ページ1に含まれる内容の要旨
SM-CDM1042
CD/MP3-RECEIVER CD/MP3-
Instruction manual
ページ2に含まれる内容の要旨
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents TABLE OF CONTENTS ..................................................................................................... 2 IMPORTANT SAFEGUARDS .............................................................................................. 3 INSTALLATION/
ページ3に含まれる内容の要旨
Important safeguards Read carefully through the manual to familiarize yours with this high-quality sound system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit. Do not attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes. Make sure that pins or other
ページ4に含まれる内容の要旨
Installation/Connections First complete the electrical connections, and then check them for correctness. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. Before installing the unit, please remove two screws on the top. Before the installation 1. Remove the old unit from the dashboard. Remove the outer trim frame
ページ5に含まれる内容の要旨
Installation method A After inserting the holder into the dashboard, select the appropriate tab and bend them inwards to secure the holder in place. Insert fingers into the groove in the front of frame and remove it. Insert the levers supplied with the unit to the grooves at both sides. The unit can be installed or removed from the dashboard. 5
ページ6に含まれる内容の要旨
Installation method B Note: Outer trim frame, hook, and mounting sleeve are not used for this installation. This is only intended as a general guide; contact the vehicle's manufacturer for specific instructions. This method of installation uses the screw holes at the sides of the unit and the holes of the existing vehicle mounting bracket. 1. Align the screw holes of the mounting bracket supplied with the car and the screw holes of the main unit. Tighten the 2 screws on each side of the unit. T
ページ7に含まれる内容の要旨
To detach the front panel The front panel of the unit may be removed as a theft deterrent. After removing the front panel, use the case provided to keep the front panel from getting damaged. 1. Press the OPEN button to flip down the front panel. 2. Grasp the right side of the front panel, and then gently push the front panel towards the left side before pulling it out from the unit. 3. Store the front panel in the protective case provided for safekeeping. To attach the front panel Hold the right
ページ8に含まれる内容の要旨
Connection scheme Notes: In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level. Prohibit to make the conductors of auto antenna and ground touch with each other. 8
ページ9に含まれる内容の要旨
Accessories Name pcs 1 Hexagon nut M5 T (3.5 mm) 1 2 Mounting box (0.6 mm) 1 3 Left key (1.0 mm) 1 4 Right key (1.0 mm) 1 5 Metal bar (0.8 mm) 1 6 ISO connector 1 7 Plain washer =5 mm 1 8 Carrying case 1 9 Outer trim ring 1 10 Spring washer =5 mm 2 11 Screw 5X5 mm 4 12 Screw 5X25 mm 1 13 Screw M5 5X29.3 mm 1 14 Customer information 1 15 Warranty card 1 16 Instruction manual 1 9
ページ10に含まれる内容の要旨
Panel controls Front panel 1. PWR/MUTE button 2. SEL button 3. MOD button 4. AUX in jack 5. No 1/PLAY/PAUSE button 6. No 2/SCN button 7. No 3/RPT button 8. No 4/SHF button 9. No 5 button 10. No 6 button 11. No 7/TA/PTY button 12. No 8/AF/REG button 13. No 9/DISP button 14. No 0/BAND button 15. TEL MENU button 16. PREVIOUS/* button 17. NEXT/# button 18. button 19. OPEN button 20. AMS/ button 21. IR sensor 22. Microphone 23. LCD display 24. USB slot 25. VOL+/VOL- buttons 10
ページ11に含まれる内容の要旨
Inner panel Press the OPEN button on the front panel to flip it down. 26. SD/MMC-card slot 27. Disc slot 28. EJECT button 29. Light indicator 30. RESET button 11
ページ12に含まれる内容の要旨
Remote Controller (RC) 1. MODE button 2. POWER button 3. No 2/SCN button 4. No 1/PLAY/PAUSE button 5. No 4/SHF button 6. No 8/AF/REG button 7. No 7/TA/PTY button 8. PREVIOUS/* button 9. SEL/ENTER button 10. button 11. TEL MENU button 12. 3/RPT button 13. No 5 button 14. No 6 button 15. No 9/DISP button 16. NEXT/# button 17. No 0/BAND button 18. VOL+/VOL- buttons 19. AMS/ button 12
