ページ1に含まれる内容の要旨
VD03
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS ® Thank you for purchasing the Heritage™ Natural Spectrum Deluxe Desk Lamp. Please read the following safety information before using. To reduce the risk of fi re, electrical shock, or injury to persons: • Do NOT dismantle. • Do NOT alter power cord. • Turn off/unplug and allow to cool before replacing bulb or cleaning. • For indoor use only. • The lamp is an electrical device. DO NOT USE NEAR WATER GENERAL PRECAUTIONS • Before plugging in
ページ3に含まれる内容の要旨
GETTING STARTED Main Parts & Controls A. Lamp Head G. Vertical Shaft B. Switch H. Lamp Base C. Lamp Head Swivel Knob I. Power Cord D. Lamp Arm J. Power Supply (Ballast) ® E. Center Swivel Knob K. Optix Glare Control Filter F. Counter Weight Arm L. Bulb C A D E F L Close-up of Lamp Head G B H I J A 4
ページ4に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS Please Read Operating Instructions Carefully Before Using the Heritage™ Desk Lamp: 1. Set lamp base on the desk and insert the counter weight arm (F) onto the center swivel (E) and screw clockwise to tighten. (Fig.1) 2. To lift lamp head, loosen swivel knob (C), adjust head to desired angle. Tighten swivel knob. ® 3. Attaching the Optix glare control fi lter: • Remove glare control fi lter from protective plastic bag. Take care to hold fi lter by the edges only. • Insert
ページ5に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS cont. 4. Attach the ballast to the power cord. Use care to align the 4-pin plug properly. DO NOT FORCE – the 4-pin plug was designed to fi t in only one orientation. (Fig. 3) Fig. 3 5. Plug ballast into a standard 120V 50/60Hz outlet. Turn lamp on. The green LED indicator on center of the ballast should be illuminated. (Fig. 4) If the LED indicator does not illuminate, please refer to the troubleshooting section of this manual. (See page 9) 6. If bulb does not illum
ページ6に含まれる内容の要旨
ADJUSTING THE HERITAGE DESK LAMP The Heritage™ Desk Lamp D adjusts several ways: E 1. To adjust lamp height – hold lamp arm with one hand, loosen center swivel knob (E). Raise or lower lamp arm (D) to desired height. Tighten knob. (Fig. 5) Fig.5 Swivel Knob 2. To adjust lamp head angle up or down – loosen swivel knob counterclockwise, place head at desired angle, tighten swivel knob to secure. (Fig. 6) Fig. 6 3. To tilt lamp head toward you or away from you – simply move head to desir
ページ7に含まれる内容の要旨
BULB REPLACEMENT INSTRUCTIONS Removal 1. Unplug lamp from power source. ® 2. To access the bulb, remove Optix glare control fi lter by depressing the thumb tab and lifting it out. 3. Firmly hold bulb base (B) and pull bulb (C) from the socket (A) in an outward motion. (Fig. 8) Installation 1. Unplug lamp from power source. 2. Firmly hold base (B) and push bulb (C) into the socket (A). 3. Be sure bulb is fi rmly seated in the socket (see below) and snapped into the metal bulb clip (D). (Fig
ページ8に含まれる内容の要旨
TROUBLESHOOTING ® Your Verilux desk lamp uses advanced micro-electronics to power the revolutionary Trucolite™ bulb. These electronics are housed in a specially designed ballast located at the power plug. The LED indicator light on the ballast allows you to troubleshoot any problems with the ® lamp’s function. When replacing your Verilux ballast, take care to plug in the power cord properly. The 4-pin plug was designed to fi t in only one orientation (See Assembly Instructions on page 5). ®
ページ9に含まれる内容の要旨
CARE & CLEANING Your desk lamp is made from high quality materials that will last for many years with minimum care. You may want to periodically clean the lamp, using a mild non-abrasive cleaner and soft cloth. When cleaning, make sure you have turned off and unplugged the unit, and allowed suffi cient time for the unit to cool. All liquid should be properly wiped away and dried prior to restoring power. DO NOT USE SOLVENTS OR CLEANERS CONTAINING ABRASIVES, OR AMMONIA BASED CLEANERS Note: D
ページ10に含まれる内容の要旨
Please visit our web site at: www.Verilux.com 340 Mad River Park, Waitsfi eld, VT 05673 1-888-544-4865 Printed in China for Verilux, Inc. VD09-MAN-Rev3 © Copyright 2008 Verilux, Inc. All rights reserved.
