Edelbrock PRO-FLO XT 3527の取扱説明書

デバイスEdelbrock PRO-FLO XT 3527の取扱説明書

デバイス: Edelbrock PRO-FLO XT 3527
カテゴリ: 自動車部品
メーカー: Edelbrock
サイズ: 1.26 MB
追加した日付: 5/21/2013
ページ数: 39
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスEdelbrock PRO-FLO XT 3527の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Edelbrock PRO-FLO XT 3527に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Edelbrock PRO-FLO XT 3527をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Edelbrock PRO-FLO XT 3527のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Edelbrock PRO-FLO XT 3527の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Edelbrock PRO-FLO XT 3527 取扱説明書 - Online PDF
Advertisement
« Page 1 of 39 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Edelbrock PRO-FLO XT 3527を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Edelbrock PRO-FLO XT 3527の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

TABLE OF CONTENTS
Part #3527 and #3528
Introduction.................................................................................................................................................1
Components................................................................................................................................................2
Preliminaries.....................................................................................................................................

ページ2に含まれる内容の要旨

PRIMARY KIT COMPONENTS ❑ Electronic Control Unit/System ECU ❑ Fuel filter ❑ Calibration Module ❑ Fuel rail assembly ❑ Distributor conversion kit ❑ Fuel pressure regulator ❑ Fuel injectors ❑ High pressure fuel pump ❑ ECU power relay/Fuel pump relay ❑ Intake manifold ❑ Manifold Absolute Pressure (MAP) Sensor ❑ Four barrel air valve ❑ Manifold Air Temperature (MAT) Sensor ❑ Idle Air Control (IAC) solenoid, integrated with air valve ❑ Coolant Temperature Sensor (CTS) ❑ Main system harness ❑ Throttle

ページ3に含まれる内容の要旨

TOOLS AND EQUIPMENT HARDWARE AND PARTS RECOMMENDED Use the following checklist for items needed. Use the following checklist for items needed. ❑ Box and open end wrenches ❑ Intake gasket; #3527 kits use Edelbrock gaskets #7201; #3528 kits use gaskets #7235 ❑ Socket set ❑ Pipe plugs, if needed ❑ Distributor wrench ❑ 5/16-inch steel tubing (approximate equal length to fuel pickup ❑ Pliers (channel locks and hose clamp) line in tank) ❑ Screwdrivers (regular and Phillips) ❑ Edelbrock Gasgacinch #930

ページ4に含まれる内容の要旨

MANIFOLD & CARBURETOR HEIGHT VS. PRO-FLO XT HEIGHT 1. Lay a straightedge (such as a yardstick) across the top of the air cleaner from front to back. 2. Measure from block and manifold end seal surfaces to straightedge. 3. Record these measurements (height A and height B). 4. Add height A and height B and divide by two to get the average height. 5. The Pro-Flo XT manifold is 9” tall at the center and 9.125” at the throttle body flange. 6. Compare this to your original measurements. If the Pro-Fl

ページ5に含まれる内容の要旨

FUEL REQUIREMENTS Because the Pro-Flo XT system uses an Oxygen sensor, you must use unleaded fuel only. Leaded fuels will damage the O sensor. If you do use 2 leaded fuel in your vehicle, do not install the O sensor and do not operate the vehicle in the closed loop fuel mode. 2 AUTOMATIC TRANSMISSION CHECK For best performance, economy, and emissions, the shift point must be checked before and after the manifold change. NOTE: This check should be performed ONLY at a sanctioned drag strip or tes

ページ6に含まれる内容の要旨

FUEL SYSTEM Because your Edelbrock Pro-Flo XT system controls fuel delivery very differently than a carburetor, some conversions to your fuel system are necessary. Pro-Flo XT electronic fuel injection requires high and constant fuel volume and fuel pressure. For this reason, a good primary fuel line is critical. The Pro-Flo XT system includes a 3/8-inch high pressure fuel line which must be used as the primary fuel line. The fuel that bypasses the injectors must be returned to the fuel tank vi

ページ7に含まれる内容の要旨

RUBBER RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line enters the tank. This will be the hole for your return line. Insert a short length of 5/16-inch hard line (available at most radiator shops) into the hole and weld it to the sending unit plate. The hard line should extend through the hole 1 to 2 inches on each side of the plate. Connect a length (at least 4 inches) of 5/16-inch rubber return line hose to the hard line that will extend into

ページ8に含まれる内容の要旨

BULKHEAD FITTING METHOD HARD RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line, enters the tank. This will be the hole for your return line. Insert a length of 5/16-inch hard line (available at most radiator shops) into the hole and weld it to the sending unit plate. The hard line should extend through the hole 1 to 2 inches on the outside of the plate. On the inside of the plate, the hard line should follow the contours of the fuel pickup line.