ページ13に含まれる内容の要旨
Changing the battery 1. Press the catch and at the same time pull out the battery tray. 2. Insert the 1 x lithium battery, type CR2025 (3V) battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. Warning: Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. Do not recharge, short, disassemble or heat the battery or dispose it in a fire. Do not expose or bring into contact the battery w
ページ14に含まれる内容の要旨
General operations Power button Press any button (except OPEN) or insert disc to switch the unit on. Press POWER button for several seconds to switch the unit off. Volume control Press VOL+/VOL- buttons to adjust the volume level. Audio settings adjustment Press SEL button until the display shows: VOL => BAS => TRE => BAL => FAD. Press VOL+/VOL- buttons to adjust each setting. Press SEL button for 2 seconds to enter the menu mode. Press it repeatedly to choose the needed item: TA SEEK/ALARM, MAS
ページ15に含まれる内容の要旨
During AF search, PI stations and non-RDS (Radio Data Station) stations with strong signal will be masked, in the latter case, the non-RDS stations may cause interference, resulting the real AF to be masked due to the misjudgment of the radio under interference. Press VOL+/VOL- buttons to select the desired mode: MASK DPI and MASK ALL. - MASK DPI: To mask only the AF with different PI. MASK ALL: To mask both PI and strong signal non-RDS station. TA VOL Choose the TA volume level. RETUNE mode
ページ16に含まれる内容の要旨
BEEP OFF: the beep is disabled. STEREO/MONO: FM stations are usually listened in stereo mode. However, if the signal weak or reception is not as good, switching to MONO mode usually improves the overall sound quality. Choose FM STEREO or MONO audio effect. LOCAL/DX: In urban settings, most stations are strong enough and stations are usually listened in LOCAL mode. However, if a station seems too distant to be received well, try switching to DISTANT mode. Choose local reception or distant recep
ページ17に含まれる内容の要旨
Information display Press DISP button to operate as the conversion of each display mode as follows: - In case of receiving a RDS station In radio mode: PS -> CT -> FREQ -> P TY In CD mode: CD -> CT -> (ID3 TAG) -> PS -> FREQ -> PTY * In case of no receiving CT or PTY Information, the display shows as “NO CLOCK” or “NO PTY”. - In case of receiving a non RDS station In radio mode: “NO CLOCK” -> FREQ-> ”NO PTY” In CD mode: CD -> “NO CLOCK” -> FREQ -> “NO PTY” Each displaying time is several second
ページ18に含まれる内容の要旨
Radio operations Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. To select a radio band In radio mode, press the BAND button repeatedly to select a radio broadcasting band you need. FM 1 => FM 2 => FM 3 => MW1 => MW2. Auto/Manual tuning Automatic search mode: Press NEXT or PREVIOUS buttons, the automatic search will start. It will search upward or downward for the
ページ19に含まれる内容の要旨
Press a preset button (1-6) briefly to recall the stored station. In case of RDS mode, the strongest AF is selected after AF searching. Auto store/Preset scan Preset scan: Press the AMS button to scan each preset station in the memory of the current band. Finally the radio will play the first preset station. The memory location indicator on the LCD will flash during the process. Press the AMS again to stop preset scan. Auto store: Press the AMS button for more than 2 seconds to enter the auto s
ページ20に含まれる内容の要旨
RDS function Press AF/REG button to switch ON or OFF the RDS function. Setting RDS mode Whenever RDS is switch on, symbol “AF” appears on the display. Program name is displayed on receiving a RDS station. “AF” starts blinking if the broadcasting signals getting worse. Regional Program Operation Press AF/REG button for 2 seconds to switch on or off region mode. Some broadcasting stations change their program from normal broadcasting to regional broadcasting for a certain time period. When region
