ページ1に含まれる内容の要旨
49-1000
Plug ‘n Power
Wireless Security System
AC adapter
security console
motion detector keychain remote
door/window sensor
and magnet
Thank you for purchasing your Wireless Security System from
RadioShack.
what’s included
security console
keychain remote (1)
mounting hardware
AC adapter
magnets (2)
motion detector (1)
door/window sensors (2)
Please read this user’s guide before installing,
setting up and using your new product
www.radioshack.com
49-1000 UG.indd 1 7/27
ページ2に含まれる内容の要旨
The Basics contents Introduction 3 Installing Your Security System 4 Locating Security System Components 4 Attaching Your Cords 4 Installing the Backup Batteries 5 Locating Your Security Console 5 A Look at Your Security Console 5 Setting Up Your Security System 6 Reviewing Your Menu Options 6 Initializing/Registering Your Keychain Remote 8 Initializing Your Door/Window Sensors 8 Registerin
ページ3に含まれる内容の要旨
ページ4に含まれる内容の要旨
The Basics Installing Your Security System locating your system components Choose a central location for your Security Console that is near a modular telephone jack and an AC outlet. You can place it on a shelf or table, or mount it on a wall. Plan the location of the Door/Window Sensors and Motion Detectors so the RF path, which runs in a straight line from the sensor to your Security Console, is not obstructed by large metal objects, such as a refrigerator or freezer. Be sure it passes th
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
Beyond the Basics Setting Up Your Security System reviewing your menu options After you’ve connected power to your Security Console, the display shows the time of day on the bottom left line, and “HOME CONTROL” in the top line. All features (except Home Control) require access to the Menu mode. To do this, press either of the Menu / buttons. The display then shows “ENTER PIN” (Personal Identification Number) in the top line. Enter the default PIN (0000). This clears the top line and show
ページ7に含まれる内容の要旨
Beyond the Basics a look at your sub-menus After pressing ok at the first menu level, you can select the sub-menus under that menu item. Or, you can go directly to the sub-menu item by pressing the corresponding number button. Phone Numbers Sub-menu You can enter up to six phone numbers (up to 16 digits), which your system will dial in the event your system cannot reach anyone on a specific phone number. Select PHONE 1 - PHONE 6 to enter a phone number. off/pm enters a pause if you need to
ページ8に含まれる内容の要旨
Beyond the Basics initializing your keychain remote Arm Press and hold the arm button on your Keychain Remote for three to four seconds, and then release it. This initializes the remote and picks a random code that is used when it is registered with your Security Console. registering your keychain remote with your Security Console Press either of the Menu / buttons. The display shows “ENTER PIN” in the top line. When you enter your PIN, * displays for each number entered. Press ok
ページ9に含まれる内容の要旨
Beyond the Basics registering your Door/Window Sensors with the console Press either of the Menu / buttons. The display shows “ENTER PIN” in the top line. When you enter your PIN, * displays for each number entered. Press ok when you see “INSTALL” on the display. Move the magnet away from your Door/Window Sensor. Your Security Console acknowledges that it has been registered with a chime and displays “ZONE 1 SET.” Repeat this for other Door/Window Sensors you want to register.
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
Beyond the Basics initializing your Motion Detector Remove the cover on the front of the Motion Detector and install two AA alkaline batteries in the compartment, matching the polarity (+ and -) marked inside. Replace the cover. Press and hold the TEST button on the back of TEST your Motion Detector for three to four seconds, and then release it. This initializes your Motion Detector and picks a random code that is used when it is registered with your Security Console. Place the unit fa
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
Beyond the Basics changing your Personal Identification Number (PIN) Press Menu / and enter your old PIN. When you see “INSTALL” on your Security Console, press Menu / until you reach the “NEW PIN” menu. Press ok. You also can press 5 to go directly to the “NEW PIN” menu. Enter your new PIN and press ok. Note: Choose a PIN you are not likely to forget. If you forget your PIN, you will not be able use the system. Contact your local RadioShack store to find out how to reset your s
ページ16に含まれる内容の要旨
Beyond the Basics Use Menu / to choose from the following sub-menu items: CHIME 1. CHIME ON 2. CHIME OFF (No chimes when doors/windows are opened) SIREN 1. SIREN ON 2. SIREN OFF (Silent Alarm) HOUSECODE Press the Menu / buttons to change. LIGHTCODE Press the Menu / buttons to change. setting delays Press Menu / and enter your PIN. When you see “INSTALL” on your Security Console, press Menu / until you reach the “DELAYS” menu. Press ok. You also can press 8 to
ページ17に含まれる内容の要旨
ページ18に含まれる内容の要旨
Beyond the Basics Using Your Security System arming your system arm home/away Press arm home on your Security Console to arm all Door/Window Sensors instantly. Motion Detectors will not trip the system when it is armed in the “ARM HOME” mode. Press arm away to arm all Door/ Window Sensors and Motion Detectors. This arms the system after a set delay. If you arm the system in the “AWAY” mode, you also will have an entry delay when you enter your home before the alarm trips, to give you t
ページ19に含まれる内容の要旨
Beyond the Basics You can’t arm the system until you fix the problem zone, or bypass the zone. If you try to arm the system before resolving the problem zone(s), a repetitive “trouble alarm” sounds to alert you to respond. If your Security Console has been tampered with, i.e. the door to the upper right of the display is open, the problem must be fixed (close the door) before you can arm the system. Note: If the system is armed and this door is tampered with, the alarm trips. If you bypass a
ページ20に含まれる内容の要旨
Beyond the Basics if your security console is tampered with If your system is armed and someone tampers with (opens the cover on a Door/Window Sensor, the Motion Detector or the Security Console), the alarm is tripped and a loud siren sounds. If the system is not armed and someone tampers with a Sensor or the Security Console, the word “TAMPER” appears in the display, but the system does not trip. You must correct this by pressing arm and then disarm before you can arm the system. control
