ページ1に含まれる内容の要旨
COLOR VIDEO MONITOR
INSTRUCTIONS
BM-H1900SU
BM-H1310SU
For Customer Use:
Enter below the Model No. and
Serial No. which is located on the
rear of the cabinet. Retain this
information for future reference.
UNDER PULSE COLOR BLUE MEMORY
MENU DEGAUSS
SCAN CROSS OFF CHECK MODE
VOLUME PHASE CHROMA BRIGHT CONTRAST
POWER
Model No. VIDEO RGB/ EXT
Y/C
A B COMPO(SDI) SYNC
ON
ENTER OFF
INPUT SELECT
Serial No.
ページ2に含まれる内容の要旨
SAFETY PRECAUTIONS WARNING: INFORMATION CAUTION: Changes or modification not approved by TO PREVENT FIRE OR SHOCK HAZARDS, DO JVC could void the user's authority to operate the NOT EXPOSE THIS APPLIANCE TO RAIN OR equipment. MOISTURE. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
ページ3に含まれる内容の要旨
Thank you for purchasing this JVC color video monitor.Before using it, read and follow all instructions carefully to take fullest advantage of the monitor's performance. CONTENTS SAFETY PRECAUTIONS ----------------------------------- 2 MEMORY MODE --------------------------------------------- 12 FEATURES ------------------------------------------------------ 3 Recall/release of memory mode ------------------------ 12 CONTROLS AND FEATURES (FRONT) --------------- 4 Setting programming of the pict
ページ4に含まれる内容の要旨
CONTROLS AND FEATURES (FRONT) [ BM-H1900SU ] (Front) 4 56p 78 9qwe u i 1 UNDER PULSE COLOR BLUE MEMORY MENU DEGAUSS SCAN CROSS OFF CHECK MODE BRIGHT CONTRAST VOLUME PHASE CHROMA POWER VIDEO RGB/ EXT Y/C B COMPO(SDI) SYNC A ON OFF ENTER INPUT SELECT 3 r t y o [ BM-H1310SU ] 2 4 56p 78 9qwe u i COLOR BLUE MEMORY UNDER PULSE OFF CHECK MODE MENU DEGAUSS SCAN CROSS VOLUME PHASE CHROMA BRIGHT CONTRAST POWER VIDEO RGB/ EXT Y/C A B COMPO(SDI) SYNC ON ENTER OFF INPUT SELECT 3 r t y o 11111 Tally
ページ5に含まれる内容の要旨
TERMINALS AND FEATURES (REAR) (Rear) 23 89 w AUDIO IN OUT IN OUT IN OUT VIDEO A Y / C OPEN 75 ¶ OPEN 75 ¶ VIDEO B RGB/COMPO(SDI) G / Y 4 OPEN 75 ¶ OPEN 75 ¶ e 5 SYNC B / B-Y OPEN 75 ¶ OPEN 75 ¶ r TALLY/ R / R-Y REMOTE 7 FOCUS OPEN 75 ¶ 1 6 p q t y 11111 Power socket qqqqq RGB/COMPO(SDI) termination switch Connect to an AC outlet (120 V AC, 50 Hz / 60 Hz) using Functions as for 33333. the provided power cord. wwwww AUDIO A terminals 22222 VIDEO A terminals Audio signal input terminal and bridge
ページ6に含まれる内容の要旨
CONNECTION EXAMPLE l Be sure to turn off each component’s power before connection. NOTE l The connection shown below is only an example. Terminals and their functions differ in accordance with a component to be connected. Also read and follow the instructions for the component. For audio signal input from the Component that outputs a Component that outputs a Component that outputs Y/C signals composite video signal composite video signal component connected to VIDEO A IN 33333 11111 22222 44444
ページ7に含まれる内容の要旨
BASIC OPERATION 1. To turn the power on: VIDEO A + Input mode Push the POWER switch. NTSC + Color system The POWER indicator glows green. The mode and color system of an input signal are automatically discerned and displayed on screen for about 3 seconds. To turn off power, push the POWER switch again, and the POWER indicator goes off. 2. To select the input: Push an INPUT SELECT switch. Push VIDEO A, VIDEO B, RGB/COMPO(SDI) or Y/C. The mode and color system of a selected input signal are auto
ページ8に含まれる内容の要旨
PICTURE ADJUSTMENTS Turn a separate front panel control to adjust picture contrast, picture brightness, picture color density, and picture hue respectively: CONTRAST (picture contrast) CONTRAST Softer Clearer BRIGHT (picture brightness) BRIGHT NOTE Darker Brighter l To adjust the CHROMA and PHASE controls more precisely, input the color bar signal and operate the BLUE CHECK function as follows: CHROMA (picture color density) After inputting the color bar signal, CHROMA pus
ページ9に含まれる内容の要旨
VIDEO SIGNAL CONTROLS Push each switch to ON or OFF for video signal control. UNDER SCAN Push the UNDER SCAN switch to reduce the dimensions of display area so the whole picture is displayed on screen. Use to check the picture frame. PULSE CROSS Push the PULSE CROSS switch to simultaneously display two blank areas crossed horizontally and vertically on screen (“Pulse Cross” display) by delaying the phase of the input signal. Use to check the vertical retrace line period, equalizing pulse period,
ページ10に含まれる内容の要旨
ON-SCREEN MENU CONTROLS By calling up the menu display on screen, various functions can be selected and set as needed. NOTE Calling up the menu display, selecting an item 11 l When the menu display 111 (shown at left below) is on screen, press the 1. Press the MENU button to call up the menu display on screen (see 11111 ENTER button. The display changes below). (Press again to make the display disappear.) 22 to 222 (shown below center). In this 2. Press the s or t button to select an item to be
ページ11に含まれる内容の要旨
