ページ1に含まれる内容の要旨
QSW8209
LCD Baby Monitor
Wireless Camera
Visit Us on the Web at http://www.q-see.com
Rev 092507
ページ2に含まれる内容の要旨
C C C Cont ont ont ontent ent ent ents s s s 1 Packing List 2 Diagram 3 Structure 4 Installation 5 Specifications 6 FCC and EU
ページ3に含まれる内容の要旨
1. Packing List 1) 2.4GHz Wireless Camera ╳ 1 2) 2.4GHz Wireless Receiver ╳ 1 3) AV cable ╳ 1 4) Power Adapter for camera ╳ 1 5) Power Adapter for receiver ╳ 1 Note: AA Batteries are not included 2. Diagram
ページ4に含まれる内容の要旨
3. Structure 3-1. Layout of Camera 3-2. Layout of Receiver
ページ5に含まれる内容の要旨
4. Installation 4-1. Setting up the Camera 1. Setup the camera in the desired location 2. Connect the camera to the adapter and then slide the power switch to the ON position Note: --This camera can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment on the back of the camera with their polarities in the correct position. --The AC adapter will work instead of batteries after it is plugged in. If the
ページ6に含まれる内容の要旨
camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries. * The camera can run off of batteries for up to 5 hours (IR OFF) 3. Rotate the rounded head of the camera to the desired angle for surveillance. 4-1-1. Camera channel setup 1. On the right side of the camera there is a channel selector switch marked CH1,CH2,CH3,CH4. If you have multiple cameras you would set each one on a different channel to avoid
ページ7に含まれる内容の要旨
2. Press the channel button on the receiver to select the same channel as the camera. When the channels match the picture will be displayed on the screen. 4-1-3. Camera alarm setup 1. The camera provides Motion Detection and Sound Detection. For each mode you can select 3 sensitivity levels: Low, Middle, High. Motion Alarm Setup: This alarm will detect movement in front of the camera. If you slide the alarm setting switch to the Motion position and select the S
ページ8に含まれる内容の要旨
you press the Eliminate Alarm Button. Within 1 minute the motion alarm starts the next alarm circle. Sound Alarm Setup: This alarm will detect sound. If you slide the alarm setting switch to the Sound position, and select the Sensitivity level, the system enters sound alarm mode. When sound is detected, the alarm sounds until you press the Eliminate Alarm Button. When the alarm sounds the screen will also display the video unless you have pressed the Sleep button. Within 1 minute the soun
ページ9に含まれる内容の要旨
Note: --This receiver can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment at the back of the camera with their polarities in the correct position. --The AC adapter will work instead of batteries after it is plugged in. If the camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries. * The camera can run off of batteries for up to 5 hours. 2. Adjust the volume control
ページ10に含まれる内容の要旨
3. Set the channel of the receiver to the same channel as the camera by pressing the channel button continuously, the pictures will display on the screen when the channels match. Note ： ： ： ： For clearer pictures you can connect the receiver to a monitor/TV with the included AV cable (yellow for video and red for audio). 4-2-1. Operation of the Receiver 1. Volume adjustment
ページ11に含まれる内容の要旨
Slide “Volume Switch” to adjust the volume of the receiver. 2. Channel selection Press “CH button” to select the desired channel. 3. Channel Looping Hold the “CH button” for three seconds to enter the loop mode. All the available channels will be displayed one by one (default interval is 5 seconds). 4. Sleep Mode Press the “Sleep Button” to shut down the LCD display and keep the voice function. Press the button again and recall the normal working mode. This can save energy. 5. Eliminat
ページ12に含まれる内容の要旨
Imaging Sensor Type CMOS PAL:720×480 Pixels; Picture Total Pixels NTSC: 720×576 Pixels Horizontal Resolution 380 TV Lines View Angle PAL:55°; NTSC:55° Minimum Illumination 0Lux BandWidth 18M Night Vision Range 5m CAMERA Battery Working Time 5 hours (IR OFF) Motion Detection Distance 5m (16ft) Sound Control Sensitivity >63dB Consumption Current 120mA(IR OFF)(Max.) & 220mA(IR ON)(Max.) Power Supply DC +8V Dimensions(W×D×H) 86*48*135 mm (3.5*2*5.5 in) Weight 146 g (5.2 oz) LCD Scr
ページ13に含まれる内容の要旨
* Actual transmission range may vary according to weather, Location, interference and building construction. * All the specifications are subject to minor change without prior notice. 6. FCC information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or m
ページ14に含まれる内容の要旨
EU Environmental Protection Electrical waste products (discharged batteries) should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. TRADEMARKS All brand names and products are registered trademarks of their respective Companies. DISCLAIMER The information in this document is subject to change without notice. The manufacturer makes no representations or warranties
ページ15に含まれる内容の要旨
LEGAL DISCLAIMER Warning: Your security camera is a quality digital product. You have to take utmost care while handling this product in order to ensure its reliability & durability. Digital Peripheral Solutions Inc. 8015 E Crystal Drive. Anaheim, CA 92807, 1-877-998-3440. Q-See Tech Support in U.S.A. Mon-Fri: 9 am 5 pm PST. TEL:1-877-998-3440 E-mail: ts@dpsi-usa.com Website: www.q-see.com
