ページ1に含まれる内容の要旨
CWST1
ページ2に含まれる内容の要旨
GENERAL PRECAUTIONS • Do NOT dismantle. • Do NOT place near fl ammable or combustible items. • Do NOT alter power cord. • Unplug from electrical outlet during lightning storms or when unused for long periods of time. • Unplug from electrical outlet before cleaning or changing bulbs. • For indoor use only. Main Parts & Controls A. Lens Cover B. On/Off Switch C. Wall Mount Bracket D. Carrying Handle E. Built-in Stand F. Power Cord 2
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS ® ® Thank you for purchasing the Verilux ClearWave Deluxe Phototherapy Skincare System. Please read the following safety information before using. IMPORTANT: ® • Verilux does not make any • The light bulbs may become medical claims. This product is loose during transit. To reinstall not intended to treat or prevent the light bulbs, see the bulb any illness. replacement instructions. ® ® • It is recommended that you • The Verilux ClearWave is an consult a medic
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS THIS PRODUCT MUST BE GROUNDED. This product is equipped with a cord having an equipment–grounding conductor and a grounding plug. The plug must be plugged into anappropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DANGER Improper connection of the equipment–grounding conductor can result in a risk of electric shock. Check with a qualifi ed electrician or serviceman if you are in doubt as to whether the pr
ページ5に含まれる内容の要旨
INSTRUCTIONS FOR USE ® To use the ClearWave Deluxe Phototherapy Skincare System: 1. Plug into properly grounded 5. Turn your face occasionally to outlet. ensure overall exposure. 2. Turn the unit on using the on/off 6. Based on research, a 15 minute switch. Allow a few minutes at session daily for 8–12 weeks the start of each session for should produce the desired bulbs to achieve full illumination. results. ® 3. Gently wash the affected parts 7. While using ClearWave , of the skin with a n
ページ6に含まれる内容の要旨
INSTRUCTIONS FOR USE ® Hanging the ClearWave Place the screw included into the wall leaving approximately 3mm between the screw head and the wall. Be sure to use an the included anchor if mounting into sheet rock or other soft material. Insert the screw head into the hole located in the upper part of unit. (Figure 2). Figure 2 ® Standing the ClearWave on a Table Top Unfold the stand on back of lamp ® (Figure 3) and place the ClearWave on a stable, fl at surface. Figure 3 Transporting th
ページ7に含まれる内容の要旨
BULB REPLACEMENT INSTRUCTIONS Step 1: Opening the Lens Cover ® Place the ClearWave on its back on a large fl at surface. Press down gently on the center of the lens cover. (See Figure 5). This releases the locking tabs located under the grey handles. Open the lens cover by grasping the grey handles with your hands. Remove the lens and gently place it next to the unit with the logo face up. Step 2: Opening the Bulb Clips Locate the clear plastic clips across each fl uorescent tube (F
ページ8に含まれる内容の要旨
BULB REPLACEMENT INSTRUCTIONS Step 3: Removing Bulbs Gently lift the fl uorescent tube up and out of the clip holder. Grasp the tube by the white plastic base ® with the Verilux logo and remove the tube from the socket by pulling the tube towards the black cushion pads. (See Figure 8). Repeat removal of the second bulb. Step 4: Installing New Bulbs ® Ensure the ClearWave is on its back on a large fl at surface. Hold the fl uorescent tubes by the white plastic base, not the glass. Ensure
ページ9に含まれる内容の要旨
BULB REPLACEMENT INSTRUCTIONS Step 5: Closing the Bulb Clips Ensure the plastic bulb clips are centered on the white protective bands. Gently push on the upper portion of the fl uorescent tube until it slides snuggly into the clear plastic clip. Close the clip over the tube. The clip will click when fastened. Repeat on other side. (Figure 9). Step 6: Replacing the Lens Cover Align the lens cover over the open face of the unit with the ® ClearWave logo at the bottom of the lamp. Place
ページ10に含まれる内容の要旨
CARE & CLEANING ® Your ClearWave Deluxe Phototherapy Skincare System is made from high quality materials that will last for many years with minimum care. You may want to periodically clean the inside of the lens and outside parts, using a mild non-abrasive cleaner and soft cloth. When cleaning, make sure you have turned off and unplugged the unit, and allowed suffi cient time for the unit to cool. DO NOT USE SOLVENTS OR CLEANERS CONTAINING ABRASIVES, OR AMMONIA BASED CLEANERS Cleaning the le
