ページ1に含まれる内容の要旨
Model AM5
Owner’s Guide
ページ2に含まれる内容の要旨
Limited lifetime consumer warranty Directed Electronics (“Directed”) promises to the original purchaser to repair or replace (at Directed’s election) with a comparable reconditioned model any Directed unit (hereafter the “unit”), excluding without limitation the siren, the remote trans- mitters, the associated sensors and accessories, which proves to be defective in work- manship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the un
ページ3に含まれる内容の要旨
DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECT- ED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEA
ページ4に含まれる内容の要旨
contents Limited lifetime consumer . . . . . Disarming without a . . . . . . . . transmitter . . . . . . . . . . . . . . . .7 warranty . . . . . . . . . . . . . . . . . . . .i Valet mode . . . . . . . . . . . . . . .9 Trademarks and copyrights . . . . .1 Remote valet . . . . . . . . . . . . . .9 What is included . . . . . . . . . . . . . .2 Panic mode . . . . . . . . . . . . . .10 Important information . . . . . . . . .2 Auxiliary mode . . . . . . . . . . .10 System maintenance . . . . . . . .
ページ5に含まれる内容の要旨
What is included Control module and harnesses ® A Stinger dual stage shock sensor (on-board the control module) Two 4-button transmitters Pre-wired Valet button with integrated status LED XR Plus receiver ® Failsafe Starter Kill relay (if equipped) Important information Congratulations on the purchase of your security system. Due to the complexity of this system, it must be installed by an authorized dealer only. Installation of this product by anyone other than an authorized dealer voids
ページ6に含まれる内容の要旨
Your warranty Your warranty registration must be returned and the bar code serial number must not be removed. If the warranty registration is not returned, you do not have a warranty. It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer. Make sure that you receive the warranty registration from your dealer. Fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) T
ページ7に含まれる内容の要旨
Standard transmitter configuration controls the Arm and Multi-level arming function. controls the Disarm. controls Auxiliary channel 2 output and Silent Mode controls Panic mode. and pressed together controls channel 3 output. © 2008 Directed Electronics All rights reserved 4
ページ8に含まれる内容の要旨
Using your system manual (active) arming The factory default is active arming. In this mode you can activate, or arm, the system by pressing the button on your transmitter. When the system arms, you will hear a short horn honk and see the parking lights flash once. While the system is armed, the status LED will flash about once per second, showing that the system is actively protecting your vehicle. If you hear a second short horn honk after arming, and see the status LED flashing in groups, see
ページ9に含まれる内容の要旨
n no otte e:: If any protected entry point (such as a door or a switch- protected trunk or hood) is open, the system will not passively arm. Additionally, each time a sensor is triggered during the arming countdown, the 30-second countdown starts over. Silent mode To temporarily turn off the arm or disarm honkss, use Silent Mode™. Press for less than one second before arming or disarming, and the confirmation honks will be eliminated for that one operation only. If you want the arm/disarm honks
ページ10に含まれる内容の要旨
sive response gives you time to disarm the system with your transmitter if you inadvertently open the door while the sys- tem is armed, while still providing instant response (even if the door is immediately closed). n no otte e:: If programmed for instant trigger, the horn will output full trigger response after the door has been opened (see Programming Options) Turning on the ignition key triggers the same progressive response as opening a door. If equipped, the starter interrupt prevents t
ページ11に含まれる内容の要旨
Integrated LED status indicator ® LED/Valet switch Open the door and the alarm sounds. Turn the ignition to the “run” position. Press and release the integrated LED/Valet button, within 10 seconds. DRW-35 After a few seconds the LED stops flashing, the alarm shuts off, and the vehicle starts. If it does not, you may have waited too long. Turn the ignition off and try again. n no otte e:: The setting for the number of times the integrated LED/Valet switch must be pressed is set in the Program
ページ12に含まれる内容の要旨
Valet mode You can prevent your system from arming, by using Valet Mode. This is very useful when washing the vehicle or having it serviced. In Valet Mode, the system will not arm, even with the transmitter, but all con- venience functions (door locks, trunk release, etc.) will work normally. To enter or exit Valet Mode with the integrated LED/Valet but- ton: Turn ignition to “on” position, then turn to “off” position. Press and release the integrated LED/Valet button within 10 sec- DRW-35 onds
ページ13に含まれる内容の要旨
Panic mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter. Just press for two seconds to enter Panic Mode. In Panic Mode, the horn will honk and the parking lights will flash for 30 seconds. To stop Panic Mode at any time, press on the transmitter again. n no otte e:: In order for Panic Mode to be effective, the vehicle’s horn (or optional siren) as well as the vehicle's parking lights must be connected. Auxiliary mode The
ページ14に含まれる内容の要旨
Lock Button Number of Horn Armed State with pressed honkss Zone(s) Bypassed X times Once 1 honk All zones active 2 honks followed by Twice Zone 2 bypassed long honks 3 honks followed by Three Zone 4 bypassed long honks 4 honks followed by Four Zone 2 & 4 bypassed long honk 5 honks followed byAll zones bypassed, Five long honks except zone 5 (ignition) Long term event history The system stores the last two alarm triggers in memory and can be dis- played by: With the ignition off, press and hold
ページ15に含まれる内容の要旨
The LED will flash in two groupings representing the last 2 zones trig- gered. For example, if zone 2 and 3 were the last two triggered, the LED would flash two times followed by a pause then it would flash three times followed by a pause. Turn off the ignition switch or wait one minute to exit the history display. See Table of Zones on p. 14 for zone information. ® Nuisance prevention circuitry ® Your system has Nuisance Prevention Circuitry (NPC). This circuitry pre- vents annoying repetitive
ページ16に含まれる内容の要旨
bypassed until the trigger ceases. n no otte e:: Arming and disarming the system does not reset this function! The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the ignition. If test- ing your system, it is important to remember that this circuitry can cause zones to be bypassed and appear to stop work- ing. If five honkss are heard when disarming, false alarm protection has engaged. If you wish to clear the memory, turn the ignition key on. Diagnosti
ページ17に含まれる内容の要旨
the light goes out, however, the doors are monitored normally 3-sec- onds later. Disarming diagnostics Extra disarm horn honks are the tamper alert. If four short horn honks are heard when disarming, the system was triggered in your absence. If five short horn honks are heard, a zone was triggered so many times that false alarm prevention circuitry has bypassed that zone. In either case, the status LED will indicate which zone was involved (see Table of Zones below). The system will retain this
ページ18に含まれる内容の要旨
Rapid resume logic This system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet Mode and the battery is dis- connected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode. Programming options Programming options control your syste
ページ19に含まれる内容の要旨
First menu 1. Active or passive arming (automatic arming 30-seconds after closing the last door). Auto re-arm: If the security system is disarmed and a door is not opened (within 30 seconds) the alarm re-arms itself. NOTE: Auto re-arm can relock the doors when the alarm re- arms, if passive locking is programmed on. 2. Arming/disarming confirmation short horn honks on or off. 3. Door Trigger Error Short Horn Honk on or off. 4. Ignition-controlled domelight on or off. 5. Door Trigger delayed or
ページ20に含まれる内容の要旨
Second menu 1. Ignition-controlled door locking on or off. 2. Ignition-controlled door unlocking on or off. 3. Active or passive locking. 4. Door lock pulse duration 0.8-seconds or 3.5-seconds 5. Single or double lock pulse. 6. Single or double unlock pulse. 7. Auxiliary output 2nd unlock. The alarm sends a pulse if the and buttons on the remote are pressed simultane- lously then released. It can also send a signal as long as the transmission from the remote is received. The 2nd unlock output s
