ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
Medium Flat Panel Steel Stud Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
JWDSK Series
ページ2に含まれる内容の要旨
JWDSK Series Installation Instructions DISCLAIMER Milestone AV Technologies, Inc., and its affiliated corporations CAUTION: A CAUTION alerts you to the possibility of and subsidiaries (collectively, "Milestone"), intend to make this damage or destruction of equipment if you do not follow the manual accurate and complete. However, Milestone makes no corresponding instructions. claim that the information contained herein covers all details, conditions or variations, nor does it provide for
ページ3に含まれる内容の要旨
TOGGLER Ă Installation Instructions JWDSK Series TOOLS REQUIRED FOR INSTALLATION AND PARTS 1/2" (Ø13mm) (3/16") (5/32") I/M A (1) x1 Interface Bracket C (4) Kit 8-32 x 3/8" B (2) (Including Hardware) E (4) (1/4") x 1 D (4) (1/4"-20 x 1-3/4") F (4) (1/4"-20 SNAP TOGGLE BB) G (1) 3/16" 3
ページ4に含まれる内容の要旨
JWDSK Series Installation Instructions Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation. It should also be noted that no other equipment
ページ5に含まれる内容の要旨
Installation Instructions JWDSK Series MOUNT INSTALLATION After determining the site meets the installation requirements: Drywall 1. Identify desired mounting location on wall. 2. Using a stud finder or similar method locate studs. 3. Align mounting holes in mount with studs making sure Plastic Straps mounting holes are centered on studs. (See Figure 2) 4. Mark location of three mounting holes on wall. 5. Drill four 1/2" (Ø13mm) holes. (See Figure 2) 1/2" (Ø13mm) x4 (F) x4 Figure 3 7. Holding p
ページ6に含まれる内容の要旨
JWDSK Series Installation Instructions Display Installation Steel Stud 1. Determine mounting pattern on display. Drywall Plastic Cap WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer! WARNING: IMPROPER INSTALLATION CAN LEAD TO Plastic Straps ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw length must not exceed the depth of threaded mounting insert i
ページ7に含まれる内容の要旨
Installation Instructions JWDSK Series CAUTION: Ensure that adequate cable slack exists for movement of display, and that cables will not be pinched by installation of cover (B) or screws (C). 2. Carefully insert cables in cavity located in lower portion of mount arm (See Figure 9). 3. Using Phillips screwdriver, install cover (B) with two screws (C). (See Figure 9) 1 x2 Cable Path Figure 7 (typical) 2. Align two screws in display back with upper teardrop (B) x 2 mounting holes in moun
ページ8に含まれる内容の要旨
JWDSK Series Installation Instructions Adjust display Roll, Pitch, and YAW tension 1. Disconnect all wires and cable from the display. 2. Remove two Lower screws securing display to Centris cup. 3. Loosen two Upper screws securing display. 4. Lift display upward and away from mount. 5. Using a hex head wrench turn the tension adjustment screw clockwise to increase tension, or counter-clockwise to decrease tension. (See Figure 11) 6. Re-install display. Figure 11 8
ページ9に含まれる内容の要旨
Installation Instructions JWDSK Series 9
ページ10に含まれる内容の要旨
JWDSK Series Installation Instructions 10
ページ11に含まれる内容の要旨
Installation Instructions JWDSK Series 11
ページ12に含まれる内容の要旨
JWDSK Series Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands Chief Manufacturing, a division of P +31 (0)40 2668620 Milestone AV Technologies, Inc. F +31 (0)40 2668615 Asia Pacific A Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. 8832-000220 RevC ©2008 Milestone AV Technologies P +86-755-8996
