ページ1に含まれる内容の要旨
Pow-R-Command 1000 — LCD Display
Quick Start Guide
Instruction Leaflet IL01412010E
Effective June 2006
Introduction
This is the Quick Start Guide for the PRC1000 LCD programming
Primary Handle
display. A worksheet of information that will be needed to complete
this startup is found on Page 6 of this guide. Make sure you have all
the listed information available before starting, either by filling in the
worksheet, or from job documents.
Control Handle
Sever
ページ2に含まれる内容の要旨
LCD Programming Procedure CONFIGURE DATE/TIME 1. Press any key to begin. The Eaton logo will be displayed: Change Date__08/23/06 Change Time 11:37 AM Change DST MANUAL After a few seconds, the firmware version will be displayed: St: mm/dd End: mm/dd FIRMWARE VERSION A1 Change Astro Loc. After a few more seconds, the initial status screen will be displayed: Use UP/DOWN to select Change Date
ページ3に含まれる内容の要旨
Hit SEL to select Group A. The following menu is displayed: B. Associate Inputs With the Group If a switch input will be associated with this group, use UP/DOWN to CONFIGURE GROUP A highlight the Associate Inputs. Hit SEL to move to the input select screen: Group A GRPA ON OFFICE LIGHTING INPUT for GROUP A is currently #7 Associate Loads______ Change input to: Associate Inputs Input 7 DI01 (OFF) Modify Schedules Maintained + 5 min_ Modify Description A. Asso
ページ4に含まれる内容の要旨
C. Set Group Description Verify that the group description on the fifth line of the COMMAND GROUPS screen is the correct description for this group. If not, repeat Use UP/DOWN to highlight the MODIFY DESCRIPTION option and hit Step 4C — Configure Breaker Group A — Set Group Description. SEL. The SELECT DESCRIPTION screen will be displayed: 5. Repeat Step 4 for each Group B through P SELECT DESCRIPTION 6. Schedule Groups For Group A The final step in initial setup is to enter the schedules for
ページ5に含まれる内容の要旨
Hit SEL to choose the DAYS: item. The following screen is displayed: When the days, start time, and end time have all been entered, hit BACK to return to the MODIFY SCHEDULES screen. The newly entered schedule will now be in the list, as shown in the following PICK SCHEDULE DAYS example: Weekdays____________ Weekends MODIFY SCHEDULES FOR Clear All Days Group A OFFICE LIGHT Pick specific days: Use SEL to edit sch. Yes: Days --ON-- --OFF- No: SMTWTFS Weekday 09:30A 05:30PP (empty schedu
ページ6に含まれる内容の要旨
PRC1000 Programming Worksheets 1. Programmer password: _ _ _ _ _ _ _ _ 2. Date/Time: Daylight Savings Time Used: NONE / AUTO / MANUAL DST Manual dates: Start: _ _ / _ _ (mm/dd) End: : _ _ / _ _ (mm/dd) 3. Location Latitude (-90 to +90): __°__’ Longitude (-180 to +180): __°__’ Timezone (-12hrs to +12hrs): __ hrs 4. Breaker Groups Mark the groups each circuit is part of. Copy this page as needed for additional panels. TABLE 1. BREAKER GROUPS GROUPS GROUPS CIRCUIT AB C D E F GH I J K L M NOP
ページ7に含まれる内容の要旨
5. Schedules Mark schedule details. Copy as needed for additional schedules Group ____: Weekends Weekdays S M T W T F S Start _ _ : _ _ AM / PM End: _ _ : _ _ AM / PM Group ____: Weekends Weekdays S M T W T F S Start _ _ : _ _ AM / PM End: _ _ : _ _ AM / PM Group ____: Weekends Weekdays S M T W T F S Start _ _ : _ _ AM / PM End: _ _ : _ _ AM / PM Group ____: Weekends Weekdays S M T W T F S Start _ _ : _ _ AM / PM End: _
ページ8に含まれる内容の要旨
Eaton Electrical Inc. 1000 Cherrington Parkway Moon Township, PA 15108-4312 United States tel: 1-800-525-2000 www.EatonElectrical.com © 2006 Eaton Corporation All Rights Reserved Printed in USA Publication No. IL01412010E / Z4308 June 2006
