ページ1に含まれる内容の要旨
0
CAM CLEAR
7 8 9
KBD300
MADE IN USA.
1 23
4 5 6
MON ACK PREV NEXT HOLD PATTERN PRESET MACRO PGM
F1 F2 F3 F4 F5
SEQUENCE
SHIFT
®
KBD300
Universal
Keyboard
Installation/
Operation Manual
C527M (11/97)
Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel (1-209) 292-1981 or FAX (1-209) 348-1120 • DataFAX (1-209) 292-0435
ページ2に含まれる内容の要旨
CONTENTS Section Page 1.0 GENERAL ..................................................................................................1 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 1 2.0 DESCRIPTION .......................................................................................... 2 3.0 INSTALLATION .......................................................................................... 4 3.1 WALL JACK WIRING ......................................................
ページ3に含まれる内容の要旨
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclosure, it is designed for Indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco.
ページ4に含まれる内容の要旨
2.0 DESCRIPTION The KBD300 keyboard provides complete programming and operational control of the CM6700 Matrix Switcher. This keyboard features a three axis joystick that in- cludes a twisting, return-to-center head for full control of variable speed pan, tilt and zoom fuctions. Included in this package: Qty Description Pelco Part Number 1 KBD300 Keyboard, 120 VAC, or KBD300 KBD300 Keyboard, 230 VAC KBD300-X 1 12 VAC wall mount transformer, 120 VAC, or TRF112.0S.20 12 VAC wall mount transformer
ページ5に含まれる内容の要旨
2 3 4 5 6 * The turbo pan 1 7 feature may be SHIFT disabled. Place switch 4 on the F1 F2 F3 F4 F5 SEQUENCE 17 rear panel DIP switch block in MON ACK PREV NEXT HOLD PATTERN PRESET MACRO PGM the off position. 1 23 NEAR FAR See Figure 4. 4 5 6 OPEN CLOSE 8 16 7 8 9 9 0 CLEAR CAM 15 10 KBD300 MADE IN USA. 12 * 14 13 11 1. DIGIT DISPLAY LED Displays monitor number in Run 6. FUNCTION KEYS, Multiplexer Mode (Shift Key LED mode and P in program mode. Illuminated) F1 Press to activate digital zoom. 2. SH
ページ6に含まれる内容の要旨
3.0 INSTALLATION NOTE: Refer to the CM6700 Communication to the CM6700 keyboards is RS-485. Wall jack, modular data cable, and 12 VAC transformer (all supplied) combine to provide a local, single cable plug- Installation/Operation Manual in connection to the keyboard. A double-sided sticky pad, to secure the wall jack to (C523M-A) for detailed operating a suitable surface, is also supplied. instructions. All cabling between wall jacks is user supplied. Maximum cable distance for RS-485 communi
ページ7に含まれる内容の要旨
3.1 WALL JACK WIRING IMPORTANT: Wall jacks must be 1. Determine the location of all keyboards. wired in a daisy-chain configura- 2. Run wall jack interconnect cable (user supplied) from the SCU to the closest tion. keyboard location. Then to the next nearest location, and the next, etc. Wall jacks must be within 6 feet (1.8 m) of the nearest suitable electrical outlet. Do not mount the wall jack at this time. 3. Make cable connections between wall jacks according to Figure 2. All connec- tions
ページ8に含まれる内容の要旨
USER SUPPLIED SCU CABLE (SEE FIGURE 2) WALL JACK ADDITIONAL CM6700 SCU KEYBOARDS VIDEO INPUTS AS NEEDED VIDEO OUTPUTS 1 1 3 5 7 9 11 13 15 2 3 2 4 6 8 10 12 14 16 4 KBD KBD 6' CABLE WALL TRANSFORMER SWITCHER/CONTROLLER DATA CABLE 10' CABLE KEYBOARD DATA CABLE Figure 3. Keyboard Cabling Diagram KEYBOARD KBD300 RJ-45 D ATA CONNECTOR PIN 1 DIP SWITCH COVER PLATE PIN FUNCTION 1 TxD+ 2 TxD- 3 12 VAC/DC } 4 NON POLAR 5 GND 6 7 RxD- 8 RxD+ 1234 KEYBOARD DIP SWITCH Figure 4. Keyboard Rear Panel 6 Pe
ページ9に含まれる内容の要旨
3.2 KEYBOARD ADDRESSING NOTE: Assign keyboard addresses Each keyboard in the system must have a different address. To make program- logically, in ascending order, to avoid ming easier, address keyboards in ascending order. confusion when keyboard access to Set the keyboard DIP switch address, refer to Figure 4. monitors is programmed. The ad- dress assigned determines the key- 1. Remove the two screws and the DIP switch cover plate from the rear of the board number in the access menu. keyboard.
ページ10に含まれる内容の要旨
4.0 SPECIFICATIONS Keyboard Keypad: Mechanical Joystick: 3 axis, vector solving, with twisting return-to-center head 7-Segment Digital Display: Red LED, 2 cells Shift Mode Indicator: Green LED Electrical Input voltage: 12 VAC or ±12 VDC Power Consumption: 1 watt Ambient Operating Temperature: 20° to 120° F (-7° to 49° C) Humidity: 10% - 90% non-condensing Connector Type: RJ-45 8-pin modular (female) Keyboard Communication Protocol: RS-485 Baud Rate: 9600 General Dimensions: 9.50" x 7.125" x 2.2
ページ11に含まれる内容の要旨
NOTES Pelco Manual C527M (11/97) 9
ページ12に含まれる内容の要旨
5.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one (1) year after the date of shipment. Exceptions to this warranty are as noted below: • Two (2) years on all standard motorized and fixed focal length lenses. ® ® • Two (2) years on Legacy , Intercept , CM6700/CM8500/CM9500/CM9750/ CM9760 Matrix, Spectra™, DF5 Series and DF8 Fixed Dome products. • Two (2) years on WW5700 series
