ページ1に含まれる内容の要旨
18 VDC - IMPACT DRIVER
94371
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may
differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2006 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technica
ページ2に含まれる内容の要旨
Specifications Item Description Battery 18 V D C , 1.3 AH , N i-C d type Torque 1044 IN .LB S (m axim um ) Speed 1700 B PM ; 0-1600 R PM Sw itch Toggle, Forw ard / R everse Drive S ize ¼ inch Weight 4.15 lbs. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual
ページ3に含まれる内容の要旨
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles and ear plugs when using the Impact Driver. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Remove adjusting keys and
ページ4に含まれる内容の要旨
Battery Precautions 1. Read all instructions and warnings on the battery before charging the battery. 2. To avoid accidents, charge the supplied battery only. Do not use a different charger with this battery. 3. Do not expose the battery to rain or wet conditions. 4. To avoid damage of cable and plug, never pull the cable to disconnect the charger. 5. Do not use the charger if the cable or plug are damaged. 6. Repairs should be carried out by a qualified technician. 7. Do not touch the battery
ページ5に含まれる内容の要旨
Unpacking When unpacking, check to make sure the following parts are included: Impact Driver, Battery, Charger Base, and Charger Adapter. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Operation CHARGING BATTERY The Battery (30) does not come charged from the factory. Charge before using. Refer to photos on the next page. 1. Push the two side buttons in on the Battery, then slide the Battery off the Impact Driver handle. 2. Slide
ページ6に含まれる内容の要旨
Charger Base (48) Charging Indicator Battery (30) Charger Adapter (49) INSERTING BATTERY Caution: Before inserting the Battery into the tool, be certain that the Trigger Switch (21) is in the Off position. 1. Push the Forward/Reverse Button (31) to the center position to lock the Switch in the Off position. 2. Insert Battery into the receptacle at the handle-bottom of the Impact Driver. 3. Secure the Lock-spring Clasps to each side of the handle. SCREWDRIVER 1. Insert a hex screwdr
ページ7に含まれる内容の要旨
Driver Bit (not supplied) Forward / Reverse Rotation Button Trigger Switch (21) Variable Speed Lock-spring Clasps Troubleshooting Symptom Possible Cause Remedy Trigger Switch locked Forward / Reverse Move button to the left or in place. button in center right for forward or reverse position. operation. Impact Wrench Battery weak. Recharge Battery operates slowly or completely. without force. Impact Wrench does Battery completely Recharge Battery not turn on. discharged. completely. Battery will
ページ8に含まれる内容の要旨
Parts List Part Part No. Description Qty No. Description Qty 1 Left Housing 1 40 Wire (Red) “+” 1 2 Right Housing 1 41 Wire (Black) “-” 1 3 Strap 1 42 Wire (Yellow) 1 4 Axle Bearing 1 43 Wire (Blue) 1 5 Bushing - 1 1 44 Magnet - Ring 2 6 Bushing - 2 1 45 Capacitor 2 7 Center Shaft 1 46 Washer 1 8 Battery Housing 1 47 Bushing 1 9 Steel Ball 3 48 Charger Base 1 11 Inner Gear 1 49 Charger Adapter 1 12 Motor Housing 1 13 Washer M4 4 14 Motor 1 16 Planet Gear 2 17 Planet Shaft 2 18 Shaft 1 19 Block
ページ9に含まれる内容の要旨
Assembly Drawing PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS S
