ページ1に含まれる内容の要旨
Installation Instructions
TRACKNET™ TN-4003/4004
ページ2に含まれる内容の要旨
TABLE OF CONTENTS TABLE OF CONTENTS Introduction .................................................................................................................................... 2 Installation Caution and Warnings ............................................................................................... 3 Control Module and Components ............................................................................................. 3-4 Mounting Location………………………………………...............
ページ3に含まれる内容の要旨
INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE COMPUTERS, and BATTERY etc.). WE RECOMMEND the use of a VOLT/OHM METER to test and verify wiring circuits. Test lights or illuminated probes can cause damage to on-board computer or engine management systems. DO NOT exceed maximum output ratings or damage may occur. Electrical current limits for the TrakNet are listed w
ページ4に含まれる内容の要旨
CONTROL MODULE & COMPONENT MOUNTING Main Unit: The TrakNet unit has an internal power management program that monitors the vehicle power at all times. The internal power management program is continuously looking at the condition of the battery in order to detect the state of the vehicle operation. The Traknet unit determines the state of the vehicle power by detecting changes in the battery voltage over time. It is critical that the vehicle power be taken from a source as close to the
ページ5に含まれる内容の要旨
MOUNTING LOCATION Selecting the Antenna Locations The Module requires two antennas elements. One antenna is for receiving GPS signals from The Navistar GPS satellites. The second antenna is a radio transceiver antenna that communicates with the Cellular network. The antenna does not require a ground plane to function properly. There are two antenna cables in addition to the main power harness that must be connected to the TRAKNET, so be sure there is room to access the connectors for i
ページ6に含まれる内容の要旨
INSTALLATION Locating Vehicle Power The TRAKNET has an internal power management program that monitors the vehicle power at all times. The internal power management program is continuously looking at the condition of the vehicle battery in order to detect the state of the vehicle operation. The TRAKNET determines the state of the vehicle power by detecting changes in the battery voltage over time. It is critical in this installation that the vehicle power be taken from a source as clos
ページ7に含まれる内容の要旨
INSTALLATION Within five minutes the flash rate will change to approximately one second on and one second off to indicate that the GPS Receiver has established a location “lock”. Within 1 minute the flash color should be green to indicate good cellular coverage. If you do not get the results above, refer to page 13, Section 13 – Troubleshooting Confirming Proper Operation The Test wire (see wiring diagram) on the TRAKNET is for testing the internal functionality of the hardware. Runni
ページ8に含まれる内容の要旨
LED STATUS INDICATOR LED Status Indicator BI-COLOR ON BOARD LED: This unit has a bi-colored LED on unit. SOLID LED COLOR: Solid Green – Device is in Test Mode: no inputs are currently being triggered. Solid Orange – Device is in Test Mode: At least one input is currently being triggered. Solid Red – Device is in set up mode BLINKING LED COLOR: Blinking Green – Microburst and Cellular Service are available. Blinking Orange – Cellular Service, but not Microburst Service i
ページ9に含まれる内容の要旨
WIRING NOTE: Some Options Need to Be Pre-programmed From Crimestopper prior to installing the unit. Pin 1 Black: Chassis Ground Input THIS WIRE MUST BE CONNECTED TO THE CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt to ensure a good connection. Pin 2 Green: Starter Disable (-) (Output #2) Requires Relay This wire has a negative output to hook up to optional relay. See wiring diagram for connection. Pin 3 Blue: GEO Fence (Optional) (-) Input #2 Connect wire to mo
ページ10に含まれる内容の要旨
WIRING Pin 12 Orange: Alarm Trigger (-) Default* or Door Open/Close Input #1 A. Alarm Trigger*: Triggers alarm input of tracking device if received a negative input for 15 seconds or longer. This is connected to the negative siren output, if alarm has positive siren output use a relay to convert to negative. B. Door Open/Close Input :This unit can be programmed for monitoring of door open and close. This configuration must be program see dealer for programming instructions. Pin
ページ11に含まれる内容の要旨
WIRING DIAGRAM 11
ページ12に含まれる内容の要旨
ACCESS INFORMATION Congratulations, you have just installed the Internet based vehicle telematics system. Now that it’s installed, here’s how to use your system. Step #1 First fill out your TrakNet registration form and fax to 805.581-9500. Then you will receive a call or email with your login and password. Step #2 Turn on your computer and log on to the Internet using your standard Internet browser. . • Go to: www.nationstrack.com . • Enter customer login and password. Then
