ページ1に含まれる内容の要旨
ENGLISH
WorkFit-D
< 65 lbs. (29.5 kg)
Max weight 65 lbs – 29.5 kg
CAUTION: DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR PROP-
ERTY DAMAGE MAY OCCUR!
Reduce.Reuse.Recycle
888-24-205-G-03 rev. E • 12/12
1 of 14
ページ2に含まれる内容の要旨
Symbol Signal Word Level of Hazard Hazard Symbols Review These symbols alert users of a safety condition that A NOTE indicates important information that helps you demands attention. All users should be able to NOTE make better use of this product. recognize and understand the signifi cance of the fol- lowing Safety Hazards if encountered on the product A CAUTION indicates either potential damage to CAUTION hardware or loss of data and tells you how to avoid the or within the documentation.
ページ3に含まれる内容の要旨
ENGLISH WARNING! Stop screws are pre-installed in this product to secure it in the compressed position during shipping and installation. DO NOT REMOVE THESE SCREWS UNTIL INSTRUCTED TO DO SO IN THESE INSTRUCTIONS. Make sure these screws are in place before starting installation. Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury. If any of the 4 phillips head stop screws are not installed in these locations,
ページ4に含まれる内容の要旨
Components 1x 1x 1x Sync Rod 2x Crossbars 1x 2x 17x # 12-14 Wood Screw M5 x 6 mm 16x 3x M2.9 x 8 mm 3x Tools Needed 14mm 1/4” 888-24-205-G-03 rev. E • 12/12 4 of 14 ENGLISH
ページ5に含まれる内容の要旨
ENGLISH Front Edge of Worksurface Set-up Steps Place the worksurface on a clean fl oor with the top side facing down. 1 Carefully position the leg with the hand brake on the right end of the worksurface. Place the other leg on the left end. Rear Edge of Worksurface NOTE: The brake cable is attached to both legs. Take care when re- moving the legs from the packaging to avoid damaging or pulling the brake cable from the legs. Set the right leg (with hand brake) upright on the Front =2 screw
ページ6に含まれる内容の要旨
WARNING Keep Brake Cables Away from Set-up Steps Sync Rod and Crossbars During Installation! Failure to keep the brake cables away from sync rod and crossbars may restrict lift motion and may cause equipment damage Set the left leg (without or personal injury! Refer to instruction manual for more information. hand brake) upright on the 4 worksurface. Attach the left end of the sync rod to the left leg. Make sure the brake cables don’t loop around the sync rod. See Warning, right. Pa
ページ7に含まれる内容の要旨
ENGLISH Set-up Steps 3x 3x Capture the brake cable in the cable clip as M2.9 x 8 mm 8 illustrated, then use a Phillips screwdriver to attach the cable clips to bottom of work surface with the provided M2.9 x 8 mm screws. Using the 2 provided cable ties, attach brake cable 9 to the legs leaving as much slack in cable as possible between the cable tie and the leg to allow desk top to 2x raise up unrestricted. There should be equal lengths of cable on each side. NOTE: Leave as much slack
ページ8に含まれる内容の要旨
Set-up Steps Set the desk upright onto its legs. 10 CAUTION! LIFT HAZARD! Two persons are required for this step. Failure to follow this warning may result in equipment damage and or personal injury. Adjust the riser on each leg and check with a level to 11 make sure the work surface is even. Spin Left to Raise. Spin Right to Lower. 888-24-205-G-03 rev. E • 12/12 8 of 14 ENGLISH
ページ9に含まれる内容の要旨
ENGLISH Set-up Steps Remove the 4 brake stop screws before installing equipment. 12 Remove the 2 stop screws from the legs then the 2 stop screws from the brake to allow the worksurface to raise and lower. 1 IMPORTANT! Save these stop screws and instructions. Install stop screws when shipping or storing this product. Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury. 2 After you remove the 4 brake stop scr
ページ10に含まれる内容の要旨
Set-up Steps Install all equipment. 13 CAUTION! Make sure you leave 20” (508mm) of slack in all equipment cables to allow the worksurface to raise up it’s full 20” (508mm). Failure to allow enough slack in equipment cables may cause cables to get pulled, equipment to fall off desk and may result in product damage and or personal injury. Adjustment Step 14 IMPORTANT! This product will need tension adjustments once installation is complete. Make sure all equipment is properly installed on
ページ11に含まれる内容の要旨
ENGLISH Adjustment Step 14 Release the hand brake (on the right leg) and move the worksurface up to highest level. Push in the cover located behind each leg to access the adjustment point. NOTE: The covers on the legs will not open unless the worksurface has been lifted to it’s full height. The worksurface will not lower unless the covers have been completely closed. Maintain equal amount of tension on both legs by alternating the tension adjustment from one leg to the other using a 14mm
ページ12に含まれる内容の要旨
APPENDIX A - Minimize Lift Tension WARNING. Before removing mounted equipment (monitor, arm, stand CPU, etc.), from desk, or to prepare for shipping or storing the desk it is extremely important to minimize the lift tension. Failure to install these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury. 1. Release the hand brake (on the right leg) and move the worksurface up to highest level. 2. Push in the cover located behind each le
ページ13に含まれる内容の要旨
ENGLISH APPENDIX B - Inserting Stop Screws WARNING. Before shipping or storing the desk, or in cases where the desk is placed on it’s back or side*, it is extremely important that the 4 stop screws be re-inserted. Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury. 1. Follow instructions in Appendix A to minimize lift tension. 2. Push the desk down to its lowest position. 3. Insert 2 stop screws at the bottom
ページ14に含まれる内容の要旨
Set Your Workstation to Work For YOU! Confi gure su estación de trabajo para que trabaje para USTED. Ajustez votre station de travail en fonction de VOS besoins ! Richten Sie Ihren Arbeitsplatz so ein, dass er für SIE arbeitet! Stel uw werkstation zo in dat het voor U werkt! Approntare la stazione di lavoro nella posizione ergonomica ottimale. 一人ひとりにピッタリのワークステーション! 按照您自身的需要设置工作站！ Learn more about ergonomic computer use at: Más información sobre el uso ergonómico de ordenadores: Apprenez-
