ページ1に含まれる内容の要旨
User’s Manual
HU-318
skylinkhome.com
ページ2に含まれる内容の要旨
CONTENTS INTRODUCTION ......................................................................... 3 SETTING UP THE INTERNET HUB ........................................... 4 PROGRAMMING THE INTERNET HUB .................................... 5-25 Assign Zones and Lights .............................................................................. 7-11 All On/Off ...................................................................................................... 12 Device .........................
ページ3に含まれる内容の要旨
INTRODUCTION SkylinkHome™ Internet Hub allows you to remotely control various devices from a computer, a Smartphone or tablet. With the wireless camera, you may visually see your command occur, turning on a light or opening a door. The following items are included in this package: • One Internet Hub • One Power adapter • One Network cable • User ’ s Manual CD } • Setup Guide INTRODUCTION 3
ページ4に含まれる内容の要旨
SETTING UP THE INTERNET HUB Before installing the Internet Hub, ensure your system/network meets the following requirements. You must have: • An Ethernet RJ-45 port from your existing Wireless router . • A computer installed with an Internet Browser . Follow the steps below to setup your Internet Hub. Make sure you follow each step carefully to ensure that the Internet Hub operates correctly. 1) Insert 4 AAA batteries into the Internet Hub (with the correct polarity as shown). The
ページ5に含まれる内容の要旨
PROGRAMMING THE INTERNET HUB The Internet Hub includes a web graphics user interface (web GUI) which allows you to configure the Internet Hub using your web browser on your computer. After you have connected the Internet Hub to your Wireless router and have applied power to the Internet Hub, write down the IP address shown on the LCD display of the Internet Hub, such as 192.168.001.199:8081. Yours may be different from this. Launch your web browser such as Internet Explorer , Goog
ページ6に含まれる内容の要旨
PROGRAMMING THE INTERNET HUB By default, the Internet Hub is set to DHCP Client, which automatically obtains IP addresses from your router . However , in some instances you may want to assign static IP addresses to the Internet Hub to ensure convenient accessibility . T o assign static IP , Go to [Settings] and then [Network Settings]. 1. The [DDNS Status] should show “Ok”. W rite down the DDNS name: “nh007.my .skyhm.net” in this example (yours will be dif ferent) and Htt
ページ7に含まれる内容の要旨
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB To setup the Internet Hub to control SkylinkHome™ Wireless Modules, follow the steps below: 1. Assign different zones such as Kitchen, Bedroom, Family Room, Hallway etc. 2. Assign different devices in each zone, such as island lights, ceiling lights, pot lights, floor lamp etc. 3. Learn the assigned light to the Wireless Module Assign Zones and Lights 1. Click the Zone icon or [Zone] in the toolbar . 2. Click the [Settings] i
ページ8に含まれる内容の要旨
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB 4. Click [Zone] on the top of the toolbar . Select the zone, e.g. [Kitchen] to assign dif ferent devices to this zone. 5. Click the [Settings] icon in the ‘Kitchen Devices Control Page’, and then assign different devices in this zone. 6. Enter the name of the device (e.g. Island Lights). Select the type of module controlled (On/Of f or T oggle, Dim or Non-Dim) and then click [ADD]. ASSIGN ZONES AND LIGHTS PROGRA
ページ9に含まれる内容の要旨
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB 7. After you have assigned a name for each light or device, you may now learn the light to the Wireless Module. Refer to the User’s Instructions of that specific receiver to put the unit into ‘Learning’ mode, then press the [Learn] button on the Internet Hub interface. The Signal LED will flash, then turn of f on the Internet Hub indicating the ‘Learn’ code has been sent. 8. This light is now programmed to the W
ページ10に含まれる内容の要旨
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB 10. Each light has 4 control buttons: On / Of f / Bright / Dim • Press the [ON] button to turn on that light. • Press the [OFF] button to turn of f that light. • Press the [Bright] button to increase the brightness of that light. • Press the [Dim] button to decrease the brightness of that light. Note: T o change the brightness, make sure the Wireless Module and the load (i.e. the light bulb) are dimmable. 11. You can setup a ca
ページ11に含まれる内容の要旨