ON-SCREEN MENU CONTROLS (continued) PEAKING FREQ./PEAKING LEVEL (picture quality improvement) NOTE Corrects the luminance signal to improve picture quality by changing l When analog RGB signals are input peak frequency and/or peak level depending on the video signal input to to the monitor, the indications do not the monitor. Use PEAKING FREQ. to set correction frequency. Use appear and the functions cannot be PEAKING LEVEL to set correction level. operated. Setting (ferquency)
ページ12に含まれる内容の要旨
MEMORY MODE A set of picture settings can be programmed in memory for quick recall when necessary. Recall/release of memory mode NOTE Press the MEMORY MODE switch to recall a set of picture settings l If you attempt to operate a locked programmed in memory. function, “MEMORY MODE ON!!” Pressing the switch locks the functions of the front-panel PHASE, appears on screen for approx. 2 CHROMA, BRIGHT, CONTRAST controls, and remote-control picture seconds to indicate the function adjustments not to b
ページ13に含まれる内容の要旨
MEMORY MODE (continued) 3. Press the s or t button to select a function to be revised. qMEMORY MODE REV I SE CONTRAST :0 BR I GHT :0 Press the ENTER button after selecting PICTURE ADJUSTMENT to call up CHROMA :0 PHASE :0 display 22222. ENTER : After making all settings on screen, press the MENU button to make display 111 appear. 11 4. Press the or button to change the set level. 22 222 Adjustable CONTRAST, BRIGHT, CHROMA or PHASE range depends on each set level previously s
ページ14に含まれる内容の要旨
SET-UP FOR MONITOR INSTALLATION When installing the monitor, make set-up adjustments required for the picture set- tings to match conditions where the monitor is to be used. To call up SET-UP MENU and select a function: qSET-UP MENU r SI ZE /CENTERING 1. To make 1 1 1 1 1 (SET-UP MENU) appear, with the ENTER button pressed, WHI TE BALANCE ADJUST REMOTE SELECT press the MENU button. STATUS D I SPLAY : ON 2. Press the s or t button to select an adjustment item. CONTROL LOCK : O
ページ15に含まれる内容の要旨
SET-UP FOR MONITOR INSTALLATION (continued) WHITE BALANCE ADJUST (white balance adjustments) NOTE Before making these adjustments, select the color l By making white balance temperature 9300K or 6500K on MENU. adjustments on SET-UP MENU, [ appears to the right of the COLOR Adjustment (level) Function TEMP. setting on MENU RED DRIVE (-10,-9…0…+9, +10) Adjusts the drive level of a red signal component. (see page 11). GREEN
ページ16に含まれる内容の要旨
SET-UP FOR MONITOR INSTALLATION (continued) STATUS DISPLAY (setting the status display to on/off) When the power is turned on or the input mode is switched, the status display (color system and input mode) appears on screen. The display can be set to on or off. Setting Function ON Status display appears. OFF Status display does not appear. CONTROL LOCK (deactivation of front-control functions) NOTE Set CONTROL LOCK to ON on screen to deact
ページ17に含まれる内容の要旨
PICTURE SETTING INITIALIZATION The MENU and/or SET-UP MENU settings, including changes added later by the user, can be reset (initialized) to their initial (default) settings. To initialize MENU settings only NOTE MENU settings (except MEMORY MODE and RGB/COMPO(SDI)) can l For initial (default) MENU settings, be exclusively reset: see page 21. 1. With the t button pressed, press the MENU button to display 11111 on screen. qMENU rRESET 2. l Press the ENTER button to reset. Are you
ページ18に含まれる内容の要旨
REMOTE CONTROLS The optional wireless remote control unit (RM-C550W) operates the following: l On-screen menu functions (MENU, SET-UP MENU, etc.) l Picture adjustments (CONTRAST, BRIGHT, CHROMA, PHASE) l Sound adjustments (VOLUME, MUTE) On-screen menu remote operation Remote keys and front controls with the same designation share the common functions. For detailed operation, see instructions about each menu function in this manual. NOTE l When monitoring the picture of analog RGB signals, compon
ページ19に含まれる内容の要旨
EACH REMOTE CONTROL OF PLURAL MONITORS To operate or adjust plural units of monitors, by programming and assigning an ID number (00 to 99) for each monitor, a specified monitor can be remote-controlled. To program an ID number (use front controls): q IN I T IALIZE MENU r ID NUMBER SET 1. Press the POWER switch to turn the power off. qSET - UP MENU rRESET ENTER 2. With the t and MENU buttons pressed, press the POWER switch to turn the power on. Keep pressing the t and MENU buttons until 1
ページ20に含まれる内容の要旨
BEFORE CALLING FOR SERVICE Before concluding a problem has occurred, check the following points. If the problem persists after carrying out the checks, disconnect the power cord from the AC outlet and consult the dealer from whom you purchased the monitor. Problems Points to be checked Measures Inoperable adjustment controls Is MEMORY MODE switched on? Switch off. or buttons. Is CONTROL LOCK activated? Deactivate it. Abnormal picture adjustments Are PICTURE ADJUST menu Reset to standard settings
