ページ1に含まれる内容の要旨
PROSTEEL SAFES
safe
owner’s manual
07-137-BSF_Safe OM.indd 1 7/21/08 11:13:07 AM
ページ2に含まれる内容の要旨
Important Operating Instructions for: Contents Page Thank You for Purchasing a Browning ProSteel Safe ............................2 Browning Prosteel safes Inspecting Your Safe ................................................................................3 If you have any questions about your new safe, this UL Tool Attack Listing .............................................................................3 owner’s manual or other Browning products, contact: Fire Protection Rating ......
ページ3に含まれる内容の要旨
t h a n k y o u f o r P u r C h a s i n g a insPeCting your safe Browning Prosteel safe. Upon receipt of your safe, you should immediately inspect it for any A Browning ProSteel safe is the finest home security safe available. With damage that may have occurred during shipping. If your safe was proper care and installation it will provide you many years of peace of commercially delivered and you detect any damage, call the shipping mind, security and fire protection (fire-resistant models on
ページ4に含まれる内容の要旨
Special fire considerations: Browning ProSteel fire-resistant safes are w ater and fire damage rated to withstand the time and temperature stated on the rating label. Should your safe be exposed to fire or water, the fire-resistant However, when a home burns some portions of that fire may burn at properties of the insulation will be compromised. Do not continue more than 2000° F. Placement of your safe away from potential hot to store valuable items in such a safe. Check with your insuran
ページ5に含まれる内容の要旨
Notice! your browning prosTeel safe is noT designed for which allow the door to open 180° and be removed for easier home installation. The external hinge system in no way compromises security exTerior use. exposing your safe To rain, moisTure or high because there are locking bolts around the perimeter of the door, and humidiTy can cause rusT and damage To The lock and oTher even with the hinges removed the door is secured by the locking bolts. par Ts of The safe. The painTed exTerior finis
ページ6に含まれる内容の要旨
anChoring to a ConCrete floor figure 2 2 Lower the door onto the bottom hinge first, then onto the top pin. Important: Pre-drill the holes 3 When both the top and bottom hinges are aligned lower the door in the safe back and floor prior completely down. to anchoring the safe to the floor 5 4 Close the door and use a /32" Allen wrench to turn the Allen bolt or wall. located in the bottom piece of the bottom hinge four half-turns 1 Remove the safe interior clockwise (looking down at the
ページ7に含まれる内容の要旨
figure 3 IMPORTANT: Pre-drill wall anchor holes in the safe prior to anchoring the safe to the floor or wall. See “Anchoring Your Safe to a Wall” on page 10. 9 Fill the 2" openings in the fire-resistant material with high temperature silicone caulking. The caulking will seal the opening and prevent hot gases from entering the safe during a fire. (Not 2" 2" required on models that are not fire-resistant.) 2" 2" 10 Replace the floor panel, elevation brace and interior shelving. anChoring to
ページ8に含まれる内容の要旨
anChoring to a framed wall 4 Drill down 2" from the top of the safe on each of these stud centers (Figure 4). Mark these spots on the safe’s interior with a IMPORTANT: Pre-drill the holes in the safe back and floor prior to marker. Using a sharp utility knife, cut a 2" x 2" “X” in the carpet anchoring the safe to the floor or wall. on your marks. Anchoring to a framed wall requires the location of your anchor holes 5 Move the safe away from the wall and, using a high-speed bit align with t
ページ9に含まれる内容の要旨
5 Turn your safe handle clockwise to open the safe door. You should immediately change the combination of the electronic lock from the factory default code. The lock instructions outline the IMPORTANT: If you miss any combination number by more than 1 process to program a new electronic lock combination. dial mark your safe will not open. Make sure you are looking straight down at the index marks. Make sure to align the numbers with the IMPORTANT: Record the combination you select, as the
ページ10に含まれる内容の要旨
Gloss Black DAR 9000 Changing the ComBination ® Hunter Green Metallic DAR 4108 Your combination of the S & G Mechanical Lock is pre-set at the Burgundy DAR 74004 factory. Changing the combination will void your lock warranty. If you must change the combination for some reason, contact a Sand Metallic F1929 certified locksmith to do this for you. Black Cherry Sherwin-Williams® 82128 If touch up paint is needed other than that supplied by Browning, you keyloCk can get it at an automo
ページ11に含まれる内容の要旨
figure 5 pliers and lift up. The shelves can be relocated along this track by h i n g e s simply relocating the clips to the desired shelf location. To replace a Your door height is adjusted at the clip, insert the top lip of the clip into the appropriate slot in the track, factory and should not require any squeeze the clip together and insert the bottom lip of the clip into the adjustment when new. However, track. It is important that all clips supporting a particular shelf are hinge
ページ12に含まれる内容の要旨
BulB rePlaCement CarPet 1 Prior to replacing a bulb, turn the light switch off and The key to removing stains from your carpeted interior is to clean unplug the light. Allow the bulb to cool before replacing. them as soon as they occur. Do not soak the carpeting with water to remove stains. Small amounts of water can permanently damage the 2 Twist lens cover counterclockwise. fire-resistant materials within your safe if the water is allowed to soak 3 Use only Type JCDGY8 20 watt 120 volt ha
ページ13に含まれる内容の要旨
Notice! follow only The recommended cleaning procedures and (for destinations in the continental United States). Should any defect be noted, the purchaser agrees to inform ProSteel in writing before use onyl The recommended cleaning ma Terials. f ailure any work is performed. For consumers in Canada, please contact To follow This informa Tion could cause your mirror To Browning Canada. For consumers in Europe or the United Kingdom, become cloudy . please contact Browning International S.A
ページ14に含まれる内容の要旨
Browning.Com Browning us: Morgan, Utah 84050-9326 Browning Canada: Browning Canada Sports Ltd/Lteé, St-Laurent, Quebec H4S 1W6 Browning intl: Parc Industriel des Hauts-Sarts, B-4040 Herstal, Belgium NEU080610/07137 26 07-137-BSF_Safe OM.indd 26 7/21/08 11:13:10 AM
ページ15に含まれる内容の要旨
For customers in Europe or the United Kingdom, please contact: notes Browning International S.A. Parc Industriel des Hauts-Sarts 3eme Avenue #25 4040 Herstal, Belgium 00 32 4 240 52 11 For non-warranty questions, contact Browning at: Browning Consumer Department One Browning Place Morgan, UT 84050 (800) 333-3288 P r o s t e e l f i r e a n d B r e a k - i n limited warranty ProSteel will repair or replace (at ProSteel’s option) free of charge any ProSteel manufactured safe produced aft
