ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS
HEAVY DUTY FIXED WALL MOUNT
Model: PSH-2000
Specifications:
• Accomodates Akira and Orion 84" displays
without interface bracket; accomodates other
large flat panel displays with optional interface
bracket.
NOTE: Interface bracket, if required, will result in
additional installation depth. Contact Chief for
details.
• Designed for installation on dual wood studs (16"
or 24" on center).
• Weight capacity of 250 lbs (113 kg).
BEFORE YOU BEGIN
CAUTION: To prevent d
ページ2に含まれる内容の要旨
Model: PSH-2000 Installation Instructions IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: It is the installer’s responsibility to make sure the structure to which this unit is attached can support five times the combined weight of all equipment.
ページ3に含まれる内容の要旨
Installation Instructions Model: PSH-2000 TOOLS REQUIRED FOR INSTALLATION • Drill and 7/32" drill bit Table 1: Parts • 13mm wrench •1/2" wrench Item Description Qty • Phillips screwdriver, #2 10 PLATE, Wall 2 • M5 Hex Key (provided) 20 BRACKET, Static 2 • 3/16" Hex Key (provided) 30 BRACKET, Side Support 2 • 5/32" Hex Key (provided) 40 LATCH 2 50 SPACER, 0.194" ID x 0.375" OD x 0.032" 8 NOTE: Other tools may be required depending on your method of installation. 60 SCREW, Button Head Cap, 10-2
ページ4に含まれる内容の要旨
Model: PSH-2000 Installation Instructions ASSEMBLY AND INSTALLATION NOTE: Read the Warnings and Cautions on page 2. INSTALL MOUNTING BUTTONS Installation of the mounting buttons is dependent on your specific display. Three options are provided: • Akira 84" and Orion 84" displays • Modular 84" displays • Other large flat panel displays Install buttons (90) at these AKIRA 84" AND ORION 84" DISPLAYS 6 mounting hole locations. 1. Using key (140), insert screw (80) through button (90) and instal
ページ5に含まれる内容の要旨
Installation Instructions Model: PSH-2000 ASSEMBLE STATIC BRACKETS ASSEMBLE SIDE SUPPORTS 1. Using key (160), loosely install screws (60) through 1. Using key (150), loosely install support (30) to plate latch (40) and spacers (50) into threaded holes in (10) with screws (130) (See Figure 7). Ensure lip of bracket (20) (See Figure 5). Ensure latch (40) is support (30) covers edge of plate (10). installed on the end of bracket (20) with the square 2. Repeat for other 3 corners. cutout. 3. O
ページ6に含まれる内容の要旨
Model: PSH-2000 Installation Instructions INSTALL MOUNT TO WALL 1. Determine approximate mounting location, keeping in Left of center installation mind the display size. Lag Bolt & Washer (8 Places) WARNING: The mount must be installed on two or three wood studs (or other equivalent vertical or horizontal supporting framework). Do not mount to single wood studs. Failure to properly install unit can result in serious personal injury or damage to equipment! 2. Use a stud sensor to locate
ページ7に含まれる内容の要旨
Installation Instructions Model: PSH-2000 2. Using key (150), loosely install brackets (20) to plates INSTALL STATIC BRACKETS (10) with screws (130) according to dimension noted AKIRA 84", ORION 84", AND MODULAR 84" in previous step. Ensure that brackets (20) are DISPLAYS installed so that the latches (40) are towards the top of the mount. 1. Using key (150), loosely install brackets (20) to plates (10) with screws (130) (See Figure 10). Ensure the • 14" horizontal dimension: Install br
ページ8に含まれる内容の要旨
Model: PSH-2000 Installation Instructions 5. Repeat for second latch (40). INSTALL DISPLAY 6. Connect cables to display as required. WARNING: Display is very heavy! Ensure display can be safely lifted and maneuvered as required to install REMOVE DISPLAY on mount. Failure to take adequate precautions can result in serious personal injury or damage to equipment! WARNING: Display is very heavy! Ensure display can be safely lifted and maneuvered as required to remove 1. Ensure latches (4
