ページ1に含まれる内容の要旨
INSTALLATION/OPERATION
CST150/CST100
Camera Setup Tool
®
C2912M-A (2/05)
ページ2に含まれる内容の要旨
Regulatory Notices The CST150 and CST100 compact field service tools enhance the ease of install of our new Pelco cameras. Both tools incorporate three menu buttons for accessing the setup menus on 5100 Series cameras. Both tools also access video through a 2.5 mm service connector on Pelco’s 5100, 3610, ® 3710, and 3770 Series cameras and the ICS090 Series Camclosure integrated camera system. Radio and Television Interference This equipment has been tested and found to comply with the
ページ3に含まれる内容の要旨
Description The CST150 and CST100 compact field service tools enhance the ease of installing our new Pelco cameras. Both tools incorporate three menu buttons for accessing the setup menus on 5100 Series cameras. Both tools also access video through a 2.5 mm service connector on Pelco’s 5100, 3610, ® 3710, and 3770 Series cameras and the ICS090 Series Camclosure integrated camera system. CST100 BUTTONS CST150 SERVICE PLUG BUTTONS BATTERY BNC COMPARTMENT SERVICE ADJUSTER PLUG LANYAR
ページ4に含まれる内容の要旨
Setup SELECTING VIDEO FORMAT (CST150) A switch for selecting the video format for the microdisplay on the CST150 is located in the battery compartment. To select the video format: 1. Remove the battery compartment cover. You may have to use a small screwdriver. 2. Remove the batteries. 3. Use a pen or small screwdriver to move the switch to either NTSC or PAL. 4. Reinstall the batteries. Make sure you orient the batteries according to the + and – symbols in the compartment for each batt
ページ5に含まれる内容の要旨
INSTALLING/REPLACING BATTERIES (CST150) The CST150 requires three standard AA batteries to power the microdisplay. These batteries provide up to eight hours continuous operation. To install new batteries: 1. Remove the battery compartment cover. You may have to use a small screwdriver. 2. Remove the old batteries. 3. Install the new batteries. Make sure you orient the batteries according to the + and – symbols in the compartment for each battery. 4. Reinstall the battery compartment cove
ページ6に含まれる内容の要旨
Operation USING THE LANYARD The lanyard (supplied with the CST150) helps you secure the CST150. When slipped around your wrist or neck, the tool will not fall to the ground if dropped. Figure 4. Using the Lanyard CONNECTING TO A CAMERA USING THE SERVICE PLUG The service plug lets you easily access video from any camera with a 2.5 mm service connector, ® including the ICS090 Series Camclosure integrated camera system and Pelco’s 5100, 3610, 3710, and 3770 Series cameras. To conn
ページ7に含まれる内容の要旨
USING THE ADAPTER CABLE (CST150) The adapter cable lets you easily access video from the composite video output (BNC) on any camera and display it on the microdisplay. To view camera video: 1. Connect the adapter cable to the service plug. 2. Connect the adapter cable to the BNC connector on the camera. Camera video appears on the microdisplay. ADAPTER CABLE BNC SERVICE PLUG Figure 6. Connecting to the BNC Connector C2912M-A (2/05) 7
ページ8に含まれる内容の要旨
FOCUSING THE VIEWFINDER (CST150) The CST150 offers an 800 x 225 pixel TFT microdisplay. Use it to view video from the camera. As soon as you connect the service plug or the adapter cable to a camera, video appears on the microdisplay. To focus the viewfinder, move the adjuster either left or right (refer to Figure 7). Figure 7. Focusing Viewfinder NOTE: If you cannot focus the viewfinder, check the camera focus. 8 C2912M-A (2/05)
ページ9に含まれる内容の要旨
ACCESSING SETUP MENUS (5100 SERIES CAMERAS) The CST150 and CST100 tools let you configure a 5100 Series camera from the setup menus. Figure 8 indicates the relationship between the menu buttons on the camera and the buttons on the CST150/ CST100. TOP CENTER BOTTOM Figure 8. Accessing Setup Menus (5100 Series Camera) To access the setup menus on the 5100 Series camera, press the center button. The setup menus should appear on the microdisplay or analog monitor. Refer to the CCC5100H Seri
ページ10に含まれる内容の要旨
Specifications MODELS CST150 Camera setup tool with 800 x 225 pixel TFT microdisplay CST100 Camera setup tool with composite video output SUPPLIED ACCESSORIES (CST150 only) Lanyard (attached) One Adapter cable One AA batteries Four (one spare) GENERAL Service Plug 2.5 mm, three-conductor plug with 36-inch (91.4 cm) cable Viewable Area (CST150 only) 800 x 225 pixels Video Output (CST100 only) BNC, for video output to analog monitor POWER CST150 Power Consumption 650 mW Power Sour
ページ11に含まれる内容の要旨
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products and the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X. ® ® • Three years on all other fixed camera models
ページ12に含まれる内容の要旨
® Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East | | | | | | | |