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB 13. T o operate the zones, go to [Zone]. Each zone has 4 control buttons: On/Of f/ Bright /Dim. • Press the [ON] button to turn on all the lights in that zone. • Press the [OFF] button to turn of f all the lights in that zone. • Press the [Bright] button to increase the brightness of all the lights in that zone. • Press the[Dim] button to decrease the brightness of all the lights in that zone. Note: To change the brightn
ページ12に含まれる内容の要旨
ALL ON/OFF PROGRAMMING THE INTERNET HUB 1.T o program the all control go to the Home page and click [All]. You will see the following screen: 2. Set your device into learning mode and press the [Learn] button on this screen 3. Repeat “step 2” for every device you want to control with the [All on/of f] button. ALL ON/OFF PROGRAMMING THE INTERNET HUB 12
ページ13に含まれる内容の要旨
DEVICE PROGRAMMING THE INTERNET HUB The ‘Device’ shows you all of the lights which you have programmed. You can control every light/device individually from this page. DEVICE PROGRAMMING THE INTERNET HUB 13
ページ14に含まれる内容の要旨
SCENE PROGRAMMING THE INTERNET HUB Scene control can provide a specific brightness for multiple lights with the press of a button. Common scenes are the morning scene, the evening scene, the movie scene, etc. T o setup a scene, click the [Settings] icon on the Scene control page. 1. Enter the Scene name (e.g. Morning), then click [ADD]. Repeat this step for all the scenes that you plan to assign. 2. T o specify an atmosphere for the scene, go to the [Scene Control] page and
ページ15に含まれる内容の要旨
SCENE PROGRAMMING THE INTERNET HUB 4. After setting the Zone, Light and Brightness, you now have to program this scene setting to the Wireless Module. Refer to the User’s Instructions of the Wireless Module to put the unit into learning mode. Once the Wireless Module is in learning mode, press the [LEARN] button on this screen to program this scene setting to the Island Light module. Y ou may continue to add more lights to this scene. Ensure each light you added to this scene has been
ページ16に含まれる内容の要旨
TIMER PROGRAMMING THE INTERNET HUB You may program up to 10 different timers to the Internet Hub. It will send a signal to control the desired devices at a pre-set time. You may control the following: • T urn a specific light on/of f • T urn a specific zone on/of f • T urn a specific scene on/of f • T urn all lights on/of f You need to set the time and the day of the week for when you want this action to take place. To assign a timer: 1. Click the [T imer] icon. Y ou will
ページ17に含まれる内容の要旨
TIMER PROGRAMMING THE INTERNET HUB 3. Select the timer no., name, zone/scene/all light, time, day of the week and whether on or of f, then press the [SET] button. Once it is entered, the timer setting will show up on the screen. 4. T o enable the timer , go to the T imer page. Click on the clock next to the T imer you want to activate. When there is no red bar across the clock, the timer is enabled. TIMER PROGRAMMING THE INTERNET HUB 17
ページ18に含まれる内容の要旨
TC REMOTE PROGRAMMING THE INTERNET HUB This function allows the user to control all devices with the same interface as the SkylinkHome™ TC Remote Transmitter. Users that are familiar with the TC Remote T ransmitter will find this interface very user friendly . This layout is the same as SkylinkHome™ Model TC-318-14. The buttons on the TC Remote Transmitter can be treated as a standalone control which is not related to any zone or devices assigned to the Internet Hub. TC REMOTE PROGRAMMING THE
ページ19に含まれる内容の要旨
TC REMOTE PROGRAMMING THE INTERNET HUB Program TC to Wireless Modules 1. Refer to the User’s Instructions for the Wireless Module you have, in order to put the unit into ‘Learning’ mode. 2. Click the [Learn] box on the TC Remote page, then click the number button you want to control the Wireless Module with.. : 3. The Wireless Module should respond indicating this TC Remote button is now programmed. Follow the same learning instructions for the Zone command and All
ページ20に含まれる内容の要旨
TC REMOTE PROGRAMMING THE INTERNET HUB Operation Toggle Operation Press buttons 1 -10 to turn on or of f that specific load/module (toggle mode). Pressing the button when the load is of f will turn on the load , and vice versa. Designated On/Off If you want to turn on a light upstairs while you are downstairs and do not know whether that light is already on, you may use the designated on/off buttons. 1. Choose the ON box above the TC Remote 2. Press the number button 3. This will