ページ9に含まれる内容の要旨

NOTE: ALL WELDING AND SOLDERING OF THE FUEL SYSTEM MUST BE PERFORMED BY A PROFESSIONAL RADIATOR AND/OR FUEL SYSTEM REPAIR SHOP. FUEL SYSTEM INSTALLATION 1. Drain the fuel tank. 2. Remove all fuel lines from the tank and from the carburetor. 3. Remove the fuel tank. NOTE: While the fuel tank is removed from the car, it is recommended that it be professionally cleaned in order to remove any rust or dirt that may have accumulated inside and which could damage the injectors. 4. Remove the sending u

ページ10に含まれる内容の要旨

ASSEMBLING PRO-CLASSIC HOSE Step One: Cut hose to length, Step Two: Unscrew socket Step Three: Apply Russell Step Four: Hold socket/hose in as straight and square as from hose end. Push hose into assembly lube to threads on vise. Turn nipple with wrench possible, with razor blade-type socket, turning counter- nipple assembly and in socket. until there is less than 1/16" hose cutter or shears. clockwise, until hose is seated Insert nipple into socket/hose between nipple hex and socket. against s

ページ11に含まれる内容の要旨

PRE-INSTALLATION Before installing the induction system, take the following steps to ensure successful installation and performance 1. Check all components thoroughly for damage. 2. Make sure all throttle linkages open entirely and close freely. 3. Make sure all fuel inlet and vacuum ports are free from packing material. 4. Check the installation kit for proper parts. REMOVING THE STOCK CARBURETOR AND MANIFOLD 1. Disconnect battery. 2. For ease of installation, keep all parts in order. CAUTION:

ページ12に含まれる内容の要旨

GASKET SURFACE PREPARATION CAUTION: Replace all gaskets as recommended. Do not use race-type non-embossed gaskets for street applications. Due to material deterioration under street driving conditions, internal vacuum and oil leaks may occur. We recommend Edelbrock gasket #7201 for kit #3527 and #7235 for kit #3528. Do not use Fel-Pro Permatorque Blue gaskets, which are designed for use on stock cast iron intake manifolds only. 1. Check gaskets on head surface and manifold to make sure they a

ページ13に含まれる内容の要旨

SENSORS The Edelbrock Pro-Flo XT system interprets overall engine operating conditions and fuel/spark requirements based on readings from sensors that measure specific engine conditions. The Pro-Flo system includes five sensors: 1) Manifold Absolute Pressure 2) Manifold Air Temperature 3) Coolant Temperature 4) Throttle Position 5) Exhaust Oxygen (O ) 2 MANIFOLD ABSOLUTE PRESSURE SENSOR The Manifold Absolute Pressure sensor, mounted on the intake plenum, converts air pressure (load) in the m

ページ14に含まれる内容の要旨

THROTTLE POSITION SENSOR The Throttle Position Sensor, an integral part of the Pro-Flo throttle body, measures throttle angle. COOLANT TEMPERATURE SENSOR The Coolant Temperature Sensor is a thermistor device like the Manifold Air Temperature sensor. Resistance varies as coolant temperature rises and lowers. The Coolant Temperature Sensor is located at the front of the manifold on the driver’s side. OXYGEN (O ) SENSOR 2 An oxygen sensor, installed on the header collector pipe, measures exhaust ga

ページ15に含まれる内容の要旨

O SENSOR INSTALLATION 2 The exhaust gas oxygen content is determined by the oxygen sensor. The sensor signals the ECU, which compensates when the air/fuel mixture is either rich or lean. NOTE: It is recommended that the O sensor installation be performed by a professional muffler shop. 2 1. Double check header gaskets, replacing if necessary. 2. Drill a 1/2-inch to 9/16-inch hole in the passenger-side header collector reducer, as close to the header flange as possible. (1" to 3" away) NOTE: Bef

ページ16に含まれる内容の要旨

ENGINE HARNESS LAYOUT Catalog #3527, #3528 16 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527

ページ17に含まれる内容の要旨

MAIN SYSTEM HARNESS This diagram illustrates the chassis side of the Pro-Flo XT Main System Harness. Catalog #3527, #3528 17 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527

ページ18に含まれる内容の要旨

Catalog #3527, #3528 18 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527

ページ19に含まれる内容の要旨

MAIN SYSTEM HARNESS This diagram illustrates the engine side of the Pro-Flo XT Main System Harness. Catalog #3527, #3528 19 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527

ページ20に含まれる内容の要旨

Catalog #3527, #3528 20 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Edelbrock 1109 取扱説明書 自動車部品 5
2 Edelbrock 1107 取扱説明書 自動車部品 2
3 Edelbrock 1208 取扱説明書 自動車部品 0
4 Edelbrock 1221* 取扱説明書 自動車部品 1
5 Edelbrock 1222* 取扱説明書 自動車部品 0
6 Edelbrock 1209 取扱説明書 自動車部品 1
7 Edelbrock 1400 取扱説明書 自動車部品 2
8 Edelbrock 1477 取扱説明書 自動車部品 8
9 Edelbrock 1483 取扱説明書 自動車部品 0
10 Edelbrock 15004 取扱説明書 自動車部品 0
11 Edelbrock 15010 取扱説明書 自動車部品 0
12 Edelbrock 15017 取扱説明書 自動車部品 0
13 Edelbrock 15016 取扱説明書 自動車部品 0
14 Edelbrock 15042 取扱説明書 自動車部品 0
15 Edelbrock 15521 取扱説明書 自動車部品 0
16 Sony BP-GL95 取扱説明書 自動車部品 25
17 Sony BP-GL65 取扱説明書 自動車部品 2
18 Philips Epic 50PF9966 取扱説明書 自動車部品 3
19 Philips HTS3011 取扱説明書 自動車部品 2
20 Philips SDJ6040W 取扱説明書 自動車部品 1