ページ1に含まれる内容の要旨
Installation Manual
Setting Plate for Wall Hanging
Model POA-CH-EX06
Contents
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
List of Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Install the wall plate to the wall . .
ページ2に含まれる内容の要旨
Safety Instructions ■ Explanation of Symbols The warning marks shown below are used in this manual to prevent personal injury or property dam- age. Make sure you understand these warnings when reading this installation manual. This symbol indicates information that, if ignored, could possibly result in personal injury or even WARNING death due to incorrect handling. This symbol indicates information that, if ignored, could possibly result in personal injury or physi- CAUTION cal damage due to
ページ3に含まれる内容の要旨
Safety Instructions The installation work should be performed by at least two qualifi ed service personnel. If you need to loosen any screws during installation, be careful not to drop the setting plate. If mounting the projector on a wall with the setting plate, the wall must have enough strength to hold the projector and setting plate. Confi rm the weight of the projector and the setting plate before installation, and check the strength of the wall. If the wall is not strong enough, reinfor
ページ4に含まれる内容の要旨
List of Accessories q r e w tiyo u !0 !2 !1 Wall plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 M5 x 10 mm hexagon socket head cap bolt q i (for securing cover plates) . . . . . . . . . . . . . . . 2 Setting plate . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 w Strap for binding cables . . . . . . . . . . . . . . . . . 2 o Cover plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 e Drop-prevention wire . . . . . . . . . . . . . . . . . . . . 1 !0
ページ5に含まれる内容の要旨
Installation Procedure Install the wall plate to the wall Determine the position of the wall plate using the template sheet. 1 ¡ From the projection distance table (page 10) and dimensions (page 11), confi rm the screen size and the distance between the projection surface and wall plate. ¡ The wall plate and the projection surface have different vertical center lines. Align the CTR line (printed on the template sheet) with the center line of the projection surface as shown in the illustration.
ページ6に含まれる内容の要旨
Installation Procedure Attach the setting plate to the wall plate Hang the setting plate hook onto the wall plate slits. 1 Wall plate Setting plate Tighten the four M8 x 20 mm hexagon socket head cap bolts supplied 2 with the setting plate. (Secure temporarily so that the adjustment men- tioned on page 7 can be carried out.) Bolts Bolts Attach the left and right cover plates to the setting plate using the two 3 M5 x 10 mm hexagon socket head cap bolts included. (Secure temporar- ily so that th
ページ7に含まれる内容の要旨
Installation Procedure Securing the projector to the setting plate Screws Attach the adjustment unit to the 1 projector using the included 5 Adjustment unit screws (M4 x 18). Projector Remove the two bolts (for drop-prevention) 2 from the setting plate. Loosen the four bolts located on the top of the adjustment unit and set the projector with the adjust- ment unit onto the setting plate. Setting plate Bolts Loosen bolts Projector with the adjustment unit Tighten the four bolts which were lo
ページ8に含まれる内容の要旨
Installation Procedure Adjustment Adjust the forward/backward slide 1 (Adjustable range: 0 - 180 mm) ¡ Loosen the four bolts on the top of the setting plate using a hexagon wrench (3 mm) and adjust the slider of setting plate. After the adjustment, Bolts tighten the four bolts which were loosened. 0 - 7.09 inches (0 - 180 mm) Adjust the vertical slide (Adjustable range: +4° - –2°) 2 ¡ Remove the left and right cover plates. ¡ Loosen the four bolts located inside the setting plate using a h
ページ9に含まれる内容の要旨
Installation Procedure Adjust the vertical tilt (Adjustable range: +5° - –5°) 4 ¡ Loosen the screw q located on the left side of the setting plate using the hexagon wrench (3 mm). ¡ Turn the adjustment knob located on the left top side of the setting plate to adjust the vertical tilt. w ¡ Tighten the screw which was loosened using the hexagon wrench (3 mm). q Adjustment knob w 5° 5° Screw q * “B” marks appear on the setting plate to indicate the locations of the screws and adjustment knob.
ページ10に含まれる内容の要旨
Attach the drop-prevention wire to the projector To prevent the projector from falling down, use the included drop-prevention wire to connect the projector and the setting plate. Pass the included drop-prevention wire through the drop-prevention 1 wire installation bar of the projector as shown in the illustration. Drop-prevention wire Drop-prevention wire installation bar Pass the wire through the holes of the setting plate as shown in the il- 2 lustration. Secure the end of the wire at the b
ページ11に含まれる内容の要旨
Projection Distance Table A B 6.85 inch (174 mm) 1.06 inch (27 mm) C D E Projection H surface ●SANYO PDG-DWL2500 Unit: inch (cm) Display Size ABCD E H 110" (16 : 10) 21.45" (54.5) 17.91" (45.5) 6.25" (15.9) 12.79" (32.5) 5.78" (14.7) 58.30" (148.1) 100" (16 : 10) 19.68" (50.0) 16.14" (41.0) 4.48" (11.4) 12.00" (30.5) 5" (12.7) 52.99" (134.6) 97.5" (16 : 10)* 19.21" (48.8) 15.66" (39.8) 4.01" (10.2) 11.81" (30.0) 4.80" (12.2) 51.69" (131.3) 96" (16 : 10) 18.97" (48.2) 15.43" (39.2) 3.77" (9.6) 1
ページ12に含まれる内容の要旨
Dimensions Unit: inch (mm) 18.23 (463) 13.51 (321) 1.06 (27) 6.45 (164) Center line of the projection surface 11 15.83 (402) 15.16 (385) 14.88 (378) 6.85 (174) 15.16 (385) 6.69 (170) 22.24 (565) max.
