ページ1に含まれる内容の要旨
Galaxy
16 and 16 plus
User Guide
Honeywell Security
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Table of Contents Introduction ........................................................................................ v QUICK OPERATION GUIDE ............................................................. vii GLOSSARY OF TERMS ..................................................................... ix KEYPAD INFORMATION ..................................................................... 1 Star ( ) Key Features ..................................................................................
ページ4に含まれる内容の要旨
Operation of the Test Option ...................................................................................... 11 Option 9 – Log ............................................................................................. 11 Selecting the Log Option ........................................................................................... 11 The Event Log ........................................................................................................... 11 Option 10 – Time .......
ページ5に含まれる内容の要旨
INTRODUCTION The Galaxy 16 and 16 plus control panels are designed to the highest specifications and requirements using the most advanced software and hardware technology. The Galaxy 16 and 16 plus are designed to satisfy the requirements of domestic and smaller commercial installations, yet are flexible enough to provide ease of use and operational versa- tility. This User’s Guide contains the information required to operate the system. The installation engineer will program and commission the
ページ6に含まれる内容の要旨
vi
ページ7に含まれる内容の要旨
QUICK OPERATION GUIDE A SET (an Unset system) B PART SET (Defaults to Parts 1 and 2) 1 key • toggles the Set (ON)/Unset (OFF) status of Part 1 2 key • toggles the Set (ON)/Unset (OFF) status of Part 2 3 key • toggles the Set (ON)/Unset (OFF) status of Part 3 e n t UNSET (a Set system) 1 OMIT ZONES A or B key to view zones # to change omit status of zone (must be an omittable zone) ent key to accept programming and start setting esc key to accept programming without setting 2 CHIME ZONES A or B
ページ8に含まれる内容の要旨
viii
ページ9に含まれる内容の要旨
GLOSSARY OF TERMS Chime: Zone attribute which gives an audible indication of the activation of a detector or contact. Duress: Applicable when a remote signalling device is fitted. A Duress code entered at the keypad will unset the system but transmit a Duress code to the Alarm Receiving Centre. Entry Time: The preset time allowed for users to reach the keypad and unset the system. Exit Time: The preset time allowed for users to leave the building after the setting routine has been initiated. Exi
ページ10に含まれる内容の要旨
x
ページ11に含まれる内容の要旨
KEYPAD INFORMATION The Galaxy system is programmed and operated from the LCD keypads. 2 x 16 CHARACTER LCD DISPLAY GALAXY 16+ V2.7 08:58 TUE 22 NOV A 1 2 3 B 4 5 6 ent 9 7 8 esc 0 # * POWER LED Figure 1: Galaxy Mk 7 LCD Keypad. Number Keys (0–9): are used to enter your User Code and to select and modify options. View (A and B) Keys: are used to set the system and to step through the menu options during programming. Enter (ent) Key: The ent key allows you to unset the system, to access the m
ページ12に含まれる内容の要旨
Power LED: The green power LED remains lit whenever the system is connected to the a.c. mains power supply and a charged stand-by battery. A mains power failure is indicated by the LED flashing slowly. A fuse or battery failure is indicated by the LED flashing quickly. Your User Code: is a four digit personal identification number which identifies you to, and allows you to operate, the system. Note: Entry of an invalid code will cause the keypad to display the message INVALID CODE. Entry of six
ページ13に含まれる内容の要旨
SETTING AND UNSETTING THE SYSTEM Setting the System Before Setting the System Before the system is Set ensure that: • All doors and windows are secured. • All areas protected by movement detectors are free from obstructions and any animals are excluded from the areas to be protected. Full Setting the System Enter your User Code and press the A key: • If all the system zones are closed when the setting routine is initiated the keypad sounders will emit a continuous tone and the keypad displays th
ページ14に含まれる内容の要旨
The Parts marked ‘ON’ are Set, those marked ‘OFF’ are Unset. To alter the set/unset status of a Part press the number corresponding to that part, that is, pressing the 1 key toggles the set status of Part 1 between set/unset. The equals sign denotes that what is displayed beside the Part number is the current status of the Part, that is, P1=ON denotes that Part 1 is currently set. Pressing the 1 key will cause the display to read P1✴ OFF, this means that Part 1 is now provisionally programmed as
ページ15に含まれる内容の要旨
Alarm Abort Note: If the system is programmed for Alarm Abort a period of 90 seconds after expiry of the Entry Time is provided to enable the user to cancel an alarm caused by exceeding the Entry Time or deviating from the entry route. If the 90 second Alarm Abort time is exceeded then a full alarm may result in the Police being called to the premises and the system requiring an Engineer Reset. The installation engineer will explain the operation of the Alarm Abort function where necessary. Canc
ページ16に含まれる内容の要旨
6
ページ17に含まれる内容の要旨
USER MENU For access to the menu options enter your user code then press the ent key. The keypad then displays the menu options available to the user. Menu Option Nn o Optio 0t 1 Omi 0e 2 Chim 0k 3 Wal 0s 4 Code 0t 5 Tes 0g 9 Lo 1e 0 Tim Table 2: Menu Options. The user menu offers a selection of up to seven options. All users have access to the Chime and Walk options. The Omit and Codes options are assigned to users, (if required) by the installer. The system manager (User 14) can also: • test o
ページ18に含まれる内容の要旨
Omitting Zones When the Omit option is selected, zone 01 is displayed, along with it’s omit eligibility and status (NON OMITTABLE – the zone cannot be omitted; #,xx OMIT – the zone is omittable (where xx is the zone number); OMIT – the zone is currently omitted). If the zone is currently omitted then the box on the top line of the display is filled; if zone is not currently omitted then the box is empty. If the zone can be omitted and the omit status is to be changed, press the # key. The dis
ページ19に含まれる内容の要旨
On selecting the Walk option zone 01 is displayed. If the zone is to be tested press the # key. Use the A or B keys to scroll through the zones on the system, each one may be selected for inclusion in the test. When all the required zones have been selected press the ent key to start the Walk Test. The keypad displays the number of Walk Test zones currently open on the system. Pressing the A or B keys allows the currently open zones to be viewed. Walk test the selected zones by activating the ap
ページ20に含まれる内容の要旨
Note: User Code 13 may be assigned as a Duress Code. Entry of this code causes a Duress alarm which will activate the PA outputs and trigger the Remote signalling Device (if fitted); the Horn, Bells and Strobe outputs do not activate. The installation engineer will advise you on the operation of this function where applicable. Assigning User Attributes Ne oAn ttribut Descriptio 0s 1 Set Acces Enables the user to Set the system using the A key. 0s 2 Unset Acces Enables the user to Unset the syste