ページ1に含まれる内容の要旨
®
PowerScan PD7100 Corded
Linear Imaging Barcode Reader
Product Reference Guide
ページ2に含まれる内容の要旨
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non- exclusive, re
ページ3に含まれる内容の要旨
Table of Contents Chapter 1. Introduction.............................................................................................................. 1 About this Guide .................................................................................................................... 1 Manual Overview ................................................................................................................... 1 Manual Conventions .........................................................
ページ4に含まれる内容の要旨
Chapter 5. RS-232 ONLY Interface........................................................................................... 47 Introduction ......................................................................................................................... 47 RS-232 Standard Factory Settings .......................................................................................... 47 Baud Rate ..................................................................................................
ページ5に含まれる内容の要旨
Label ID Control ............................................................................................................105 Label ID Symbology Selection .........................................................................................106 Case Conversion .................................................................................................................112 Character Conversion ...............................................................................................
ページ6に含まれる内容の要旨
GS1 DataBar Limited Enable/Disable ............................................................................... 156 GS1 DataBar Limited GS1-128 Emulation ......................................................................... 156 GS1 DataBar Limited Minimum Reads .............................................................................. 157 Code 39 ............................................................................................................................ 158 Code 39 Ena
ページ7に含まれる内容の要旨
Datalogic 2 of 5 Stitching ................................................................................................216 Codabar .............................................................................................................................217 Codabar Enable/Disable ..................................................................................................217 Codabar Check Character Calculation ...........................................................................
ページ8に含まれる内容の要旨
Appendix A. Technical Specifications..................................................................................... 271 Standard Cable Pinouts ....................................................................................................... 273 Appendix B. Standard Defaults .............................................................................................. 275 Default Exceptions ...............................................................................................
ページ9に含まれる内容の要旨
Chapter 1 Introduction About this Guide This Product Reference Guide (PRG) is provided for users seeking advanced technical information, including connection, programming, maintenance and specifications. The Quick Reference Guide (QRG) and other publications associated with this product are downloadable free of charge from the website listed on the back cover of this manual. Typically, units are factory-programmed for the most common terminal and communi- cations settings. If you need to modi
ページ10に含まれる内容の要旨
Introduction Chapter 11, Symbologies defines options for all symbologies and provides the program- ming barcodes necessary for configuring these features. Appendix A, Technical Specifications lists physical and performance characteristics, as well as environmental and regulatory specifications. It also provides standard cable pin- outs. Appendix B, Standard Defaults references common factory default settings for reader features and options. Appendix C, LED and Beeper Indications supplies table
ページ11に含まれる内容の要旨
Technical Support Technical Support Datalogic Website Support The Datalogic website (www.scanning.datalogic.com) is the complete source for technical support and information for Datalogic products. The site offers product support, prod- uct registration, warranty information, product manuals, product tech notes, software updates, demos, and instructions for returning products for repair. Reseller Technical Support An excellent source for technical assistance and information is an authorized D
ページ12に含まれる内容の要旨
Introduction NOTES ® 4PowerScan PD7100 Corded
ページ13に含まれる内容の要旨
Chapter 2 Getting Started About the Reader Advancements in the LED technology used in this reader significantly improve the illumination of the target field of view, resulting in higher scan efficiency. Whether used in Single Trigger or Continuous Mode, the ergonomic design of the reader will help to promote comfortable han- dling during extended periods of use. See Interface Selection on page 11 for a listing and descriptions of available interface sets by model type. Unpacking Check careful
ページ14に含まれる内容の要旨
Getting Started Setting Up the Reader Follow the steps provided in this section to connect and get your reader up and communicating with its host: 1. Install the Interface Cable 2. Select the Interface Type 3. Configure Interface Settings (only if not using factory settings for that interface) 4. Configure Other Features (if modifications are needed from factory settings) Install the Interface Cable The reader cable connection is secured using the “clamshell” retainer referenced in the enlarged
ページ15に含まれる内容の要旨
K e W y b e o d a r g d e Setting Up the Reader Other connection types are described below and illustrated in Figure 2. USB Connection — Connect the reader to a USB port on the terminal/PC using the correct USB cable for the interface type you ordered. Reference Figure 2. IBM Connection — Connect the reader to the IBM port on the terminal/PC using the cor- rect IBM cable. Reference Figure 2. Keyboard Wedge Connection — The Keyboard Wedge cable has a ‘Y’ connection from the reader. Connect t
ページ16に含まれる内容の要旨
Getting Started Using the Programming Barcodes This manual contains feature descriptions and barcodes which allow you to reconfigure your reader. Some programming barcode labels, like the Standard Product Default Settings on page 9, require only the scan of that single label to enact the change. Most of the programming labels in this manual, however, require the reader to be placed in Programming Mode prior to scanning them. Scan an ENTER/EXIT barcode once to enterProgramming Mode. Once the
ページ17に含まれる内容の要旨
Resetting the Standard Product Defaults Resetting the Standard Product Defaults If you aren’t sure what programming options are in your reader, or you’ve changed some options and want the factory settings restored, scan the Standard Product Default Settings barcode below. This will copy the factory configuration for the currently active interface to the current configuration. Factory defaults are based on the interface type. Configure the reader for the correct interface before scanning this
ページ18に含まれる内容の要旨
Getting Started NOTES ® 10 PowerScan PD7100 Corded
ページ19に含まれる内容の要旨
Chapter 3 Interfaces Interface Selection Each reader model will support one of the following sets of host interfaces: General Purpose Models (5 volt supply) RS-232 RS-232 OPOS USB Keyboard Wedge Retail Point of Sale Models (4 to 14 volt supply) RS-232 RS-232 OPOS USB IBM 46XX Configuring the Interface Scan the programming barcode from this section which selects the appropriate interface type matching the system the reader will be connected to. Next, proceed to the corre- sponding chapter in thi
ページ20に含まれる内容の要旨
Interfaces Table 1. Available Interfaces RS-232 FEATURES RS-232 standard interface Select RS232-STD RS-232 Wincor-Nixdorf Set RS-232 Select RS232-WN Interface Features starting on page 47 RS-232 for use with OPOS/UPOS/JavaPOS Select RS-232 OPOS USB Com to simulate RS-232 standard interface a Select USB-COM-STD IBM FEATURES IBM-46xx Port 5B reader interface Set IBM Interface Select IBM-P5B Features starting on page 89 IBM-46xx Port 9B reader interface Select IBM-P9B USB-OEM FEATURES Set USB-OE
