ページ1に含まれる内容の要旨
1/2” IMPACT WRENCH
WITH 2” EXTENDED ANVIL
93566
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web Site at www.harborfreight.com
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this manual or
any artwork contained herein may be rep
ページ2に含まれる内容の要旨
THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: Model______________ Serial No._____________ Purchase Date_______________ SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Material: Cast aluminum housing Extended Anvil: 2-1/4” Drive Size: 1/2” Square drive Maximum Torque: 250 Ft. Lbs. Air Inle
ページ3に含まれる内容の要旨
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles and hearing protection. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 9. Maintain tools with care. Keep tools clean for better and safer performance. Follo
ページ4に含まれる内容の要旨
Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints Crystalline silica from bricks
ページ5に含まれる内容の要旨
Operation (continued) Warning!! This Impact Wrench supplies powerful torque and is designed to be operated with two hands. Failure to operate the Impact Wrench with two hands may result in serious injury. Refer to FIGURES 1 through 3 on page 6, and the Assembly Drawing on page 8. Note: Turn off your air compressor and disconnect the air hose when you are changing sockets. After you attach the socket, attach the air hose and turn the air compressor on. 4. Select the appropriate size 1/2” drive
ページ6に含まれる内容の要旨
R F 1 Maintenance (Cont’d) 4. Weekly, or more often if used on a daily basis, use a grease gun (not included), to inject grease into the Grease Fitting. Put in only a drop or two. See FIGURE 3. 5. If you do not use an inline oiler/filter system, lubricate the tool daily by holding it so that the Air Inlet (10) is facing up. Squeeze the Trigger (4), and place one or two drops of oil into the Air Inlet (10). Squeezing the Trigger (4) allows the oil to circulate in the motor. Figure 1 Air Inlet
ページ7に含まれる内容の要旨
Parts List Part # Description Quantity Part # Description Quantity 1 Housing 1 24 Cylinder 1 2 Valve Sleeve 1 25 Rotor 1 3 Forward/Reverse Valve 1 26 Rotor Blade 6 4 Trigger 1 27 Front End Plate 1 5 Pin 1 28 Ball Bearing 1 6 Bushing 1 29 Rear End Plate 1 7 Valve Stem 1 30 Pin 1 8 Ball Bearing 1 31 Spring 1 9 Spring 1 32 Pin 1 10 Air Inlet 1 33 Rear Gasket 1 11 Screen 1 34 Rear Cover 1 12 Air Regulator 1 35 Washer 4 13 O Ring 1 36 Screw 4 14 Spring 1 37 Rubber Sleeve 1 15 Oil Seat 1 38 Exhaust De
ページ8に含まれる内容の要旨
Parts/Assembly Diagram SKU 93566 For technical questions please call 1-800-444-3353. Page 8
