (see Wiring) and attach the faceplate to the electrical box using the four hex drive screws (tool provided). 6
ページ7に含まれる内容の要旨
54-2106-01A.qxd 12/12/2003 11:38 AM Page 7 Specifications Power: Telephone line powered (18V DC / 20 mA minimum) Timer Duration: 15 seconds to 2 minutes Loop Current Loss Disconnect: 300 ms minimum Ring Voltage: 40V AC RMS minimum REN: 0.7A Connections: RJ11 pre-wired to a 2-position pluggable terminal block Earth Ground lug 1 Dimensions: 5" W x 5" H x 2 /4" D (fully assembled) 5 5 4 /8" W x 4 /8" H x 2" D (aluminum box) Product Weight: 4 lb. 7
